Ricoh Mp 7500 Service Manual

Changing the Paper Size
75
5
Changing to a Size that is Not Automatically Detected
If you load a paper size that is not selected automatically, you need to specify the
paper size with the control panel. This section explains how to load these paper
taking 11”× 15”L as an example.
Important
❒Following paper sizes that are not selected automatically.
 11”×15”L, 11”×14”L, 10”×15”L, 8
1/4”×14”L, 8”×101/2”L, 210×340L,
210×182K, 210×170K
APress the {User Tools/Counter} key.
BPress [System Settings].
CPress...

Adding Paper, Toner and Staples
76
5
DSelect the tray for which you want to change the paper settings.
Press either of [Tray Paper Size: Tray 2] to [Tray Paper Size: Tray 4].
ESelect the loaded paper size and feed direction, and then press [OK].
The set paper size and feed direction is displayed.
FPress the {User Tools/Counter} key.
The initial display is shown.
Note
❒If you want to print on paper that is selected automatically after printing
on a paper size that is not selected automatically, you must...

Adding Toner
77
5 Adding Toner
This section explains adding and storing toner.
R WARNING:
R CAUTION:
R CAUTION:
R CAUTION:
R CAUTION:
R CAUTION:
R CAUTION:
Important
❒Fault may occur if you use toner other than the recommended type.
❒When adding toner, do not turn off the operation switch. If you do, settings
will be lost.
❒Always add toner when the machine instructs you.
❒When a message “
D Add Toner” is shown on the display, replace the toner.
❒Store toner containers in a cool, dry place free from...

Adding Paper, Toner and Staples
78
5
Note
❒You can still make about 1000 copies after the messages “D Toner Car-
tridge is almost empty.
” and “Replace Toner Cartridge.” appear cy-
clically, but replace toner early to prevent poor copy quality.
❒You can check name of the required toner name and the replacement proce-
dure using the “
D Add Toner” screen.
❒Press [System Status] to check contact number for consumables order. For sys-
tem status, see p.5 “Checking Machine Status and Settings”.
Inserting...

Adding Staples
79
5 Adding Staples
This section explains what to do when staples need replacing.
Important
❒Stapling failures or jams may occur if you use a staple cartridge other than
that recommended.
Refill the stapler according to the finisher type. (Check the type if you are un-
sure.) For details about type of finisher, see “Options”, About This Machine.
3,000 Sheet-50 Sheet Staple Finisher and Booklet Finisher
The following procedure explains how to add staples to the 3,000 Sheet-50 Sheet
Staple...

Adding Paper, Toner and Staples
80
5
3,000 Sheet-100 Sheet Staple Finisher
The following procedure explains how to add staples to the 3,000 Sheet-100
Sheet Staple Finisher.
ANS048S 

Adding Staples
81
5
Booklet Finisher (Saddle Stitch)
The following procedure explains how to add staples to the Booklet Finisher.
ANS060S 

Adding Paper, Toner and Staples
82
5 

83
6. Clearing Misfeeds
This chapter explains what to do when paper or originals misfeed (become
jammed inside the machine).
Removing Jammed Paper
R CAUTION:
R CAUTION:
Important
❒When clearing misfeeds, do not turn off the operation switch. If you do, your
copy settings will be lost.
❒To prevent misfeeds, do not leave any torn scraps of paper inside the ma-
chine.
❒Contact your service representative if misfeeds occur frequently.
Note
❒For details about how to locate and remove misfeeds, see “Locating...

Clearing Misfeeds
84
6
Locating Jammed Paper
If a misfeed happens, remove the misfed paper or original following the proce-
dures stated on the sticker on the rear of main unit front cover.
A misfeed has occurred in the place corresponding to the letter displayed on the
control panel.
ANS101S