Panasonic Video Multiplexer Wj Fs616c Operating Instructions

							31
Camera Title Display
This item lets you enable or disable display of the camera
title on the spot monitor.
1. Move the cursor to the TITLE DISPLAY parameter.
2. Select either ON or OFF.
ON:Enables display of the camera title on the monitor
screen.
OFF:Disables display of the camera title on the monitor
screen.
The factory default setting is ON.
Clock Display
This item lets you enable or disable the clock display on the
spot monitor.
1. Move the cursor to the CLOCK DISPLAY parameter.
2. Select either ON or OFF.
ON:Enables clock display on the monitor screen.
OFF:Disables clock display on the monitor screen.
The factory default setting is ON.
3. After finishing the setting, press the [SET UP/ESC] but-
ton to return to the previous SETUP MENU.
SPOT OUTPUT SETUP
The procedure described below let you determine the dis-
play mode of the spot monitor.
Move the cursor to SPOT OUTPUT SETUP in the SETUP
MENU, and then press the [HOME/SET] button.
The SPOT OUTPUT SETUP menu appears on the moni-
tor screen as shown in the figure.
       WJ-FS616C SETUP MENU
       ALARM SETUP *
       MULTI OUTPUT SETUP *
       SPOT OUTPUT SETUP *    
       REC/MULTI2     REC OUTPUT *
       SYSTEM SETUP *
       CAM DOWNLOAD   NO
       CAM UPLOAD     NO
       ALL RESET SELECT *
           SPOT OUTPUT SETUP
        TITLE DISPLAY  ON
        CLOCK DISPLAY  ON 
						

							32
RECORD OR MULTISCREEN 2 OUTPUT SETUP
The procedure described below let you determine the
mode for the REC OUT connector on the rear of the video
multiplexer.
As described before, this output can be used for recording
images on the time lapse VCR or monitoring images as
multiscreen 2 monitor.
1. Move the cursor to the REC/MULTI2 parameter in the
SETUP MENU by pressing the Cor Dbutton.
2. Select either REC OUTPUT or MULTI2 OUTPUT by
pressing the Aor Bbutton.
REC OUTPUT:Enables recording images on the time
lapse VCR.
MULTI2 OUTPUT:Enables monitoring images on the
connected multiscreen 2 monitor.
The factory default setting is REC OUTPUT.
3. Press the [HOME/SET] button to execute the selection
and then the selected submenu will appear on the mon-
itor screen.Record Output Setup
Select REC OUTPUT in the menu and then press the
[HOME/SET] button.
The REC OUTPUT SETUP menu as shown in the figure
appears on the monitor screen.
These items let you determine the mode for recording on
the time lapse VCR.
Camera Title Display
This item lets you enable or disable recording of the cam-
era title on the VCR.
1. Move the cursor to the TITLE DISPLAY parameter.
2. Select either ON or OFF.
ON:Enables recording of the camera title on the VCR.
OFF:Disables recording of the camera title on the VCR.
The factory default setting is ON.
Clock Display
This item lets you enable or disable recording of the clock
display on the VCR.
1. Move the cursor to the CLOCK DISPLAY parameter.
2. Select either ON or OFF. 
ON:Enables recording of clock display on the VCR.
OFF:Disables recording of clock display on the VCR.
The factory default setting is ON.
       WJ-FS616C SETUP MENU
       ALARM SETUP *
       MULTI OUTPUT SETUP *
       SPOT OUTPUT SETUP *    
       REC/MULTI2     REC OUTPUT *
       SYSTEM SETUP *
       CAM DOWNLOAD   NO
       CAM UPLOAD     NO
       ALL RESET SELECT *
            REC OUTPUT SETUP
        TITLE DISPLAY  ON
        CLOCK DISPLAY  ON
        DYNAMIC REC SETUP *
        REC MODE SETUP * 
						

							33
Dynamic Recording
This item lets you select the cameras for dynamic recording
mode in non-alarm condition.
If five or more cameras are connected to the video multi-
plexer, the channels selected for dynamic recording are
recorded with priority.
1. Move the cursor to DYNAMIC REC SETUP by pressing
the Cor Dbutton and then press the [HOME/SET] but-
ton.
The DYNAMIC REC SETUP menu as shown in the figure
appears on the monitor screen.
2. Move the cursor to the PRIORITY column to be record-
ed with dynamic recording for the camera number by
pressing the C, D, A, or Bbuttons.
3. Select either ON or OFF by pressing the -or +but-
ton.
OFF:Disables recording images with priority.
ON:Enables recording images preferentially over other
input images.
The factory default settings are OFF.
4. Repeat steps 2 and 3 above to set other cameras.
Note:It is recommended to select up to 2 cameras.
5. When satisfied with all of the above steps, press the
[SET UP/ESC] button to execute the selection and
return to the previous REC OUTPUT SETUP menu.
Note:Recording is not enabled in dynamic recording
mode when EXT4 is selected for MODE 9 in the
REC MODE SETUP menu.
Recording Mode Setup
This item lets you select a recording mode on the time
lapse VCR.
1. Move the cursor to REC MODE SETUP by pressing the
Cor Dbutton and then press the [HOME/SET] button.
The REC MODE SETUP menu as shown in the figure
appears on the monitor screen.
2. Move the cursor to the MODE parameter in the menu by
pressing the Cor Dbutton.
3. Select a mode number by pressing the - or +button.
MODE 0:Normal recording mode
MODE 1 - 8:Time Lapse Mode (VCR without camera
switching pulse)
MODE 9:Time Lapse Mode (VCR with camera switch-
ing pulse)
The factory default setting is “0”.
Note:To select MODE 1 - 8, you must first complete the
settings described below.
Recording Mode Setting Details
You can assign the camera switching timing to any one of
MODE1 to MODE8 when using the VCR without camera
switching pulse.
1. Move the cursor to the desired MODE number to be
assigned by pressing the Cor Dbutton.
2. Press the [HOME/SET] button to move the cursor to the
right in the switching timing column.
Note:The cursor does not move to this column
when MODE 0 is selected in this table.
The value is fixed to 1 in this column.
           DYNAMIC REC SETUP 
 
       CAM PRIORITY    CAM PRIORITY 
       1CH   OFF       9CH   OFF
       2CH   OFF      10CH   OFF 
       3CH   OFF      11CH   OFF 
       4CH   OFF      12CH   OFF 
       5CH   OFF      13CH   OFF 
       6CH   OFF      14CH   OFF 
       7CH   OFF      15CH   OFF  
       8CH   OFF      16CH   OFF 
     
             REC MODE SETUP 
 
    MODE 0             0123456789 
                       ABCDEFGHIJK 
    MODE0    1  REAL   LMNOPQRSTUV 
    MODE1  ---  ----   WXYZ 
    MODE2  ---  ----   abcdefghijk
    MODE3  ---  ----   lmnopqrstuv 
    MODE4  ---  ----   wxyz  
    MODE5  ---  ----   
¤=?#&()*
    MODE6  ---  ----   +,-./:;E 
    MODE7  ---  ----    
    MODE8  ---  ----  
    MODE9 EXT1  -EXT   
   
Current REC MODE
REC MODE Title
REC MODE Parameter 
						

							34
Multiscreen 2 Output Setup
These items let you select the display mode when connect-
ing the Record Output (REC OUT) to the monitor for multi-
screen 2 monitor.
1. Move the cursor to the REC/MULTI2 parameter in the
SETUP MENU.
2. Select MULTI2 OUTPUT and then press the
[HOME/SET] button.
The MULTI2 OUTPUT SETUP menu as shown in the fig-
ure appears on the monitor screen. 3. Select the desired switching timing indicated as the
field interval (4 to 999) by pressing the Aor Bbutton.
Notes: 
• Numbers can also be input directly with the Camera
Number buttons (1 - 10).
• Refer to the operating instructions of the VCR for
switching timing.
When MODE9 is selected in this table, select EXT1
or EXT4 by pressing the Aor Bbutton.
EXT1:Enables spot image recording on the VCR.
EXT4:Enables quad images recording on the VCR.
4. Press the [HOME/SET] button to move the cursor to the
right in the recording mode title column.
The square cursor appears in the character table.
5. To select a character, move the cursor on the desired
character in the table by pressing the C, D, A, or B
buttons.
6. Press the [HOME/SET] button to pick up the character
and place it in the title column.
7. Repeat steps 5 and 6 above to edit the title.
8. If a wrong character is selected, press the - or +
button to move the cursor in the title column.
Note:Press the + button to move the cursor to the right,
or press the - button to move the cursor to the left.
Then press the [HOME/SET] button to overwrite the
character with the character selected from the table.
9. Press the [SET UP/ESC] button. The cursor moves to
MODE number.
10. Repeat steps 1 to 9 above to assign the other MODE
numbers.
11. After completing the setting, press the [SET UP/ESC]
button to return to the REC OUTPUT SETUP menu.
12. After finishing the setting, press the [SET UP/ESC] but-
ton to return to the previous SETUP MENU.
       WJ-FS616C SETUP MENU
       ALARM SETUP *
       MULTI OUTPUT SETUP *
       SPOT OUTPUT SETUP *    
       REC/MULTI2     MULTI2 OUTPUT *
       SYSTEM SETUP *
       CAM DOWNLOAD   NO
       CAM UPLOAD     NO
       ALL RESET SELECT *
          MULTI2 OUTPUT SETUP
        DISPLAY POSITION *
        SEQUENCE MODE  SEQ2 
						

							35
Camera Display Position
This item lets you select the position where the camera
images will be displayed on the multiscreen 2 monitor.
1. Move the cursor to DISPLAY POSITION, then press the
[HOME/SET] button.
The table shown in the figure appears on the monitor.
2. Move the cursor to the desired channel number by
pressing the Cor Dbutton.
3. Select the numbers of the cameras to be displayed by
pressing the Aor Bbutton.
The images of the selected cameras are displayed one
after another on the monitor screen.
Note:Numbers can also be input directly with the
Camera Number buttons (1 - 10).
4. After completing the setting, press the [SET UP/ESC]
button to return to the previous MULTI 2 OUTPUT
SETUP menu.
Note:This operation only affects the camera display
positions.
It has no effect on the camera channel, recording
order or sequence order.
Sequence Mode
This item lets you select the sequence pattern for display
on the multiscreen 2 monitor.
Refer to Sequence Setup on page 37 for more details.
1. Move the cursor to the SEQUENCE MODE parameter.
2. Select the desired sequence mode.
SEQ1:Spot Sequence
SEQ2:Multi Sequence
SEQ3:Multi Sequence
The factory default setting is SEQ2.
3. After finishing the setting, press the [SET UP/ESC] but-
ton to return to the previous SETUP MENU.
  1         2         3         4
   
  
  
  5         6         7         8
  
  
  
  9         10        11        12
  
  
  
  13        14        15        16 
						

							36
SYSTEM SETUP
The procedure described below let you determine the sys-
tem designation and display the system status. 
1. Move the cursor to SYSTEM SETUP in the SETUP
MENU and then press the [HOME/SET button.
The SYSTEM SETUP menu as shown in the figure
appears on the monitor screen.
2. Press the [FUNCTION] button to display the next page
of the menu. Press this button again to return to the pre-
vious page of the menu.Clock Setup
This item lets you set the current time and date.
1. Move the cursor to CLOCK SETUP in the SYSTEM
SETUP menu and then press the [HOME/SET] button.
The cursor moves to the right editing area.
2. Select the month by pressing the Aor Bbutton.
3. Move the cursor to the right by pressing the Cor D
button, then select the date by pressing the Aor B
button.
4. Select the last 2 digits for the year and time (military
time) as similarly by pressing the Cor Dbutton and
the Aor Bbutton.
5. After completing the setting, press the [SET UP/ESC]
button to move the cursor to CLOCK SETUP.
The selected time and date are updated when the [SET
UP/ESC] button is pressed.
Clock Display Position
This item lets you select the position where the clock will be
displayed on the monitor screen.
1. Move the cursor to CLOCK POSITION in the SYSTEM
SETUP menu and then press the [HOME/SET] button.
The position setting menu shown in the figure appears
on the monitor screen.
2. Move the clock position by pressing the C, D, Aor B
button.
Note:In the multiscreen display with the multiscreen
output or record output, the clock display is shifted
one line from the preset position if the camera title
and the clock are preset to the same position.
3. Press the [SET UP/ESC] button to execute the selection
and return to the previous SYSTEM SETUP menu.
       WJ-FS616C SETUP MENU
       ALARM SETUP *
       MULTI OUTPUT SETUP *
       SPOT OUTPUT SETUP *    
       REC/MULTI2     REC OUTPUT *
       SYSTEM SETUP *
       CAM DOWNLOAD   NO
       CAM UPLOAD     NO
       ALL RESET SELECT *
              SYSTEM SETUP      1 OF 2
        CLOCK SETUP    JAN 1.97  0:00
        CLOCK POSITION *
        TITLE SETUP *
        TITLE POSITION *
        SEQUENCE SETUP SEQ1 *
        SEQ TIMING-MLT INT(TIME-ADJ)
        SEQ TIMING-SPT INT
        LOCK MODE      ALL
              SYSTEM SETUP      2 OF 2
        CABLE COMP/VD2/DATA SETUP *
        ALM TERMINAL SETUP *
        PLAYBACK MODE  FIELD
        DATA MODE      CU
        RS-232C MODE   VCR
        COM PORT SETUP *      
        VCR IN SELECT  VIDEO
        DAISY MODE     OFF
        UNIT ADDR.SET  1
        PASSWORD       OFF
        DEC11.96 12:00:00 
  
                
                 
 
 
 
 
              CAMTITLE
 
 
 
  
  
    
						

							37
Camera Title Setup
This item lets you edit the camera title to be displayed on
the monitor screen.
Up to 8 alphanumeric characters can be displayed on the
monitor.
1. Move the cursor to TITLE SETUP in the SYSTEM SETUP
menu by pressing the Cor Dbutton, then press the
[HOME/SET] button.
The TITLE SETUP menu shown in the figure appears on
the monitor screen.
2. Move the cursor to the channel you want to edit by
pressing the Cor Dbutton, then press the
[HOME/SET] button.
The cursor moves to the right editing column, and the
square cursor appears on the character table.
3. To select a character, move the cursor on the desired
character in the table by pressing the C, D, Aor B
button.
4. Then press the [HOME/SET] button to pick up the char-
acter, and place it in the editing column.
5. Repeat steps 3 and 4 above until the title for a certain
camera is completed.
6. If a wrong character is selected, press the -or +but-
ton to move the cursor in the editing column.
Note:Press the +button to move the cursor to the
right, or press the -button to move the cursor to
the left.
Then press the [HOME/SET] button to overwrite
the character with the character selected in the table.
7. Press the [SET UP/ESC] button to move the cursor to
the channel number column.8. Press the [FUNCTION] button to display the next page,
then press this button again to return to the previous
page.
9. Repeat steps 2 to 7 above to edit the titles for the rest of
the cameras.
10. After completing the setting, press the [SET UP/ESC]
button to return to the previous SYSTEM SETUP menu.
Camera Title Display Position
This item lets you select the camera title position to be dis-
played on the monitor screen.
Refer to the Clock Display Position Setting on page 36 for
more details.
1. Move the cursor to TITLE POSITION in the SYSTEM
SETUP menu, then press the [HOME/SET] button.
The position setting menu appears on the monitor
screen.
2. Move the title by pressing the C, D, Aor Bbutton.
Note:In the Multiscreen display with the multiscreen
output or record output, the clock display is shifted
one line from the preset position if the camera title
and the clock are preset to the same position.
3. Press the [SET UP/ESC] button to execute the selection
and return to the previous SYSTEM SETUP menu.
Sequence Setup
This item lets you program the sequence pattern for spot or
multi sequence.
You can either program a spot sequence (SEQ1) or two
multi sequences (SEQ2, SEQ3).
Spot Sequence (SEQ1)
This item lets you program or edit a spot sequence.
Up to 32 steps can be assigned in the table shown in the
figure.
You can also enable the auto skip function to skip any
steps where no video signal is present.
The duration of each step is determined by the dwell time
setting.
The factory default setting is sequential display of 16 cam-
era images.
1. Move the cursor to the SEQUENCE SETUP parameter in
the SYSTEM SETUP menu.
              TITLE SETUP       1 OF 2 
 
     1CH 1-------      0123456789 
     2CH 2-------      ABCDEFGHIJK 
     3CH 3-------      LMNOPQRSTUV 
     4CH 4-------      WXYZ 
     5CH 5-------      abcdefghijk
     6CH 6-------      imnopqrstuv 
     7CH 7-------      wxyz 
     8CH 8-------      
¤=?#&()*
                       +,-./:;E 
       
     
                     
@
              TITLE SETUP       2 OF 2 
 
     9CH 9-------      0123456789 
    10CH 10------      ABCDEFGHIJK 
    11CH 11------      LMNOPQRSTUV 
    12CH 12------      WXYZ 
    13CH 13------      abcdefghijk
    14CH 14------      imnopqrstuv 
    15CH 15------      wxyz 
    16CH 16------      
¤=?#&()*
                       +,-./:;E 
       
     
                     
@ 
						

							38
2. Select SEQ1 and then press the [HOME/SET] button.
The SEQ1 SETUP menu shown in the figure appears on
the monitor screen.
Auto Skip
1. Move the cursor to the AUTO SKIP parameter.
2. Select either ON or OFF.
ON:Enables the auto skip function.
OFF:Disables the auto skip function.
The factory default setting is OFF.
Note:The auto skip function is not available when play-
ing back videotape images.
Image Assignment
1. Move the cursor to the CAM column you want to edit for
the step number by pressing the C, D, Aor Bbutton.
2. Select the desired camera or playback channel in the
CAM column by pressing the -or +button.
1 - 16:Camera Channel
P1 - P16:Playback Channel
–:Not Assigned
Notes:
• Pressing the Camera Number button assigns the
camera channel directly.
• Any playback steps programmed in a sequence are
excluded from display on the spot monitor and mul-
tiscreen 2 monitor due to the way the system is
designed.
3. Repeat steps 1 and 2 above to assign other steps.
Preset Position
1. Move the cursor to the PRE column you want to edit for
the step number by pressing the C, D, Aor Bbutton.2. Select the desired preset position number for the cam-
era in the PRE column by pressing the -or +button.
Note:A preset position assigned to a step that has
been assigned to a playback channel is invalid.
3. Repeat steps 1 and 2 above to assign other steps.
Dwell Time
• Uniform Dwell Time
1. Move the cursor to the DWELL TIME parameter by
pressing the Cor Dbutton.
2. Select the desired dwell time by pressing the Aor
Bbutton.
Dwell Time can be selected between 0SEC and
30SEC.
Note:If 0SEC is selected for the dwell time, the
spot sequence is not activated.
• Individual Dwell Time
1. Move the cursor to the TIME column you want to
edit for the step number by pressing the C, D, A
or Bbutton.
2. Select the desired dwell by pressing the -or +
button.
Steps for which a different dwell time has been
selected are marked “–” in the DWELL TIME para-
meter. Previous settings made in the DWELL TIME
parameter become invalid.
Programming Steps 17 to 32
1. Press the [FUNCTION] button to display the next page
of the table.
The table shown in the figure appears on the monitor
screen.
2. Program the sequence pattern for steps 17 to 32 as
described previously.
3. Press the [FUNCTION] button to display the previous
page of the table.
       SEQ1(SPOT-SEQUENCE)SETUP 2 OF 2
            
  STEP CAM PRE TIME  STEP CAM PRE TIME
   17   -   -  2SEC   25   -   -  2SEC
   18   -   -  2SEC   26   -   -  2SEC
   19   -   -  2SEC   27   -   -  2SEC
   20   -   -  2SEC   28   -   -  2SEC
   21   -   -  2SEC   29   -   -  2SEC
   22   -   -  2SEC   30   -   -  2SEC
   23   -   -  2SEC   31   -   -  2SEC
   24   -   -  2SEC   32   -   -  2SEC
 
       SEQ1(SPOT-SEQUENCE)SETUP 1 OF 2
     AUTO SKIP  OFF
     DWELL TIME 2SEC
 STEP CAM PRE TIME   STEP CAM PRE TIME
   1  1CH  -  2SEC     9  9CH  -  2SEC
   2  2CH  -  2SEC    10 10CH  -  2SEC
   3  3CH  -  2SEC    11 11CH  -  2SEC
   4  4CH  -  2SEC    12 12CH  -  2SEC
   5  5CH  -  2SEC    13 13CH  -  2SEC
   6  6CH  -  2SEC    14 14CH  -  2SEC
   7  7CH  -  2SEC    15 15CH  -  2SEC
   8  8CH  -  2SEC    16 16CH  -  2SEC
 
    
						

							39
4. After finishing the settings, press the [SET UP/ESC] but-
ton to execute the settings and return to the previous
SYSTEM SETUP menu.
Multi Sequence (SEQ2, SEQ3)
This item lets you program or edit a Multi Sequence.
Up to 5 steps can be assigned in the table shown below.
You can also enable the auto skip function to skip any
steps where no video signal is present.
The duration of each step is determined by the dwell time
setting.
According to the factory default setting, SEQ2 is displayed
on four screen segments (quad) and SEQ3 on nine seg-
ments.
1. Move the cursor to the SEQUENCE SETUP parameter in
the SYSTEM SETUP menu.
2. Select SEQ2 or SEQ3 and then press the [HOME/SET]
button.
The corresponding SETUP table shown in the figure
appears on the monitor screen.
Auto Skip
1. Move the cursor to the AUTO SKIP parameter by press-
ing the Cor Dbutton.
2. Select either ON or OFF by pressing the Aor Bbutton.
ON:Enables the auto skip function.
OFF:Disables the auto skip function.
The factory default setting is OFF.
Note:The auto skip function is not available when play-
ing back videotape images.Camera/Playback
This item lets you select the camera or playback image
to be displayed at each step.
1. Move the cursor to the STEP parameter by pressing
the Cor Dbutton.
2. Select either CAM or PLAY by pressing the Aor B
button.
CAN:Enables display of camera image.
PLAY:Enables display of playback image.
The factory default setting is CAM.
Dwell Time
1. Move the cursor to the DWELL TIME parameter by
pressing the Cor Dbutton.
2. Select the desired dwell time by pressing the Aor B
button.
Dwell Time can be selected between 0SEC and 30SEC.
Note:If 0SEC is selected for the dwell time, the step will
not be displayed on the multiscreen monitor.
Image Assignment
1. Move the cursor to the CAM column you want to edit for
the area number by pressing the C, D, Aor Bbutton.
2. Select the desired camera or playback channel in the
CAM column by pressing the -or +button.
1 - 16:Camera Channel
P1 - P16:Playback Channel
–:Not Assigned
3. Repeat steps 1 and 2 above to assign other area num-
bers.
Note:
The multiscreen pattern of each step is determined
automatically as follows:
• For example, if several camera channels are
assigned to area numbers, the screen segmen-
tation that will accommodate the highest area
number will be selected.
• Areas not assigned a camera channel, or
assigned a channel to which no camera is con-
nected, are displayed in blackout.
• Pressing the Camera Number button assigns
the camera channel directly.
      SEQ3(MULTI-SEQUENCE)SETUP 1 OF 5
      AUTO SKIP  OFF
      STEP 1     CAM
      DWELL TIME 5SEC
        
      AREA  CAM PRE  AREA  CAM PRE    
        1   1CH  -     9    -   -   
        2   2CH  -    10    -   -   
        3   3CH  -    11    -   -   
        4   4CH  -    12    -   -   
        5   5CH  -    13    -   -   
        6   6CH  -    14    -   -   
        7   7CH  -    15    -   -    
        8   8CH  -    16    -   -   
 
   
      SEQ2(MULTI-SEQUENCE)SETUP 1 OF 5
      AUTO SKIP  OFF
      STEP 1     CAM
      DWELL TIME 3SEC
        
      AREA  CAM PRE  AREA  CAM PRE    
        1   1CH  -     9    -   -   
        2   2CH  -    10    -   -   
        3   3CH  -    11    -   -   
        4   4CH  -    12    -   -   
        5    -   -    13    -   -   
        6    -   -    14    -   -   
        7    -   -    15    -   -    
        8    -   -    16    -   -   
 
    
						

							40
Preset Position
1. Move the cursor to the PRE column you want to edit for
the area number by pressing the C, D, Aor Bbutton.
2. Select the desired preset position number for the cam-
era in the PRE column by pressing the -or +button.
3. Repeat steps 1 and 2 above to assign other area num-
bers.
Notes:
• When the STEP parameter in this table is on PLAY,
it is not possible to select a preset position in the
PRE column.
• It is possible to assign the same camera channel to
multiple area numbers within a step.
In this case, make sure to assign the same preset
positions in the table.
Programming Steps 2 to 5
1. Press the [FUNCTION] button to display the next page
of the table.
2. Program the sequence pattern for steps 2 to 5 accord-
ing to the procedure described above.
3. After finishing the settings, press the [SET UP/ESC] but-
ton to execute the settings and returns to the previous
SYSTEM SETUP menu.
Sequence Timing (Multiscreen
Monitor)
This item lets you select between internal and external con-
trol for advancing the sequence on the multiscreen monitor.
It also lets you select functions of devices connected to pin
26 of the ALARM/REMOTE port.
One of these functions is input of the time adjustment signal
from a VCR, the other enables external sequence advance
for multiscreen monitor.
1. Move the cursor to the SEQ TIMING-MLT parameter in
the SYSTEM SETUP menu.
2. Select INT (TIME-ADJ) or EXT.
INT:Advances a sequence by the dwell time that was
programmed in the SEQUENCE SETUP menu.
It enables input of the time adjustment signal from a
Time Lapse VCR.
EXT:Enables external sequence advance.
The factory default setting is INT (TIME-ADJ).Notes:
• If EXT is selected, time adjustment input from a
Time Lapse VCR is disabled.
• If EXT is selected, connect the external sequence
switch to pin 26 of the ALARM/REMOTE port.
• The multiplexer accepts the time adjustment signal
for 6 minutes, that is, 3 minutes before and 3 min-
utes after the exact time (For example, from 9:57:00
through 10:03:00.  Time is adjusted to 10:00:00).
Sequence Timing (Spot Monitor)
This item lets you select between internal and external con-
trol for advancing the sequence on the spot monitor.
1. Move the cursor to the SEQ TIMING-SPT parameter in
the SYSTEM SETUP menu.
2. Select either INT or EXT.
INT:Advances a sequence by the dwell time that was
programmed in the SEQUENCE SETUP menu.
EXT:Advances a sequence by the input from pin 6 of
the ALARM/REMOTE port.
The factory default setting is INT.
Lock Mode
This item lets you determine which buttons will be locked
while the LOCK switch is in ON position.
1. Move the cursor to the LOCK MODE parameter in the
SYSTEM SETUP menu.
2. Select either ALL or VCR.
VCR:Locks the VCR Control Buttons.
ALL:Locks all the buttons.
The factory default setting is ALL.
Note:The LOCK indicator only lights when the LOCK
switch is in ON position and LOCK MODE is set to
ALL.