Panasonic Video Multiplexer Wj Fs616c Operating Instructions

31
Camera Title Display
This item lets you enable or disable display of the camera
title on the spot monitor.
1. Move the cursor to the TITLE DISPLAY parameter.
2. Select either ON or OFF.
ON:Enables display of the camera title on the monitor
screen.
OFF:Disables display of the camera title on the monitor
screen.
The factory default setting is ON.
Clock Display
This item lets you enable or disable the clock display on the
spot monitor.
1. Move the cursor to the CLOCK DISPLAY parameter.
2. Select either...

32
RECORD OR MULTISCREEN 2 OUTPUT SETUP
The procedure described below let you determine the
mode for the REC OUT connector on the rear of the video
multiplexer.
As described before, this output can be used for recording
images on the time lapse VCR or monitoring images as
multiscreen 2 monitor.
1. Move the cursor to the REC/MULTI2 parameter in the
SETUP MENU by pressing the Cor Dbutton.
2. Select either REC OUTPUT or MULTI2 OUTPUT by
pressing the Aor Bbutton.
REC OUTPUT:Enables recording images on the...

33
Dynamic Recording
This item lets you select the cameras for dynamic recording
mode in non-alarm condition.
If five or more cameras are connected to the video multi-
plexer, the channels selected for dynamic recording are
recorded with priority.
1. Move the cursor to DYNAMIC REC SETUP by pressing
the Cor Dbutton and then press the [HOME/SET] but-
ton.
The DYNAMIC REC SETUP menu as shown in the figure
appears on the monitor screen.
2. Move the cursor to the PRIORITY column to be record-
ed with dynamic...

34
Multiscreen 2 Output Setup
These items let you select the display mode when connect-
ing the Record Output (REC OUT) to the monitor for multi-
screen 2 monitor.
1. Move the cursor to the REC/MULTI2 parameter in the
SETUP MENU.
2. Select MULTI2 OUTPUT and then press the
[HOME/SET] button.
The MULTI2 OUTPUT SETUP menu as shown in the fig-
ure appears on the monitor screen. 3. Select the desired switching timing indicated as the
field interval (4 to 999) by pressing the Aor Bbutton.
Notes: 
• Numbers...

35
Camera Display Position
This item lets you select the position where the camera
images will be displayed on the multiscreen 2 monitor.
1. Move the cursor to DISPLAY POSITION, then press the
[HOME/SET] button.
The table shown in the figure appears on the monitor.
2. Move the cursor to the desired channel number by
pressing the Cor Dbutton.
3. Select the numbers of the cameras to be displayed by
pressing the Aor Bbutton.
The images of the selected cameras are displayed one
after another on the monitor...

36
SYSTEM SETUP
The procedure described below let you determine the sys-
tem designation and display the system status. 
1. Move the cursor to SYSTEM SETUP in the SETUP
MENU and then press the [HOME/SET button.
The SYSTEM SETUP menu as shown in the figure
appears on the monitor screen.
2. Press the [FUNCTION] button to display the next page
of the menu. Press this button again to return to the pre-
vious page of the menu.Clock Setup
This item lets you set the current time and date.
1. Move the cursor to...

37
Camera Title Setup
This item lets you edit the camera title to be displayed on
the monitor screen.
Up to 8 alphanumeric characters can be displayed on the
monitor.
1. Move the cursor to TITLE SETUP in the SYSTEM SETUP
menu by pressing the Cor Dbutton, then press the
[HOME/SET] button.
The TITLE SETUP menu shown in the figure appears on
the monitor screen.
2. Move the cursor to the channel you want to edit by
pressing the Cor Dbutton, then press the
[HOME/SET] button.
The cursor moves to the right...

38
2. Select SEQ1 and then press the [HOME/SET] button.
The SEQ1 SETUP menu shown in the figure appears on
the monitor screen.
Auto Skip
1. Move the cursor to the AUTO SKIP parameter.
2. Select either ON or OFF.
ON:Enables the auto skip function.
OFF:Disables the auto skip function.
The factory default setting is OFF.
Note:The auto skip function is not available when play-
ing back videotape images.
Image Assignment
1. Move the cursor to the CAM column you want to edit for
the step number by pressing the...

39
4. After finishing the settings, press the [SET UP/ESC] but-
ton to execute the settings and return to the previous
SYSTEM SETUP menu.
Multi Sequence (SEQ2, SEQ3)
This item lets you program or edit a Multi Sequence.
Up to 5 steps can be assigned in the table shown below.
You can also enable the auto skip function to skip any
steps where no video signal is present.
The duration of each step is determined by the dwell time
setting.
According to the factory default setting, SEQ2 is displayed
on four...

40
Preset Position
1. Move the cursor to the PRE column you want to edit for
the area number by pressing the C, D, Aor Bbutton.
2. Select the desired preset position number for the cam-
era in the PRE column by pressing the -or +button.
3. Repeat steps 1 and 2 above to assign other area num-
bers.
Notes:
• When the STEP parameter in this table is on PLAY,
it is not possible to select a preset position in the
PRE column.
• It is possible to assign the same camera channel to
multiple area numbers within a...