Samsung TFT LCD Television T4081F-L User Manual

							
English - 7
Setting Up Anynet+ The following settings help set the Anynet+ functions.
To use the Anynet+ Function, Anynet+ (HDMI-CEC) must be set to On
1.  
Press the Anynet+ button. Press the ▲ or ▼ button to select "Setup", then press the ENTER button.
2.  
Press the ENTER button to select "Anynet+ (HDMI-CEC)", then press the ENTER button.
, Press the ▲ or ▼ button to select "On", then press the ENTER button.
   
The Anynet+ (HDMI-CEC) function is enabled.   
If you select Off, Anynet+ (HDMI-CEC) is disabled.     When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related operations are deactivated.
Setting an Anynet+ Device to turn Off Automatically when the TV is Turned Off
2.  Press the ▲ or ▼ button to select Auto Turn Off, then press the ENTER button.
. Press the ▲ or ▼ button to select "On", then press the ENTER button.
  The "Auto Turn Off" function is enabled.   
If you select "Off", the "Auto Turn Off" function is canceled.
    Press the EXIT button to exit.
    The active source on the TV remote must be set to TV to use the Anynet+ function.    If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned off. If an external device is still recording, it may or may not turn off. 
Scanning and Switching between Anynet+ Devices 1. Press the Anynet+ button.
   Anynet+ devices connected to the TV are listed.
2.    Press the ▲ or ▼ button to select to a particular device and press the ENTER button. It is switched to the selected device.
.   If you cannot find a device you want, press the ▲ or ▼ button to select "Searching Connections", then press the ENTER button.
      The meassage "Configuring Anynet+ connection..." is displayed. When searching devices completes, the connected devices are listed in the Anynet+ menu.
    Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching operation.    The time required to scan for devices is determined by the number of con\
nected devices.     When the device scan is complete, the number of devices found are not di\
splayed.    Although the TV automatically scans devices when it is turned on using the POWER button, devices connected when the TV is already on are not displayed in the device list.  In this case, select the Searching Connections menu to search devices.    If you have selected external input mode by pressing the SOURCE button, you cannot use the Anynet+ function. Make sure to switch to an Anynet+ device by using the Anynet+ button.
Anynet+ Setup
Anynet+ (HDMI-CEC)  : Off
Auto Turn Off   : Off
Searching Connections 
EnterReturnMove
Off
On
EnterMove     
Recevier: OnConnect RecorderSetup
Air 28
Exit
Anynet+ Setup
Anynet+ (HDMI-CEC) : On
Auto Turn Off   : Off
Searching Connections 
EnterReturnMove
Off
On
EnterExitMove
Recevier: OnConnect RecorderSetup
Air 28
Anynet+ Setup
Anynet+ (HDMI-CEC) :   On  ►
Auto Turn Off  : On ►
Searching Connections       ►
EnterReturnMove

BN68-01308A-00Eng_0723.indd   792007-07-23   ¿ÀÈÄ 2:13:45 
						

							
English - 80
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV.
Anynet+ MenuDescription
View TVSwitches from Anynet+ to TV broadcast mode.
RecordStarts a recording. (This menu works only for a device supporting recording.)
(Device_Name) MenuShows the menu of the connected device.  Example: When a DVD Recorder is connected, the DVD Recorder’s title menu appears.
(Device_Name) OperationShows the play control menu of the connected device.  Example: When a DVD Recorder is connected, the play control menu of the DVD Recorder appears.
Connect (Device_Name)Your TV connects to the corresponding device.
ReceiverSound is output through the receiver (home theater).
SetupYou can set the Anynet+ (HDMI-CEC), auto turn off, and searching connections for using Anynet+.
TV  Remote Control Buttons Available in Anynet+ Mode
Device TypeOperating StatusAvailable Buttons
Anynet+ Device
After switching to the device, when the menu of the corresponding device is displayed on the screen.
Numeric buttons▲/▼/◄/►/ENTER buttonsColor buttonsEXIT button
After switching to the device, while playing a file
◄◄ (Backward search)►►(Forward search)(Stop)►  (Play/Pause)
Device with built-in TunerAfter switching to the device, when you are watching a TV programCH ▲/▼ button
Audio DeviceWhen Receiver is activatedVOL +/- buttonMUTE button
  The Anynet+ function only works when the active source on the TV remote control is set to TV.  The REC button works only while in the recordable state.    You cannot control Anynet+ devices using the buttons on the side of the TV. You can control Anynet+ devices only using the TV remote control.  The TV remote control may not work under certain conditions. In this case, r\
eselect the Anynet+ device.  The Anynet+ functions do not operate with other manufacturers’ products.  The ◄◄, ►► operations may differ depending on the device.
Recording You can make a recording of a TV program using a recorder.
Press the REC button.
Recording begins. (Only when the Anynet+ enabled recording device is connected.)
    You can record the source streams by selecting "Record" after pressing th\
e Anynet+ button.     Pressing the REC button will record whatever you are currently watching. If you are watc\
hing video from another device, the video from the device is recorded.     Before recording, check whether the antenna jack is properly connected t\
o the recording device. To properly connect an antenna to a recording device, refer to the recording devices users manu\
al.

BN68-01308A-00Eng_0723.indd   802007-07-23   ¿ÀÈÄ 2:13:45 
						

							
English - 81
Listening through a Receiver (Home theater) You can listen to sound through a receiver instead of the TV speaker.
1.   Press the Anynet+ button. Press the ▲ or ▼ button to select "Receiver", then press the ENTER button.
2.   Press the ◄ or ► button to select to "On", then press the ENTER button. Now you can listen to sound through the receiver.
. Press the EXIT button to exit.
    When the receiver (home theater) is set to On, you can hear sound outp\
ut from the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.    If your receiver supports audio only, it may not appear in the device list.    The receiver will work when you have properly connected the Optical IN j\
ack of the receiver to the Optical Out jack of the TV.    When using the WISELINK feature, sound may not output properly through t\
he receiver.    When listening through the receiver, there are restrictions for using the PIP and audio-related(MTS, Preferred language) menus.
Troubleshooting for Anynet+
 
SymptomSolution
Anynet+ does not work.■    Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.■ Connect only one receiver (home theater).■  Check if the Anynet+ device power cord is properly connected.■  Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.■  Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.■  Check whether the TV remote control is in TV mode.■  Check whether it is Anynet+ exclusive remote control.■  Anynet+ doesn’t work at a certain condition. (Searching channels, Operating\
 WISELINK)■  When connecting or removing the HDMI 1.3 cable, please make sure to searc h devices again or restart your TV.■  Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.■   Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.■    Press the TV button on the TV remote control to switch to TV. Then press the Anynet+ button to show the Anynet+ menu and select a menu you want.
I want to exit Anynet+.■   Select View TV in Anynet+ menu. ■    Press the SOURCE button on the TV remote control and select a device other than Anynet+ devices.■   Press any of CH, CH LIST, PRE-CH, and FAV.CH to change the TV mode.  (Note that the channel button operates only when a tuner-embedded Anynet+ device is not connected.)
The message Connecting to Anynet+ device... appears on the screen.
■   You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.■   Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet+ device does not play.You cannot use the play function when Plug & Play is in progress.
The connected device is not displayed.■ Check whether or not the device supports Anynet+ functions. ■   Check whether or not the HDMI 1.3 cable is properly connected.■  Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.■  Search Anynet+ devices again.■  You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables may not support Anynet+ functions.
The TV program cannot be recorded.Check whether the antenna jack on the recording device is properly connected.
The TV sound is not output through the receiver.Connect the optical cable between TV and the receiver.
EnterExitMove
Recevier:  OnConnect RecorderSetup
Air 28

BN68-01308A-00Eng_0723.indd   812007-07-23   ¿ÀÈÄ 2:13:45 
						

							
English - 82
Troubleshooting
If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips apply, call your nearest Samsung service center.
ProblemPossible Solution
Poor pictureTry another channel.Adjust the antenna.Check all wire connections.
Poor sound quality.Try another channel.Adjust the antenna.
No picture or sound.Try another channel.Press the SOURCE button.Make sure the TV is plugged in.Check the antenna connections.
No sound or sound is too low atmaximum volume.First, check the volume of units connected to your TV (digital broadcasting receiver, DVD, cable broadcasting receiver, VCR, etc.). Then, adjust the TV volume accordingly.
Picture rolls vertically.Check all wire connections.
The TV operates erratically.Unplug the TV for 30 seconds, then try operating it again.
The TV won’t turn on.Make sure the wall outlet is working.
Remote control malfunctionsReplace the remote control batteries.Clean the upper edge of the remote control (transmission window).Check the battery terminals.
“Check signal cable” message.Ensure that the signal cable is firmly connected to the PC source.
“Not Supported Mode” message.Check the maximum resolution and the frequency of the Video Adapter.Compare these values with the data in the Display Modes.
Digital broadcasting screenproblem.Please check the digital signal strength and input antenna.
The image is too light or too dark.Adjust the Brightness and Contrast.Adjust the Fine tuning.
Black bars on the screen.Make sure the broadcast you’re receiving is High Definition (HD).HD channels sometimes broadcast Standard Definition (SD) programming, which can cause black bars.Set your cable/satellite box to stretch or widescreen mode to eliminate the bars.
Picture has a Red/Green or  Pink tint.Make sure the Component cables are connected to the correct jacks.
Closed Captioning not working.If you are using a Cable/Satellite box, you must set Closed Captioning on the box,  not your TV.
Snowy pictureYour cable box may need a firmware upgrade. Please contact your Cable company.
Ghosting on pictureThis is sometimes caused by compatibility issues with your cable box.Try connecting Component cables instead.
Appendix

BN68-01308A-00Eng_0723.indd   822007-07-23   ¿ÀÈÄ 2:13:45 
						

							
English - 8
ProblemPossible Solution
Horizontal bars appear to flicker,jitter or shimmer on the image.Adjust the Coarse tuning and then adjust the Fine tuning.
Vertical bars appear to flicker,jitter or shimmer on the image.Adjust the Coarse tuning and then adjust the Fine tuning.
Screen is black and powerindicator light blinks steadily.On your computer check: Power, Signal Cable.The TV is using its power management system.Move the computer's mouse or press any key on the keyboard.
Image is not stable and may appear to vibrate when you have a computer connected to the PC input.
If the setting is not correct, use your computer utility program to change the display settings.Your TV supports multiscan display functions within the following frequency domain:
Horizontal frequency (kHz)30~60
Vertical frequency (Hz)60~75
PC Maximum refresh rate(at 60 Hz)1920 X 1080
Image is not centered on the screen.Adjust the horizontal and vertical position.The screen position must be adjusted on the output source (i.e. STB) with a digital signal.
The picture appears distorted in the corner of the screen.If Just Scan is selected with some external devices, the picture may appear distorted in the corner of the screen. This symptom is caused by the external devices, not TV.
The TFT LCD panel uses a panel consisting of sub pixels (6 220 800) which require sophisticated technology to produce. How-ever, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

BN68-01308A-00Eng_0723.indd   832007-07-23   ¿ÀÈÄ 2:13:45 
						

							
English - 84
Installing the Stand
< 2 ><  >
	1.	Place the TV face down on a soft cloth or cushion on a table.
2.	Put the stand into the hole at the bottom of the TV.
3.	Insert screw into the hole indicated and tighten.
Disconnecting the Stand
< 2 ><  >< 4 >
	1.	Place the TV face down on a soft cloth or cushion on a table.
2.	Remove four screws from the back of the TV.
3.	Separate the stand from the TV.
4.	Cover the bottom hole with a cap.

BN68-01308A-00Eng_0723.indd   842007-07-23   ¿ÀÈÄ 2:13:46 
						

							English - 85
TV Rear PanelAuto Wall-Mount
EX-LINK Cable (Not supplied)
Setup▲ MoreHDMI Black Level  : Low ►Film Mode : Off ►Wall-Mount Adjustment    ►PIP     ►Function Help  : On ►SW Upgrade    ►
TV
 Move   Enter Return
Once the auto wall mount is installed,  your TV’s position can be easily adjusted.
Auto Wall-Mount Adjustment (Sold separately)(LN-T4081F, LN-T4681F, LN-T5281F)
Entering the menu
1.   Press the ▲, ▼, ◄ or ► button on your remote control.  
The Wall Mount Adjustment screen is displayed.
   
If the Wall Mount Adjustment screen is not displayed when clicking on a direction button while watching your TV, use the menu to display that screen. 
 •  Press the  MENU butt on to display the menu. Press the ▲ or ▼ button to select 
“Setup”, then press the  ENTER button. 
 •  Press the ▲ or ▼ button to select “Wall-Mount Adjustment”, then press the 
ENTER button.
For installation, refer to the Installation Manual provided with the wall mount.
  For product installation and the installation and moving of the wall mount, make sure to consult a specialized installation company.
 
This installation manual is to be used when attaching the wall mount to a wall. When attaching to other building materials, please contact your nearest dealer.
The auto wall mount will not work when Anynet+
 is operating. 
Remembering the Position
2.   Adjust to the desired position using the ▲,▼,◄,► buttons.
  
If you press an arrow button when no OSD is displayed on the TV screen, the Adjustment screen appears.
  
Press the INFO button to reset. Press the ◄ or ► button to select “Yes”, then 
press the  ENTER button.   
The position is initialized to the default setting.
3.   Press the blue button. 
Press the ▲ and ▼ buttons to select a save mode from either Position 1,   
Position 2 or Position 3 in order to save the current position.
   To not save the current position, press the RETURN button. 
  
When selecting a save mode, you cannot use the Color buttons.
4.   Press the  ENTER button to save.
  
When Position1 is selected, the message "Current position saved as Position1" is displayed.
5.   Press the ENTER button.
  
The saved position appears on the left side of the OSD.
Moving to the remembered position
1.   Complete Step 1 of “Entering the menu”.
2.
    Pressing a Color (Red, Green, Yellow) button moves the auto wall mount to the saved position.
  
You can move the wall mount to one of the 3 pre-set positions by pressing the Red (Position 1), Green (Position 2) or Yellow (Position 3) buttons.
  
If you adjust the positon after moving to a pre-set position, the position display will disappear.
Save
Select a mode to Save.
Position1
Position2
Position3
 Adjust    Enter Return
Wall-Mount Adjusment
Adjust   Save  CenterINFOPosition  1   2    3
Wall-Mount Adjusment
Adjust   Save  CenterINFOPosition  1   2    3
Position1
BN68-01308A-00Eng_0730.indd   852007-07-30   �� 4:15:15 
						

							
English - 86
Wall Mount Kit Specifications (VESA)
Install your wall mount on a solid wall perpendicular to the floor.When attaching to other building materials, please contact your nearest \
dealer.If installed on a ceiling or slanted wall, it may fall and result in sev\
ere personal injury.
Product FamilyinchesVESA Spec. (A * B)Standard ScrewQuantity
LCD-TV
23~ 26200 * 100M4
4
32 ~ 40200 * 200M6
46 ~ 52600 * 400
M857 700 * 400 (No VESA)
57 ~ 70800 * 400
80 ~1400 * 800
PDP-TV
42 ~ 50600 * 400
M8
455 ~ 70800 * 400
63No VESA6
80 ~1400 * 8004
  Standard dimensions for wall mount kits are shown in the table above.
  
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
  
Do not use screws longer than the standard dimension, as they may cause damage to the inside of the TV set.
  
For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications.
  Do not use screws that do not comply with the VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the product or cause the product to fall, leading to personal injury.Samsung is not liable for these kinds of accidents.
  
Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
 Our 57" and 63" models do  not comply with VESA Specifications. Therefore, you should use our dedicated wall mount kit   for this model.
 Do not exceed 15 degrees tilt when mounting this TV.
Do not install your Wall Mount Kit while your TV is turned on.   It may result in personal injury due to electric shock

BN68-01308A-00Eng_0723.indd   862007-07-23   ¿ÀÈÄ 2:13:48 
						

							
English - 87
1.	Insert the locking device into the Kensington slot on the LCD TV (Figure 1) and turn it in the locking direction (Figure 2).
2.	Connect the Kensington lock cable.
3.	Fix the Kensington lock to a desk or a heavy stationary object.
Using the Anti-Theft Kensington Lock
The Kensington lock is a device used to physically fix the system when using it in a public place. The locking device  has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Please refer to the manual provided with the Kensington lock for proper use.
Figure 2
Figure 1
Cable

The location of the  Kensington Lock may be different depending on its model.

BN68-01308A-00Eng_0723.indd   872007-07-23   ¿ÀÈÄ 2:13:48 
						

							
English - 88
Specifications
Model NameLN-T4081F LN-T4681F
Screen Size (Diagonal)40 inches46 inches
PC Resolution1920 x 1080 @ 60 Hz1920 x 1080 @ 60 Hz
Sound Output 10W X 2 10W X 2
Dimensions (WxDxH) Body
With stand
 43.3 X 4 X 23.9 inches(1100 x 102.8 x 607.3 mm)43.3 X 11.4 X 26.6 inches(1100 x 289.9 x 675.4 mm)
 48.3 X 4.4 X 27 inches(1228 x 111 x 686.8 mm)48.3 X 12.6 X 29.6 inches(1228 x 319.9 x 752.4 mm)
Weight With Stand  Without stand
 57.76 lbs (26.2 kg) 49.16 lbs (22.3 kg)
 76.94 lbs (34.9 kg) 65.70 lbs (29.8 kg)
Environmental Considerations Operating Temperature Operating Humidity Storage Temperature Storage Humidity
  50 °F to 104 °F (10 °C to 40 °C) 10% to 80%, non-condensing -4 °F to 113 °F (-20 °C to 45 °C) 5% to 95%, non-condensing
  50 °F to 104 °F (10 °C to 40 °C) 10% to 80%, non-condensing -4 °F to 113 °F (-20 °C to 45 °C) 5% to 95%, non-condensing
Model NameLN-T281F LN-T781F
Screen Size (Diagonal)52 inches57 inches
PC Resolution1920 x 1080 @ 60 Hz1920 x 1080 @ 60 Hz
Sound Output 15W X 2 15W X 2
Dimensions (WxDxH) Body
With stand
 54 X 4.7 X 30.7 inches(1372 x 120 x 779.8 mm)54 X 12.6 X 33.3 inches(1372 x 319.9 x 845.4 mm)
 58 X 4.8 X 32.7 inches(1474 x 121 x 830.7 mm)58 X 13.6 X 35.3 inches(1474 x 344.7 x 895.4 mm)
Weight With Stand  Without stand
 92.59 lbs (42 kg) 81.13 lbs (36.8 kg)
 111.55 lbs (50.6 kg) 100.97 lbs (45.8 kg)
Environmental Considerations Operating Temperature Operating Humidity Storage Temperature Storage Humidity
  50 °F to 104 °F (10 °C to 40 °C) 10% to 80%, non-condensing -4 °F to 113 °F (-20 °C to 45 °C) 5% to 95%, non-condensing
  50 °F to 104 °F (10 °C to 40 °C) 10% to 80%, non-condensing -4 °F to 113 °F (-20 °C to 45 °C) 5% to 95%, non-condensing
Stand Swivel (Left / Right)
-20˚ ~ 20˚
Design and specifications are subject to change without prior notice.
This device is a Class B digital apparatus.
For the power supply and Power Consumption, refer to the label attached to the product.

BN68-01308A-00Eng_0723.indd   882007-07-23   ¿ÀÈÄ 2:13:49