Home > Ricoh > Printer > Ricoh Sp C410dn Service Manual

Ricoh Sp C410dn Service Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Ricoh Sp C410dn Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 127 Ricoh manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Ethernet Configuration
    69
    4
    Making Network Settings for Using Netware
    If you use NetWare, select the frame type for NetWare.
    Select one of the items below if necessary.
    Auto Select
    Ethernet II
     Ethernet 802.2
     Ethernet 802.3
     Ethernet SNAP
    Important
    ❒Usually, use the default setting ([Auto Select]). When you first select [Auto Se-
    lect], the frame type detected by the printer is adopted. If your network can
    use more than two frame types, the printer may fail to select the correct frame
    type if [Auto Select] is selected. In this case, select the appropriate frame type.
    APress the {Menu} key.
    BSelect [Host Interface] using {T} or {U}, and then press the {OK} key.
    CSelect [Network] using {T} or {U}, and then press the {OK} key.
    AQC001S
    Y M C K 
    						
    							Configuration
    70
    4
    DSelect [NW Frame Type] using {T} or {U}, and then press the {OK} key.
    ESelect the frame type using {T} or {U}, and then press the {OK} key.
    FPress the {Menu} key to return to the initial screen.
    GPrint a configuration page to confirm the settings made.
    Reference
    For details about printing the configuration page, see “Test Printing”,
    Quick Installation Guide. 
    						
    							IEEE 802.11b (Wireless LAN) Configuration
    71
    4 IEEE 802.11b (Wireless LAN) Configuration
    Configure the printer to use IEEE 802.11b (Wireless LAN). The following table
    shows the control panel settings and their default values. These items appear in
    the [Host Interface] menu.
    Note
    ❒To use IEEE 802.11b (Wireless LAN), select [IEEE 802.11b] for [LAN Type] in [Net-
    work] in the [Host Interface] menu, and then set the IP Address, Subnet Mask,
    Gateway Address, DHCP, Network Frame Type, and Effective Protocol un-
    der [Network]. For details about setting items under “Configuring the Printer
    for the Network”, see Software Guide.
    ❒The 802.11b interface unit cannot be used simultaneously with a standard
    ethernet interface.
    APress the {Menu} key.
    BSelect [Host Interface] using {T} or {U}, and then press the {OK} key.
    Setting Name Default Value
    Communication Mode   802.11 Ad hoc
    Channel  Inch version
    (1-11) 11
     Metric version
    (1-13) 13
    Communication Speed Auto
    SSID blank 
    WEP Off
    AQC001S
    Y M C K 
    						
    							Configuration
    72
    4
    CSelect [IEEE 802.11b] using {T} or {U}, and then press the {OK} key.
    DSelect [Communication Mode] using {T} or {U}, and then press the {OK} key.
    ESelect the transmission mode of IEEE 802.11b using {T} or {U}, and then
    press the {OK} key.
    The factory default is [802.11 Ad hoc].
     To use an IEEE 802.11b card for which the SSID (Network Name) setting is
    not necessary, select [Ad hoc].
     The transmission mode of IEEE 802.11b can also be set using a Web brows-
    er. For details, see Web browser, and “Configuring the Network Interface
    Board Using Web Browser”, Software Guide.
    FIf [802.11 Ad hoc] or [Ad hoc] is selected for [Communication Mode], set the chan-
    nel to use for transmission.
    Confirm the network administrator for the channel to use.
    GIn the [IEEE 802.11b] menu, select [Channel] using {T} or {U}, and then press
    the {OK} key.
    HEnter the channel using {T} or {U}, and then press the {OK} key. 
    						
    							IEEE 802.11b (Wireless LAN) Configuration
    73
    4
    ISet [Communication Speed] in the same way.
    The factory default is [Auto Select]. If you need to change the transmitting
    speed depending on environment you are using, select the appropriate trans-
    mitting speed.
    JPrint a configuration page to confirm the settings made.
    Reference
    For details about printing the configuration page, see “Test Printing”,
    Quick Installation Guide.
    Setting SSID
    If [Infrastructure] or [802.11 Ad hoc] is selected for [Communication Mode], set SSID to
    use for transmission.
    Confirm the network administrator for SSID to use.
    AIn the [IEEE 802.11b] menu, select [SSID Setting] using {T} or {U}, and then
    press the {OK} key.
    If an SSID has been set, you can check the SSID setting.
    BThe message “Enter SSID.” appears. Press [Text].
    CEnter characters using {T} or {U}, and then press the {OK} key.
    You can switch among upper/lower cases, numeric codes, and symbols by
    pressing [ABC/123].
    The characters that can be used are ASCII 0x20-0x7e (32 bytes).
    DPrint a configuration page to confirm the settings made. 
    						
    							Configuration
    74
    4
    Reference
    SSID can also be set using a Web browser. For details, see the Web Image
    Monitor Help, and “Configuring the Network Interface Board Using Web
    Browser”, Software Guide.
    WEP key can also be set using a Web browser. For details, see Web Image
    Monitor Help.
    For details about printing the configuration page, see “Test Printing”,
    Quick Installation Guide.
    Setting a WEP key
    In the case of using a WEP key on a network, activate the WEP setting to be used
    for communication along with WEP.
    Confirm the network administrator for the WEP Key to use.
    AIn the [IEEE 802.11b] menu, select [Security Type] using {T} or {U}, and then
    press the {OK} key.
    BSelect [WEP] using {T} or {U}, and then press [Details].
    When activating the WEP Setting, you will need to enter the WEP key. If you
    have not entered the key, be sure to enter it.
    CThe confirmation message appears. Press [Text]. 
    						
    							IEEE 802.11b (Wireless LAN) Configuration
    75
    4
    DEnter the characters using {V}, or {W}, and then press the {OK} key.
    You can switch among upper/lower cases, numeric codes, and symbols by
    pressing [ABC/123].
    When using 64 bit WEP, up to 10 characters can be used for hexadecimal and
    up to five characters for ASCII. When using 128 bit WEP, up to 26 characters
    can be used for hexadecimal and up to 13 characters for ASCII.
    The number of characters that can be entered is limited to 10 or 26 for hexa-
    decimal and 5 or 13 for ASCII.
    For ASCII character strings, each capital letter and lowercase letter is recog-
    nized respectively.
    EWhen entering characters is completed, press [Exit].
    FPress the {Menu} key to return to the initial screen.
    GPrint a configuration page to confirm the settings made.
    Reference
    WEP key can also be set using a Web browser. For details, see Web Image
    Monitor Help.
    For details about printing the configuration page, see “Test Printing”,
    Quick Installation Guide. 
    						
    							77
    5. Paper and Other Media
    Paper and Other Media Supported by This 
    Printer
    This section describes the paper size, feed direction, and the maximum amount
    of paper that can be loaded into each paper tray in this printer.
    Note
    ❒The following symbols and terminology are used to represent the feed direction.
    ❒Be careful of the paper feed direction. The direction is determined for each paper
    size.
    ❖Input Paper Sizes (Metric version)
    In this manual On the display Paper feed direction
    K ↑ (Feed direction)A4
    8 
    1/2 × 11Short-edge feed direction
    Feed Direction
    Size (mm)
    Bypass Tray
    Tray 1 
    Paper Feed Unit (Tray 2/3)
    A4K210 × 297
    B5 K182 × 257
    A5 
    *1 K148 × 210
    B6K128 × 182
    A6 
    *1 K105 × 148
    Legal (LG, 8
    1/2 × 14 inches)K216 × 356
    Letter (LT, 8
    1/2 × 11 inches) K216 × 279
    5
    1/2 × 81/2 inches *2 K140 × 216
    Executive (Exec., 7
    1/4 × 101/2 inches)K184 × 276
    Folio (8
    1/4 × 13 inches)K210 × 330
    Foolscap (F4, 8
    1/2 × 13 inches)K216 × 330
    F/GL (8 × 13 inches)K203 × 330 
    						
    							Paper and Other Media
    78
    5
    *1The size cannot be set automatically if you use the following model: *2The size cannot be set automatically if you use the following model: 
     
    The size is supported and the printer selects it automatically.
    
    The size is supported, but it should be selected using the control panel.
    
    The size is supported, but it should be set as a custom size using the control
    panel.
    The supported size may differ depending on the printer language you use.
    Set as a custom size setting using the control panel.
    The following sizes are supported:
     Tray 1: approximately 100 - 216 mm in width, and 148 - 355.6 mm in
    length.
     Bypass Tray: approximately 70 - 216 mm in width, and 140 - 900 mm in
    length.
     Paper Feed Unit (Tray 2/3): approximately 100 - 216 mm in width, and
    210 - 355.6 mm in length.
     
    The size is not supported.
    Com#10 Env (4 1/8 × 9 1/2 inches)K104.8 × 241.3
    C5 Env (6.38 × 9.02 inches)K162 × 229
    C6 Env (4.49 × 6.38 inches)K114 × 162
    DL Env (4.33 × 8.66 inches)K110 × 220
    Monarch Env (3 
    7/8 × 7 1/2 inches)K98.4 × 190.5
    Custom Size - -
    16K (7.68 × 10
    1/2 inches)K195 × 267
    Feed Direction
    Size (mm)
    Bypass Tray
    Tray 1 
    Paper Feed Unit (Tray 2/3) 
    						
    All Ricoh manuals Comments (0)

    Related Manuals for Ricoh Sp C410dn Service Manual