Ricoh Sp C410dn Service Manual

							Connecting a digital camera
59
3 Connecting a digital camera
This printer supports direct printing, which allows you to print images taken
with digital cameras without using a computer. The following describes how to
connect the printer to a digital camera.
Important
❒This function requires the following optional units:
 USB Host Interface Board Type A (Optional Interface Unit)
 Camera Direct Print Card Type B (Expansion Card)
❒The USB host interface board is supplied with a USB cable and a hook onto
which you can roll up and hang the cable.
❒Make sure your digital camera supports PictBridge.
AAttach the hook on the back of the printer near the USB connection slot.
Attach the hook where it will not interfere with printer operation and access.
BCheck the printer and the digital camera are both switched on.
AQC047S
AQC050S 
						

							Connecting the Printer
60
3
CUse the USB cable supplied with the USB host interface board to connect
the printer and the digital camera. Connect the flat connector of the USB ca-
ble to the USB host interface board.
DConnect the square-shaped connector on the opposite end of the USB cable
to the digital camera.
ESecure the USB cable using the hook.
Reference
For details about attaching the USB host interface board, see p.41 “Attach-
ing the USB Host Interface Board Type A”.
For details about attaching the Camera Direct Print card, see p.48 “Attach-
ing the Camera Direct Print Card”.
For details about direct printing, see “Direct Printing from digital camera
(PictBridge)”, Software Guide.
AQC063S
AQC049S 
						

							Parallel Connection
61
3 Parallel Connection
Important
❒The parallel interface cable is not supplied with the printer.
❒The printers parallel connection is a standard bidirectional interface that re-
quires an IEEE 1284-compliant 36-pin parallel cable and host computer paral-
lel port.
❒Use shielded interface cable. Unshielded cables create electromagnetic inter-
ference that could cause malfunctions.
ATurn off the printer and computer.
BConnect the cable to the interface socket of the IEEE 1284 interface board.
Important
❒Voltage rating of the computers parallel port: DC 5 V (max.)
CSecurely attach the other end of the parallel cable to your computers paral-
lel port. Secure the cable.
Reference
For details about settings for parallel connection printing, see Software
Guide.
AKQ010S 
						

							Connecting the Printer
62
3 
						

							63
4. Configuration
Ethernet Configuration
Make the following network settings according to the network interface you are
using.
You can use SmartDeviceMonitor for Admin or a Web browser to make IP ad-
dress-related settings in a TCP/IP-capable environment.
Important
❒Configure the printer for the network using the control panel.
❒The following table shows the control panel settings and their default values.
These items appear in the “Host Interface” menu.
Note
❒If [Auto-Obtain (DHCP)] is in use, the IP address, subnet mask, and gateway ad-
dress are all set automatically.
❒Make this setting only when it is necessary. See Software Guide.
Setting Name Value
Auto– Obtain (DHCP) On
IPv4 Address 011.022.033.044
Subnet Mask 000.000.000.000
Gateway Address 000.000.000.000
Frame Type (NW) Auto
Effective Protocol  IPv4:
Effective
IPv6:
Effective
 NetWare:
Effective
SMB:
Effective
 AppleTalk:
Effective
Ethernet Speed Auto
LAN Type Auto 
						

							Configuration
64
4
APress the {Menu} key.
BSelect [Host Interface] using {T} or {U}, and then press the {OK} key.
CSelect [Network] using {T} or {U}, and then press the {OK} key.
DSelect [Effective Protocol] using {T} or {U}, and then press the {OK} key.
ESelect the network protocol using {T} or {U}, and then press the {OK} key.
AQC001S
Y M C K 
						

							Ethernet Configuration
65
4
FSelect [Effective] or [Invalid] using {T} or {U}, and then press the {OK} key.
Set other protocols you need to set in the same way.
Select [Invalid] for unused protocols.
 Enable IPv4 to use the Pure IPv4 environment of NetWare 5/5.1, NetWare
6/6.5.
GPress the {Escape} key until the screen returns to the [Network] menu.
HIf you use IPv4, assign the IPv4 address to the printer. Select [Machine IPv4
Address] using {T} or {U}, and then press the {OK} key.
To get the IP address for the printer, contact your network administrator.
ITo specify the IP Address, press [IP Add.].
If you use IPv4, assign also Subnet Mask and Gateway Address. To assign
these, press [Subnet M] or [Gateway] instead.
JEnter the address using {T} or {U}, and then press the {OK} key.
Press the {T} or {U} key to enter the left most entry field of the address. After
entering the left field, press the {V} key, and then you can enter the next field.
After completing to enter in the all fields, press the {OK} key. Use this method
to assign Subnet Mask and Gateway Address.
 Do not set “011.022.033.044” as the IP address. 
						

							Configuration
66
4
KSelect [Specify] using {T} or {U}, and then press the {OK} key.
If you do not select [Specify] in this step, the address you set will not be saved.
LPress the {Menu} key to return to the initial screen.
MPrint a configuration page to confirm the settings made.
Reference
For details about printing the configuration page, see “Test Printing”,
Quick Installation Guide. 
						

							Ethernet Configuration
67
4
Using DHCP - Detecting the Network Address Automatically
Important
❒When you use this printer in DHCP environment, select [Auto-Obtain (DHCP)]
following this procedure.
❒When [Auto-Obtain (DHCP)] is selected, you cannot make settings for the fol-
lowing items:
 IP Address
Subnet Mask
 Gateway Address
❒Consult your network administrator for information about making network settings.
APress the {Menu} key.
BSelect [Host Interface] using {T} or {U}, and then press the {OK} key.
CSelect [Network] using {T} or {U}, and then press the {OK} key.
DSelect [Machine IPv4 Address] using {T} or {U}, and then press the {OK} key.
AQC001S
Y M C K 
						

							Configuration
68
4
ESelect [Auto-Obtain (DHCP)] using {T} or {U}, and then press the {OK} key.
The address detected by the printer will appear.
To check the detected addresses, press the followings:
[IP Add.]
IP address
[Subnet M]
Subnet Mask
[Gateway]
Default Gateway
FPress the {Menu} key to return to the initial screen.
GPrint a configuration page to confirm the settings made.
Reference
For details about printing the configuration page, see “Test Printing”,
Quick Installation Guide.