Panasonic Video Multiplexer Wj Fs616c Operating Instructions

41
Cable Compensation/VD2/Data
This item lets you select the optimum setting for the cable-
loss compensator and whether to supply the VD2 (sync)
signal or control data to the camera.
Note:These settings will work only for the input channels
that have the multiplex feature with the Data Multiplex
Board WV-BP6164 installed.  The boards are installed
for input channels 1 through 4 at the factory. You can
install boards for other channels. For installations, see
page 12.
1. Press the [FUNCTION] button...

42
4. Select the preset position number to be assigned in the
PRE column by pressing the -or +button.
5. Repeat steps 2 to 4 above to assign other terminal
numbers.
Note:The same channel number can be assigned to
multiple alarm terminals.
In this case, different preset positions can be
assigned, but when alarm occurs at these positions,
the camera movHes to the preset position where
the most recent alarm occurred.
6. Press the [SET UP/ESC] button to execute the settings
and returns to the previous SYSTEM...

43
5. Select the desired waiting time for WAIT TIME by press-
ing the -or +button.
This item lets you set the waiting time to retry if there is
no response from the connected device.
OFF:Selects no retry.
100 – 1000:Selects a waiting time in milli-seconds.
6. Select a number of data bit, 7 or 8, for DATA BIT by
pressing the -or +button.
7. Select the parity check mode for PARITY by pressing
the -or +button.
NONE:No parity check
EVEN:Even parity
ODD:Odd parity
8. Select a number of stop bit, 1 or 2, for...

44
Password
This item lets you select whether to permit free or limited
access to the setup menus.
When PASSWORD is set to ON, the operator must enter the
password to access the setup menus.
1. Move the cursor to the PASSWORD parameter in the
SYSTEM SETUP menu.
2. Select either ON or OFF by pressing the Aor Bbutton.
ON:Enables limited access to the menus.
OFF:Enables freely access to the menus.
The factory default setting is OFF.
Password Registration
Enter a 4-digit password consisting of numbers from...

45
OTHER SETUP MENUS
Camera Download
This item lets you save the camera setup data into the
memory of the video multiplexer.
If the setup contents of the camera should be lost due to
malfunctioning or replacement of a camera, you can simply
reload the data stored in the video multiplexer.
1. Move the cursor to the CAM DOWNLOAD parameter in
the SETUP MENU.
2. Select YES by pressing the Aor Bbutton, then press
the [HOME/SET] button.
The CAM DOWNLOAD table shown in the figure
appears on the monitor...

46
All Reset
This item lets you restore the factory settings without having
to go through each individual menu.
1. Move the cursor to ALL RESET SELECT in the SETUP
MENU, then press the [HOME/SET] button.
The ALL RESET SELECT menu shown in the figure
appears on the monitor screen.
2. Select “YES” by pressing the Aor Bbutton.
3. Press the [HOME/SET] button to execute the all reset
function.
4. First “NOW RESETTING” appears, then “RESET COM-
PLETED”.
5. Press the [SET UP/ESC] button to return to the SETUP...

47
OPERATING PROCEDURES 

48
CONTROLLING THE VIDEO INPUT AND MONITORS
Before starting the following procedures, all system
components should be turned on.
Then set the LOCK switch to the OFF position.
Controlling the Spot Monitor
The operations described below are available on the spot
monitor.
Selecting the Spot Monitor
1. Select the spot monitor by pressing the [SPOT] button.
The indicator (green) in the button is on to indicate the
spot monitor is selected.
2. In this condition, select the images to be displayed on
the...

49
Controlling the Multiscreen
Monitor
The operations described below are available on the multi-
screen monitor.
Note:We recommend using the spot monitor in single spot
for preventing image disturbance when displaying non-
interlace images.
Selecting the Multiscreen Monitor
1. Select the multiscreen monitor by pressing the [MULTI-
SCREEN] button repeatedly.
The indicator in the button is on to indicate the multi-
screen monitor is selected.
Note:The indicator in the button blinks to indicate the...

50
3. To cancel this mode, press the [STILL] button to return
to the image previously shown.
The indicator in the button goes off.
Zooming Single Spot (Live)
While the image on the monitor screen is displayed in sin-
gle spot mode, the image can be zoomed followed the pro-
cedure below.
1. Select an image to be zoomed on the monitor by press-
ing a [1 – 16] button.
The indicator in the selected button lights and the cam-
era image corresponding to the button appears on the
monitor screen.
2. Press the...