Sanyo LNS W01 Installation Manual
Have a look at the manual Sanyo LNS W01 Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
LCD PROJECTOR LENS REPLACEMENT AND INSTALLATION PROCEDURES English Français Español Deutsch Italiano 1AA6P1P2923-- (MV6A)
- 1 - E LCD PROJECTOR LENS REPLACEMENT AND INSTALLATION PROCEDURES CAUTION When installing or replacing the Projection Lens, refer to this manual. For installation of the lens, use the parts designated in the manual. Do not use the installation manual and Light-Block Sheets in the lens package. Check the following parts supplied to this projector. NOTES ON LENS INSTALLATION ●Lens installation and replacement should be made by the qualified service personnel. ●Be sure to install the lens following this procedure precisely. ●Do not touch or remove any parts except the lens and related parts. It may result in malfunctions, electrical shock, fire hazard or other accidents. ●Before installing or replacing the lens, check the Model No. of the Projection Lens matches to the projector. ●When moving or setting up the projector, be sure to replace the Lens Cover to protect the surface. And be careful not to hold or subject the lens to strong forces. It may damage the lens, cabinet, or mechanical parts. ●For details of the lens and installation, contact the sales dealer where you purchased the projector. ● LIGHT-BLOCK SHEETS 3 pcs. ● LENS MOUNTING ADAPTERS 2 pcs. ● ADAPTER SCREWS 8 pcs. This projector applies the Projection Lenses listed below. Use the suitable lens for where the projector is used. ✳ For installing those lenses, attaching Lens Mounting Adapters or removing Guide Pins is required. Make sure the Model No. of the lens and the installation procedure on next pages and be sure to install the lens precisely. Model NO. LNS-W01✳ LNS-W01Z LNS-T01✳ LNS-T01Z LNS-T02 LNS-W02✳ LNS-W02Z LNS-M01✳ LNS-M01Z LNS-S01✳ LNS-S02✳ LNS-S02Z Type Fixed Short Throw Lens Fixed Long Throw Lens Long Throw Zoom Lens Short Throw Zoom Lens I Semi-Long Throw Zoom Lens Standard Zoom Lens II Standard Zoom Lens I Zoom Motor Driven FixedManual Focus Fixed Motor Driven Motor Driven Motor Driven Motor Driven Manual Motor Driven Motor Driven Motor Driven Motor Driven Motor Driven AVAILABLE LENS LNS-W03 LNS-S03 Short Throw Zoom Lens II Standard Zoom Lens III FixedManual Motor DrivenMotor Driven
UPPER LENS COVER - 2 - E NOTE : The installation procedure and needed parts for lens installtaion depend on the type of the Projection Lens. Check the Model No. of the Projection Lens and be sure to install or replace the lens following procedure below. 1 Remove Lower Lens Cover. Remove 2 Screws A. Push part B and pull Lower Lens Cover down. (See Fig. 1.) 2 Remove 4 Screws C. Pull Upper Lens Cover toward front and remove. (See Fig. 2.) 3 Remove 2 Screws D and Cover Plate on the back of Upper Lens Cover. (See Fig. 3.) LENS REPLACEMENT AND INSTALLTION PROCEDURE A C C B Fig-3 Fig-1 Fig-2 COVER PLATE UPPER LENS COVER LOWER LENS COVER D
- 3 - E 5 Connect Lens Motor Lead to the connector K96T on the circuit board under the lens. (The model with Lens Motor only.) Fix Lens Motor Lead with the wire holder on the circuit board. For installing the lenses listed below, attaching Lens Mounting Adapters is required. Before mounting the lens, attach Lens Mounting Adapters. Refer to LENS MOUNTING ADAPTER INSTALLATION. Model No.: LNS-W02, LNS-S01, LNS-M01 For installing the lenses listed below, removing Guide Pins is required. Before mounting the lens, remove 2 Guide Pins from Lens Mounting Bracket. (See Fig. 4.) Model No.: LNS-W01, LNS-S02, LNS-T01 4 Replace Lens Cap on the rear (mounting side) of Projection Lens and mount the lens on Lens Mouting Bracket with 4 Screws. When installing the model with Lens Motor, be sure to mount the lens with Lens Motor on the right. (See Fig. 4.) GUIDE PINLENS LOCK SCREW Fig-4 DRIVER IN THE LENS LOCATE MOTOR ON RIGHT SIDELENS MOUNTING BLACKET Fig-5 K96T CONNECTOR LENS MOTOR LEAD Part No. (610 275 6029)
- 4 - E 6 This projector has 3 Light-Block Sheets. Use Light-Block Sheet corresponding with lens. (Refer to the list below.) Set Light-Block Sheet through the lens. Make sure the shape of Light-Block Sheets and be sure to set them as shown in the Fig. 6. NOTE: ●Be sure to set each Light-Block Sheets as shown in Fig-6. ● Make sure the mark (TOP and BACK) on Light-Block Sheets and set them properly. Light-Block Sheets For each lens. Lens Model No. LNS-S02, LNS-S02Z, LNS-S03 LNS-M01, LNS-T02, LNS-W02 LNS-M01Z, LNS-W02Z, LNS-S01 LNS-W03 LNS-W01, LNS-T01, LNS-W01Z LNS-T01ZType No. (Part No.) TYPE FD1 (610 290 9258) TYPE FE1 (610 293 8937) TYPE FF1 (610 293 8944) Fig-6 LIGHT BLOCK SHEETS Make sure the sheet figure and put on proper position.
- 5 - E 7 Adjust focus of the Projection Lens. (LNS-W01, LNS-W01Z, LNS-T01, LNS-T01Z and LNS-W03 only.) Set up the projector and project image on the screen. Loosen Focus Lens Lock Screw and rotate Projection Lens to obtain proper focus. After adjusting focus, be sure to lock Projection Lens with Focus Lens Lock Screw securely. (See Fig. 4.) Adjust focus of Projection Lens MODEL LNS- W03, following Focus Adjustment on page 6. 8 Replace Upper Lens Cover. Slide Light-Block Sheets into the guide of Upper Lens Cover and set them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover with 4 Screws C. (See Fig. 2.) 9 Replace Lower Lens Cover. Slide Light-Block Sheets into the guide of Lower Lens Cover and set them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover with 2 Screws A. (See Fig. 1.) 10 Turn the projector on and operate Lens shift, Zoom and Focus fully to check Light-Block Sheets. If Light-Block Sheets interfere with those operations, check Light-Block Sheets are set properly. Fig-7 LOWER LENS COVER LIGHT-BLOCK SHEETS Slide into front of the flap.FLAP Slide upper both side of LIGHT BLOCK Sheets into between and . 21 GUIDE 1 2 UPPER LENS COVER FLAP
- 6 - E Focus Lock Screw Focus Lock Ring ●mark (yellow) FOCUS ADJUSTMENT (For Model LNS-W03) Set up the projector and project image on the screen. 1.Loosen the Focus Lock Screw on the projection lens. 2.Rotate the projection lens to obtain proper focus on center area of the screen. When the distance of the screen and lens is 1 meter, set ●mark (yellow) of the lens on Focus Lock Screw position. 3. Lock the Focus Lock Screw securely. When proper focus is not observed at outer area of the screen, proceed following adjustments. 4.Loosen the Focus Lock Ring on the projection lens. (Turn the Lock Ring to counter-clockwise.) 5.Rotate the lens to obtain proper focus on outer area of the screen. 6. Lock the Focus Lock Ring securely. (Turn the Lock Ring to clockwise.) If proper focus is not observed entire screen, repeat above adjustment 1~ 6.
- 7 - E For installing the lenses listed below, attaching Lens Mounting Adapters is required. Model No.: LNS-W02, LNS-S01, LNS-M01 1 Set Lens Mounting Adapters on the lens with 4 Screws. Use the round head screws. (See Fig. 8.) LENS MOUNTING ADAPTER INSTALLATION Check the following parts supplied with the adapters. ADAPTER SCREWS 8pcs. (4 pcs. for mounting Adapters on the lens and 4 pcs. for mounting Lens on the projector.) NOTE: Do not use the screws in the lens package. 2 Mount Projection Lens on the projector with 4 Screws supplied to the adapters. (See Fig. 9.) BE SURE TO CHECK FOR SAFETY After installing or replacing the lens, be sure to check the following for safety. 1. Check the lens is securely fixed with the screws. 2. Check no wiring is damaged or tangled on the gear of the lens motor or the other mechanical parts. 3. Check no part is missing, or no mounting part is loose. Fig-8 Fig-9DRIVER IN THE LENS C AADAPTER PART NO. 610 289 1676 BSCREW PART NO. 411 001 9303 CSCREW PART NO. 412 062 4009 ✳1 PC NO. ROUND HEAD SCREWS ADAPTER A B For installing the lens, “refer to LENS REPLACEMENT AND INSTALLTION PROCEDURE.” A Some parts are not used for installation or replacement. Keep these parts for later use. NOTE: Figures in this manual may be differ from the actual product.
- 8 - E NOTE: Following tabe shows approximate measurement. Actual measurement depends on lens and projectors.SPECIFICATIONS (Throw distance and screen size, screen of lens shift. ) Model No.LNS-S02 LNS-S02Z Zoom40 6080 100120150 180200 250300 350400500 600 LNS-W02 LNS-W02Z LNS-T02 LNS-M01 LNS-M01Z LNS-S01 LNS-W01 LNS-W01Z LNS-T01 LNS-T01Z MINMAX MINMAXMINMAX MINMAXMINMAXNONENONE1.9 1.5 1.41.15.13.8 3.62.92.31.53.0 2.4 2.11.77.55.5 5.44.33.52.2 4.13.22.92.310.07.37.25.74.62.9 5.24.03.62.912.59.19.07.15.83.7 6.34.9 4.43.414.910.810.88.574.4 7.96.15.54.318.613.513.510.58.85.6 9.67.46.75.222.316.1 16.212.610.66.7 10.78.37.45.824.817.9 18.014.011.87.4 13.410.49.37.231.022.322.517.514.89.3 16.112.511.28.637.126.727.021.017.811.2 18.914.613.110.143.331.131.534.420.813 21.616.715.011.549.535.536.027.923.814.9 27.120.913.714.461.844.345.034.929.718.6 32.525.122.517.374.253.154.041.835.722.4 0.95.6 1.48.4 1.911.2 2.414.02.9 16.8 3.621.04.4 25.34.9 28.1 6.135.17.4 42.18.6 49.2 9.9 56.2 12.3 70.3 14.884.3U/D (MAX) 0 10 18 18 1 8 0 10 18 1 8 SCREEN SIZE (INCH) AND THROW DISTANCE (m) LENS SHIFT/ CENTER RATIO LENS SHIFT (UP/DOWN) H2 H1 H2H1 Upper max Down max 0 10 LNS-W03 NONEMIN ------ ------ ------ 0.6 0.9 1.3 1.6 1.9 2.4 2.9 3.3 4.1 4.9 5.8 6.6 8.3 9.9 NONE MAX ------ ------ ------ 5.27.1 6.38.6 7.910.7 9.512.9 10.614.4 13.318.0 16.021.6 18.725.3 21.428.9 26.836.1 32.243.4 LNS-S03 H1 H2
LNS-S03Lentille IIIde zoom standardMoteur entraîné Moteur entraîné - 1 - F PROJECTEUR A LCD PROCEDURES D’INSTALLATION ET DE REMPLACEMENT DE LA LENTILLE ATTENTION ● FEUILLES DE BLOCAGE LEGER 3 unités ● ADAPTATEURS DE MONTAGE DE LENTILLE 2 unités ● VIS D’ADAPTATEURS 8 unités Ce projecteur accepte les lentilles de projection mentionnées dans la liste ci-dessous. Utilisez la lentille convenant à l’endroit où vous utilisez le projecteur. ✳ Pour installer ces lentilles, il faut fixer les adaptateurs de montage de lentille ou retirer les broches du guide. Vérifiez le n° de modèle de la lentille et la procédure d’installation aux pages suivantes et veillez à installer précisément la lentille. N° de modèle LNS-W01✳ LNS-W01Z LNS-T01✳ LNS-T01Z LNS-T02 LNS-W02✳ LNS-W02Z LNS-M01✳ LNS-M01Z LNS-S01✳ LNS-S02✳ LNS-S02Z Type Lentille pour projection courte fixe Lentille pour projection longue fixe Lentille Ide zoom pour projection courte Lentille de zoom pour projection semi-longue Lentille IIde zoom standard Lentille Ide zoom standard Zoom Moteur entraînéFixe Manuel Mise au point Fixe Moteur entraîné Moteur entraîné Moteur entraîné Moteur entraînéManuel Moteur entraîné Moteur entraîné Moteur entraîné Moteur entraîné Moteur entraîné LNS-W03Lentille IIde zoom pour projection courteFixe Manuel LENTILLE UTILISABLE Lorsque vous installez ou que vous remplacez la lentille de projection, reportez- vous à ce manuel. Pour l’installation de la lentille, utilisez les pièces indiquées dans ce manuel. N’utilisez pas le manuel d’installation et les feuilles de blocage léger contenus dans l’emballage de la lentille. Vérifiez les pièces suivantes fournies avec ce projecteur. Lentille de zoom pour projection longue REMARQUES CONCERNANT L’INSTALLATION DE LA LENTILLE ●L’installation et le remplacement de la lentille doivent être confiés à un technicien d’entretien qualifié. ●Veillez à installer la lentille en suivant rigoureusement la procédure. ●Ne touchez ou ne retirez aucune pièce à l’exception de la lentille et des pièces connexes. Sinon, vous risquerez de produire des anomalies, une électrocution, un incendie ou d’autres accidents. ●Avant d’installer ou de remplacer la lentille, assurez-vous que le n° de modèle de la lentille de projection correspond bien au projecteur. ●Lorsque vous déplacez ou que vous installez le projecteur, veillez à remettre en place le capuchon de lentille pour protéger la surface de la lentille. Veillez aussi à ne pas saisir ou manipuler la lentille avec une force excessive. Sinon, vous pourriez endommager la lentille, le coffret ou les composants mécaniques de l’appareil. ●Pour plus de détails concernant la lentille et son installation, adressez-vous au revendeur chez qui vous avez acheté le projecteur.