Ricoh Sp C410dn Service Manual

							9
2. Installing Options
Available Options
This section describes how to install options.
By installing options, you can improve the printer performance and have an ex-
panded variety of features to use. For the specifications of each option, see p.182
“Specifications”.
R CAUTION:
Important
❒The voltage rating of the connector for options is 24 V DC or less.
Option List
The following is a list of options for this printer.•Before installing options, the machine should be turned off and unplugged 
for at least an hour. Components inside the machine become very hot, and 
can cause a burn if touched.
Before moving the machine, unplug the power cable from the outlet. If the 
cable is unplugged abruptly, it could become damaged. Damaged plugs or 
cables can cause an electrical or fire hazard.
When lifting the machine, use the grips on both sides. The machine could 
break or cause an injury if dropped.
The 25 ppm model printer The 30 ppm model printer
Paper Feed Unit Type 4000 Available Available
Hard Disk Drive Type 4000  Available Available
Memory Unit Type D 128MB  Available Available
Memory Unit Type E 256MB  Available Available
IEEE 802.11b Interface Unit  Available Available
IEEE 1284 Interface Board Type A Available Available
Bluetooth Interface Unit Type 3245 Available Available
User Account Enhance Unit Type E Available Available
USB Host Interface Board Type AAvailable Available
Gigabit Ethernet Board Type A Available Available
Camera Direct Print Card Type BAvailable Available
 Data Overwrite Security Unit Type EAvailable Available
VM Card Type D Available Available
Data Storage Card Type A Available Available 
						

							Installing Options
10
2
Option Installation Flow Chart
Installing multiple options in the following order is recommended:
AAttach the paper feed unit (Paper Feed Unit Type 4000).
Attach the paper feed units to the bottom of the printer.
You can attach up to two paper feed units. Up to 1750 sheets of paper can be
loaded in total.
BInstall the SDRAM module (Memory Unit Type D 128MB, Memory Unit
Type E 256MB).
Install the module to the SDRAM module slot on the controller board.
There are two types of memory unit: 128 MB and 256 MB.
CInstall User Account Enhance Unit (User Account Enhance Unit Type E).
Install the module to the User Account Enhance Unit slot of the controller
board.
DInstall the hard disk drive (Hard Disk Drive Type 4000).
Install the hard disk drive to the controller board.
EInstall the IEEE 1284 interface board, IEEE 802.11b interface unit, Bluetooth
interface unit, USB host interface board, or Gigabit Ethernet board.
Install the IEEE 1284 interface board, IEEE 802.11b interface unit, Bluetooth
interface unit, USB host interface board, or Gigabit Ethernet board on the con-
troller board.
Up to two of the followings can be installed:
 IEEE 1284 Interface Board Type A 
 IEEE 802.11b Interface Unit 
 Bluetooth Interface Unit Type 3245 
 USB Host Interface Board Type A
 Gigabit Ethernet Board Type A
FInstall the security unit (Data Overwrite Security Unit Type E, Data Storage
Card Type A), the Camera Direct Print card (Camera Direct Print Card Type
B), or the VM card (VM Card Type D).
Insert these units into the SD card slot on the controller board. 
						

							Available Options
11
2
Installing Options
Install options in the positions shown in the illustration.
❖Exterior
1. Paper Feed Unit Type 4000 
Loads up to 550 sheets of paper. 
Up to two paper feed units, can be in-
stalled on the printer. Installed tray
units are identified as “Tray 2” and
“Tray 3”.
See p.14 “Attaching Paper Feed Unit
Type 4000”.
AET061S 
						

							Installing Options
12
2
❖Interior
1.Memory Unit Type D 128MB/Mem-
ory Unit Type E 256MB (SDRAM mod-
ule)
Install 128 MB or 256 MB SDRAM
module into the controller board slot.
See p.17 “Attaching Memory Unit
Type D 128MB, Memory Unit Type E
256MB (SDRAM Module)”.
2.Optional boards
See p.33 “Attaching IEEE 802.11b In-
terface Unit”.
See p.36 “Attaching Bluetooth Inter-
face Unit Type 3245”.
See p.39 “Attaching IEEE 1284 Inter-
face Board Type A”.
See p.41 “Attaching the USB Host In-
terface Board Type A”.
See p.43 “Attaching Gigabit Ethernet
Board Type A”.
3.Optional units
See p.46 “Attaching Data Overwrite
Security Unit Type E”.
See p.48 “Attaching the Camera Direct
Print Card”.
See p.50 “Attaching VM Card Type
D”.
See p.52 “Attaching Data Storage
Card Type A”.
4.Hard Disk Drive Type 4000
See p.27 “Attaching Hard Disk Drive
Type 4000”.
5.User Account Enhance Unit Type E 
See p.22 “Attaching User Account En-
hance Unit Type E”.
Note
❒You can have two of the following types of extension board installed at the
same time: IEEE 802.11b Interface Unit, Bluetooth Interface Unit Type 3245,
IEEE 1284 Interface Board Type A, USB Host Interface Board Type A, and Gi-
gabit Ethernet Board Type A.
❒Some printer models come with the Expansion Hard Disk Drive Unit and
Data Overwrite Security Unit installed as default.
Reference
For the specifications of each option, see p.182 “Specifications”.
AQC040S 
						

							Available Options
13
2
Caution when re-installing the controller board
This section describes handling the controller board when installing options.
If you slide out the controller board to install the SDRAM module, the user ac-
count enhance unit, or the printer hard disk, carefully follow the instruction be-
low to re-install the controller board.
 Re-install the controller board into the printer by pushing the bottom center
area of the board, as shown in the illustration.
Important
❒The following may occur if the controller board is not properly installed:
 all control panel indicators are lit.
 no control panel indicators is lit.
 the “SC670” error message appears on the display.
AQC004S 
						

							Installing Options
14
2Attaching Paper Feed Unit Type 4000
When installing multiple options, install the paper feed unit first.
R CAUTION:
R CAUTION:
Important
❒Up to two paper feed units can be attached to the printer.
❒When two paper feed units are installed, they are detected as “Tray 2” and
“Tray 3” starting from the upper unit.
❒Before using the new paper feed unit, you must make settings in the printer
driver.
❒Check the printer nameplate to confirm the model code.
ACheck the package contains the following:
❖Paper Feed Unit (including a paper tray)
BTurn off the power, and then unplug the power cable.
CRemove the orange fastening tapes from the paper feed unit. The printer weights approximately 50 kg (110.3 lb.). When moving the print-
er, use the inset grips on both sides, and lift slowly. The printer will break or 
cause injury if dropped.
Lifting the paper feed unit carelessly or dropping it may cause injury.
AET108S 
						

							Attaching Paper Feed Unit Type 4000
15
2
DLift the printer using the inset grips on both sides of the printer.
Important
❒The printer should always be lifted by at least two people.
EAlign the printer with the two upright pins on the paper feed unit and then
lower the printer slowly.
When installing two paper feed units, connect the two units first using the
same procedure below before connecting the units to the printer.
AQC031S
AET074S
AET075S 
						

							Installing Options
16
2
Note
❒When moving the printer, remove the paper feed unit.
❒After finishing installation, you can check whether the paper feed unit is
properly installed: Print the configuration page from the [List/Test Print]
menu. If it is installed properly, “Tray 2” or “Tray 2”, “Tray 3” will appear
for “Connection Equipment” on the configuration page.
❒If the paper feed unit is not installed properly, reinstall it following this
procedure. If you cannot install it properly even after attempting reinstal-
lation, contact your sales or service representative.
Reference
For printing the configuration page, see “Test Printing”, Quick Installation
Guide.
For loading paper onto the paper tray, see p.89 “Loading Paper”.
When adjusting the printing position, see p.152 “Adjusting Tray Registra-
tion”. 
						

							Attaching Memory Unit Type D 128MB, Memory Unit Type E 256MB (SDRAM Module)
17
2 Attaching Memory Unit Type D 128MB, 
Memory Unit Type E 256MB (SDRAM Module)
R CAUTION:
Important
❒Before touching the memory unit, ground yourself by touching something
metal to discharge any static electricity. Static electricity can damage the
memory unit.
❒Do not subject the memory unit to physical shocks.
❒Available memory varies depending on a model type.
❒Before using the new memory unit, Be sure to make settings in the printer
driver.
ATurn off the power, and then unplug the power cable.
BLoosen the three screws securing the controller board. 
The screws cannot be fully removed. Do not touch the inside of the controller board compartment. Doing so may 
cause a malfunction or a burn.
AQC630S 
						

							Installing Options
18
2
CGrasp the handles and carefully pull out the controller board.
Using both hands, slide the controller board completely out.
DPlace the controller board on a flat surface, and then loosen the four screws
to remove the cover.
The screws cannot be fully removed.
AQC640S
AQC650S
AQC660S