Panasonic Video Multiplexer Wj Fs616c Operating Instructions

61
Alarm Reset
Manual Reset
When an alarm is activated, the ALARM indicator blinks.
The indicator keeps blinking until all alarms are cleared by
pressing the [ALARM RESET] button.
The blinking or lit indicator goes off.
Auto Reset
The alarm is automatically reset after the programmed
alarm output time has elapsed or the lost video signal has
been recovered.
The ALARM indicator changes from blinking to a steady
light.
Pressing the [ALARM RESET] button will clear the alarm
and switch the indicator off....

62
Alarm Suspension
This function disables activation of the alarm link and
instead enables storing of any alarm activated in the alarm
log.
It is used to suspend the alarm link during camera setup.
To suspend the alarm:
1. Press the [RESET] and [SPOT] buttons at the time for 2
seconds or more to suspend the alarm.
The indicator in the [RESET] button lights.
2. Press the [RESET] button to reset the alarm suspension.
The indicator in the [RESET] button goes off.
RESET SPOT 

63
Recording on the Time Lapse VCR
The following selections are made in the WJ-FS616C
SETUP MENU described previously.
Refer to the Recording Mode Setup on page 33 for further
details.
1. Check the selected recording mode (MODE 0 - MODE
9).
MODE 0:Normal Mode (Real Time)
MODE 1 - 9:Time Lapse Mode (Linear Mode)
If MODE 9 is selected, check the image (spot or
quad) to be recorded on the VCR.
2. Press the Record button of the VCR to begin recording.
Notes:
• To let the VCR display the VCR menu for setup,...

65
OPERATING PROCEDURES
(with WV-CU550C) 

66
The WJ-FS616C video multiplexer can be controlled from the WV-CU550C system controller.
The following procedures apply when the WV-CU550C system controller is connected to the system.
Major Operating Controls and Their Functions
Note:When using this controller in combination with the WJ-FS616C, cover the panel of the controller with the panel templates
provided.
SYSTEM CONTROLLER WV-CU550C
123
456
789
MON CAM
UNIT/ESC0
RESETEL-
ZOOMMULTISCREEN
SELECT
FUNCTIONPRE-
POSI STILL
HOME/–  AUTO/+CLOSE...

67
yJoystick Controller
The joystick is used to manually operate the Pan/Tilt
Head, move the cursor position in the setup menu of
the video multiplexer, or to select an area for Electronic
Zooming.
UP:Upward
DOWN:Downward
LEFT:Left
RIGHT:Right
uIris Buttons (IRIS, CLOSE/OPEN)
Close or open the lens iris of cameras equipped with
the specified lens.
When these buttons are pressed at the same time, the
lens iris is reset to the factory default settings.
iFocus button (FOCUS, NEAR/FAR)
Adjusts the lens focus...

68
!6Function button (FUNCTION)
This button is used to display the camera images with a
VCR playback image on the multiscreen monitor.
While displaying the setup menu on the monitor, press-
ing this button will select the next page of the setup
menu.
!7Auto/Increment button (AUTO/+ )
This button is used to activate the auto panning function
if the camera is equipped with the specific future.
While displaying the setup menu on the monitor, press-
ing this button will select the parameter forwardly in the...

69
Installations
The installations described below should be made by
qualified service personnel or system installers.
Modifying the Front Panel
Peel the tape off the supplied panel templates, then attach
them on the front panel of the system controller.
Connection with the WV-CU550C System
Controller
If the supplied 6-conductor cable assembly is used, simply
plug one end of the cable into the DATA IN port of the
video multiplexer and the other end into the DATA OUT port
on the system controller.
If...

70
During setup of the WJ-FS616C with the WV-CU550C system controller, the following buttons and keys of the system controller
correspond with those of the WJ-FS616C as shown below.
SETUP MENU OPERATIONS (WITH WV-CU550C)
FUNCTION LEFT
RIGHT UP
DOWN
HOME/SET
SET  UP/ESC
LEFT
RIGHT UP
DOWNHOME/SET
SET  UP/ESC
EL-ZOOMSTILL
MO NCAM
UNIT/ESC
FUNCTION
HOME/–  AUTO/+ LEFT RIGHTUP
DOWN
AUX1AUX2
SET
SET UP
4
8
12
16
3
7
11
15
2
6
10
14
1
5
9
13
CAMERA/PRESET   POSITION
123
456
789
MON CAM
UNIT/ESC0
SET
Display...

71
When operating the video multiplexer with the WV-CU550C
system controller, the following buttons and keys of the sys-
tem controller correspond with those of the video multiplex-
er.
While the indicator of the [ALT] button is on, control of
the VCR with the buttons shown below is enabled.
: Rewind FUNCTION
: Pause PRE-POSI
: Fast Forward STILL
: Reverse Play CAMERA SET ON A
: Stop EL-ZOOM
: Play CAMERA SET OFF B
: T/L modeC
: T/L mode SET UP D
: Record MULTISCREEN SELECT
Refer to the supplied panel...