Ricoh Sp C410dn Service Manual

							Attaching IEEE 1284 Interface Board Type A
39
2 Attaching IEEE 1284 Interface Board Type A
R CAUTION:
Important
❒Before handling the 1284 interface board, touch something metal to discharge
static electricity. Static electricity thing damage the 1284 interface board.
❒Do not subject the 1284 interface board to physical shocks.
ACheck the package contains the following:
❖IEEE 1284 Interface Board Type A
BTurn off the power, and then unplug the power cable.
CLoosen the two screws and remove the cover of the 1284 interface board in-
stallation unit.
The removed cover is not used when installing the 1284 interface board. Do not touch inside the controller board compartment. Doing so may cause 
a machine malfunction or a burn.
ABT041S1
AQC091S 
						

							Installing Options
40
2
DFully insert the 1284 interface board.
Confirm that the 1284 interface board is firmly connected to the controller
board.
ETighten the two screws to secure the 1284 interface board.
Note
❒Use the supplied adaptor to make the connection with the computer.
❒After finishing installation, you can check the 1284 interface board is prop-
erly installed: Print the configuration page from the [List/Test Print] menu.
If it is installed properly, “Parallel Interface” will appear for “Device Con-
nection” on the configuration page.
❒If the 1284 interface board is not installed properly, reinstall it following
this procedure. If you cannot install it properly even after attempting rein-
stallation, contact your sales or service representative.
Reference
For printing the configuration page, see “Test Printing”, Quick Installation
Guide.
AET102S
AQC103S 
						

							Attaching the USB Host Interface Board Type A
41
2 Attaching the USB Host Interface Board 
Type A
Important
❒When connecting a digital camera to the printer via USB, the USB port of the
USB host interface board is required.
❒Before handling the USB host interface board, ground yourself by touching
something metal to discharge any static electricity. Static electricity can dam-
age the USB host interface board.
❒Do not subject the USB host interface board to physical shocks.
ACheck the contents of the box.
❖USB Host Interface Board
BTurn off the power, and then unplug the power cable.
CLoosen the two screws and remove the cover of the USB host interface
board installation unit.
The removed cover is not used when installing the interface unit.
AQC041S
AQC910S 
						

							Installing Options
42
2
DFully insert the USB host interface board.
ETighten the two screws to secure the USB host interface board.
Check the USB host interface board is inserted firmly to the controller board.
Note
❒After finishing installation, check the USB host interface board is installed
properly: print the configuration page from the [List/Test Print] menu. If it
is installed properly, you will see “USB Host” for “Device Connection” on
the configuration page.
❒If the USB host interface board is not installed properly, reinstall it follow-
ing this procedure. If you cannot install it properly even after attempting
reinstallation, contact your sales or service representative.
❒You can connect the USB cable from a digital camera to the USB host inter-
face board. For details, see p.59 “Connecting a digital camera”, or Software
Guide.
Reference
For details about printing the configuration page, see “Test Printing”,
Quick Installation Guide.
AQC042S
AQC044S 
						

							Attaching Gigabit Ethernet Board Type A
43
2 Attaching Gigabit Ethernet Board Type A
Important
❒The printers ethernet and USB ports are not available when the gigabit eth-
ernet board is attached to the printer. Instead, you can use the ethernet port
and USB port mounted on the board.
❒Before handling the gigabit ethernet board, ground yourself by touching
something metal to discharge any static electricity. Static electricity can dam-
age the gigabit ethernet board.
❒Do not subject the gigabit ethernet board to physical shocks.
ACheck the contents of the box.
❖Gigabit Ethernet Board
❖Protective caps (one each for the ethernet port and the USB port)
❖Ferrite core (This printer does not require the ferrite core.)
Note
❒Design of the ferrite core varies according to printer model.
AGY096S
AGY097S
AQC092S 
						

							Installing Options
44
2
BTurn off the power, and then unplug the power cable.
CDisconnect the cables from the ethernet port and the USB port of the print-
er, and cover each port with its protective cap.
DLoosen the two screws and remove the cover of the Gigabit ethernet board
installation unit.
The removed cover is not used when installing the interface unit.
EFully insert the Gigabit ethernet board.
AQC046S
AQC091S
AQC043S 
						

							Attaching Gigabit Ethernet Board Type A
45
2
FTighten the two screws to secure the Gigabit ethernet board.
Check the Gigabit ethernet board is connected firmly to the controller board.
Note
❒After finishing installation, check the Gigabit ethernet board is installed
properly: print the configuration page from the [List/Test Print] menu. If it
is installed properly, you will see “Gigabit Ethernet Board” for “Device
Connection” on the configuration page.
❒If the Gigabit ethernet board is not installed properly, reinstall it following
this procedure. If you cannot install it properly even after attempting rein-
stallation, contact your sales or service representative.
❒You need to make settings with the control panel before using the gigabit
ethernet board. For details, see p.63 “Ethernet Configuration”.
Reference
For details about printing the configuration page, see “Test Printing”,
Quick Installation Guide.
AQC045S 
						

							Installing Options
46
2
Attaching Data Overwrite Security Unit Type E
Important
❒Protect the Data Overwrite Security unit from physical shocks.
❒Use the right slot for the Data Overwrite Security unit.
ACheck the package contains the following:
❖Data Overwrite Security unit
BTurn off the power, and then unplug the power cable.
CRemove the cover of the controller boards central expansion card slot.
DCarefully insert the Data Overwrite Security unit, until the card clicks into
place.
AET104S
AQC105S
AQC106S 
						

							Attaching Data Overwrite Security Unit Type E
47
2
EReattach the cover over the Data Overwrite Security unit. Fasten the screw
to secure the cover.
Note
❒Do not touch the Data Overwrite Security unit while the printer is in use.
It may come loose, even if pushed only slightly.
AQC107S 
						

							Installing Options
48
2Attaching the Camera Direct Print Card
Important
❒Protect the Camera Direct Print card from physical shocks.
❒Use the right slot for the Camera Direct Print card.
ACheck the package contains the following:
❖Camera Direct Print Card
BTurn off the power, and then unplug the power cable.
CRemove the cover of the controller boards center expansion card slot.
DCarefully insert the Camera Direct Print card, until the card clicks into place.
AET104S
AQC105S
AQC106S