Panasonic Video Multiplexer Wj Fs616c Operating Instructions

72
3. Press the [ZOOM] button to adjust the lens zoom to
achieve the desired image while observing the active
monitor.
Press this button to the [TELE] position to optically bring
an object closer. 
Pressing to the [WIDE] position has the reverse effect.
4. Press the [IRIS CLOSE/OPEN] buttons to close/open
the lens iris. Adjust the lens iris by pressing these but-
tons to obtain the proper image exposure.
Pressing these buttons at the same time will reset the
lens iris to the factory default setting....

73
3. Select the desired item by moving the joystick UP or
DOWN, and then select the desired mode by moving
the joystick LEFT or RIGHT.
4. Press the [CAM(SET)] button to execute the setting or
enter a submenu.
5. Press the [F3] button to reset the selected item parame-
ter, or press the [F4] button to reset all functions to the
factory default setting.
6. Press the [MON(UNIT/ESC)] button to execute the set-
ting and returns to the previous setup menu.
7. Press the [CAMERA SET OFFB] button to exit from...

74
Auxiliary Control
The following function is available only with a system that
includes WV-RC100 or WV-RC150 Receivers.
1. Select the desired monitor and camera referring to the
Camera Selection procedure described above.
2. While the ALT indicator is on, press the [HOME/–] or
[AUTO/+] button to toggle the user’s auxiliary switch in
the receiver on and off.
Note:The auxiliary control is not available while operat-
ing the zoom or pan/tilt head.
Alarm Control Function
Alarm Suspension
This function...

75
The system shown below is an example of the expansion capabilities of the WJ-FS616C video multiplexer.
Up to four video multiplexers can be connected to expand the camera inputs.
SYSTEM EXPANSION
481216
371115
261014
15913
PUSH   OPEN16POWERLOCKON
OFF
ALARMMULTI
SCREENMULTISCREENSELECT
RESET SPOT SEQUENCE
VCR
CAMCAMERA/PRESET   P O S I T I O N
Video
Data RS-485
Spot In
Time Lapse VCR
System Controller
WV-CU550C
Spot Monitor
Live
Main: 1-16ch
Local: 1-16chMultiscreen Monitor
Live 1-16ch
Playback...

76
Connections
In this type of installation, only one video multiplexer is con-
nected directly to the system controller by a control cable.
The rest of the video multiplexers are connected to the sys-
tem controller in a daisy-chain type connection.
Refer to the connections and data port settings shown
below.
Notes:
• Up to four video multiplexers can be daisy-chained
to the system controller.
• Unit numbers should be assigned in the order of
connection, starting with the unit connected directly
to the...

77
Application 2
The camera images in the Local Site (Unit 2) can be dis-
played on the multiscreen monitor in the Main Site (Unit 1)
by connecting a coaxial cable shown below.
For Local Site
• Confirm that the REC MODE SETUP in the REC
OUTPUT SETUP menu (page 33) is set to MODE 0.
If the another mode is set for the REC MODE
SETUP, this application does not work properly.
For Main Site
• To display the camera images in the Local Site,
operate the video multiplexer as displaying the
playback image....

78
APPENDIX
(02H)   (      ) – – – – – –  (      )   (3AH)   (      ) – – – (      )     (03H)
[STX]     [Transmission Command]     [:]     [Error Code]     [ETX]
[STX]   [Address] [;]   [Transmission Command]   [ETX] Code
ASCII (02H)   (      ) – – – – – – – – – – – – – – – – – (      )   (03H)
[NAK]   [e] Code
ASCII (15H)
This Appendix details the elements for communication between the Video Multiplexer and the personal computer. For BAUD
RATE, DATA BIT, STOP BIT and PARITY settings, see page 42 COM...

79
m=0Quad m=1 7 divide
m=2 9 divide m=3 10 divide
m=4 13 divide   m=5 16 divide
m=
1No. of divisions (+)m=DNo. of divisions (−)
Item Item
m=0
Manual Reset
m=1 Auto Reset mm=00 - 16   Camera Number
*00=Spot Input
mm=01 - 16   Playback CH number
Alarm InputResponse
Command (ASCII)
Command Table
(1) Operation Control
Transmission
Command (ASCII)Parameter (ASCII)
Monitor Select OMS : m OMSm=0
Spot Monitor
m=1 Multiscreen Monitor
m=2 Multiscreen 2 Monitor
VCR/Camera Select OVC : m OVCm=0
Camera Mode
m=1 VCR...

80
Item
Item
Response
Command (ASCII) Transmission
Command (ASCII)Parameter (ASCII) DCR : mm mm=UU Move Upward
mm=DD Move Downward
mm=RR Move to Right
mm=LL Move to Left
mm=BB Move to lower layer
mm=ES Move to upper layer
Item decision (partial)
mm=IC Select parameter (+)
mm=DC Select parameter (–)
mm=FF Select page
mm=UR Move to Upper-Right
mm=UL Move to Upper-Left
mm=DR Move to Lower-Right
mm=DL Move to Lower-Left
*2 DCR (3) Cursor Control
Cursor Movement
Select Parameter
*2 The parameter valid on the...

81
No. Examples of response
Response Command (ASCII) Main Unit Information
1 @mPLSNcc Single Spot (Camera)
2 @mPLSZcc Single Spot + Electronic Zoom (Camera)
3 @mPLSScc Single Spot + Still (Camera)
4 @mPLSXcc Single Spot + Zoom + Still (Camera)
5 @mPLSMLa Multi Spot (+ Still) (Camera)
6 @mPLQNcc Spot Sequence (Camera)
7 @mPLQMLa Multi Sequence (Camera)
8 @mPLQZcc Spot Sequence + Zoom (Camera)
9 @mPVSNcc Single Spot (VCR)
10 @mPVSZcc Single Spot + Zoom (VCR)
11 @mPVSScc Single Spot + Still (VCR)
12...