Panasonic Uf 6000au Operating Instructions Manual

							Troubleshooting
141
Problem Solving
When you do not hear a dial tone through the telephone connected to the machine or when the telephone 
does not ring (No automatic receive).
Checking the Telephone Line
1Unplug the Telephone Line Cable from the 
telephone jack that was supplied by the 
telephone company.
2Plug a different regular telephone into the 
same telephone jack.
3Check for dial tone through the handset.  If 
there is still no dial tone, report it to your local 
telephone company.
or
Call from another telephone to this number.  If 
the telephone does not ring, report it to your 
local telephone company. 
						

							142
Appendix
Specifications
Compatibility ITU-T Group 3
Coding Scheme MH, MR, MMR (Conforms to ITU-T Recommendations)
Modem Type ITU-T V.34, V.17, V.29, V.27ter and V.21 
Modem Speed 33600 - 2400 bps
Document Size Max. : 10.1 x 78.7 in (257 x 2000 mm)
(with operators assistance)
Min. : 5.8 x 5.0 in (148 x 128 mm)
Document Thickness Single page : 0.0024 - 0.0060 in (0.06 - 0.15 mm)
Multiple pages : 0.0024 - 0.0039 in (0.06 - 0.10 mm)
ADF Capacity
(Automatic Document Feeder)Built-in, up to 50 Sheets
Note : The document limitation to send multiple pages is as follows
  Document Size Document Thickness
Up to 20 pages Up to 10.1 × 14.3 in 0.0024 - 0.0048 in 
(257 x 364 mm)
Up to 50 pages A4 or Letter size 0.0024 - 0.0039 in 
* Please note that although the size and thickness meets the specifications, you   
might not be able to set 50 pages with some types of papers.
Scanning Method Sheet Feeding with CCD type image sensor
Effective Scanning Width 8.3 in (212 mm)
Scanner Resolution
HorizontalVe r t ic a l
Standard 203 pels/inch  ¥  98 lines/inch 
(8 pels/mm)  ¥ (3.85 lines/mm)
Fine 203 pels/inch  ¥ 196 lines/inch
(8 pels/mm)  ¥ (7.7 lines/mm)
Super Fine 406 pels/inch  ¥  391 lines/inch
(16 pels/mm)  ¥  (15.4 lines/mm)
(Interpolated)
Recording Method Laser  Printer
Recording Paper Plain  Paper
Recording Paper Size Letter, A4 or Legal
Printer Resolution Fax/Copy Mode : 406 x 391 dpi
Printer Mode  : 600 x 600 dpi
300 x 300 dpi
Effective Recording Size Letter : 8.2 x 10.7 in (208 x 271 mm)
A4 : 8.0 x 11.4 in (202 x 289 mm)
Legal : 8.2 x 13.7 in (208 x 348 mm) 
						

							Specifications
143Appe ndix
NOTE1. The left and right  print  margin is 0.22 in  (5.5 mm) when printing  a Letter or Legal size  document 
with 600 dpi from a PC. Print Margin (See Note 1)
Recording Paper Capacity Approx. 250 sheets (using 20 lbs paper)
One-Touch/Abbreviated Dialing 
Memory Capacity132 stations 
(including 28 One-Touch keys and 4 Program keys)
Each station can register up to 36 digits for each telephone number (including 
pauses and spaces) and up to 15 characters for each station name
Image Memory Capacity 480 pages
(Based on ITU-T Image No.1 using Standard Resolution)
0.16 in
(4 mm)
0.16 in
(4 mm)
0.16 in
(4 mm) 0.16 in
(4 mm) 
						

							Specifications
144
Power Supply 120VAC, 60Hz, Single Phase
Power Consumption Standby (Sleep Mode : On) Less than 1.2 Wh
Standby (Energy-Saver : On) Approx. 6.0 Wh
Standby (Energy-Saver : Off) Approx. 21.0 Wh
[Room temperature : 77°F (25°C)]
Transmission Approx. 17.0 W 
Reception Approx. 460 W
Copy Approx. 470 W
Max Approx. 470 W
Dimensions 14.6 x 18.0 x 9.8 in (W x D x H)
(370 x 457 x 250 mm)
(excluding Projections and optional Paper Cassette)
Weight Approx. 20 lbs (Approx. 9.0 kg)
(excluding consumable supplies and options)
Operating Environment Temperature : 50 to 95°F (10 to 35°C)
Relative Humidity : 15 to 70%
FCC Registration Number US:BTLFA33BMGCS01-01 (US:ACJFA33BUF-6000)
Ringer Equivalence 3.3B 
						

							145Appendix
Recording Paper Specifications
In general, most photocopy papers will also work very well.  There are many name and generic  brands of 
paper available.  We recommend that you test various papers until you obtain the results you are looking for.
The  following table summa rizes the major specifications to consider wh en selecting white or colored pap er.
NOTE1. It is possible that the paper could meet all of the specifications listed above and still not print 
well because of the  variations in paper manufacturing.   Therefore, we  recommend that you  test 
the paper thoroughly before purchasing.
Basic Weight
16 to 24 lb (60 to 90 g/m2)
Cut Edge Conditions Cut with sharp blades, no visible frayed edges
Grain Long grain
Moisture Content 3.7% to 5.3% by weight
Opacity 88% minimum
Packing Polylaminated moisture-proof ream wrap
Sizes Letter : 8.5 x 11 in (216 x 279 mm)
A4 : 8.3 x 11.7 in (210 x 297 mm)
Legal : 8.5 x 14 in (216 x 356 mm)
Type Cut sheet 
						

							146
Options and Supplies
Please contact your local Panasonic dealer for availability.
A. Options:
B. Supplies:
Order No. Illustration Description
UE-403176 Handset Kit
UE-409070250-Sheet Letter / Legal / A4 Size Paper Cassette with the 
Feeder Unit
Order No. Illustra tion Description
DZHT000027 Verification Stamp
UG-5510 Toner Cartridge 
						

							147Appendix
FCC Notice for Users in USA
This equipment has bee n te sted and found to co mply with  the  limits for a Class B digital de vice, pursuant to 
Pa rt 15  of the FCC Rules. These limits a re designed to provide reasonable protection again st harmful 
interferen ce in a residen tial insta lla tion. This equ ipment gene rates, uses and can radiate radio fre quency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 
one of the following measures:
1. Reorient or relocate the receiving antenna.
2. Relocate the fax machine with respect to receiver or other equipment.
3. Connect the fax machine into outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
War ni ng:To assure continued compliance, use only USB shielded interface cable when connecting this 
product to host computer. Also, any changes or modifications not expressly approved by the party 
responsible for compliance could void the users authority to operate this equipment.
This d evice complies with Part 1 5 of the FCC Rule s. Operation is subject to  the following two co nditions:
(1) This d evice ma y not ca use ha rmfu l interference, and 
(2) this device must accept any interference received, including interference that may cause undesired 
operation.
Note:Fo r Technical Support, plea se contact your Autho rized Panasonic de aler.
This e quipment complies with Part 68 of the FCC rules and th e requirements adop ted by the ACTA. 
On the rear panel of this equipment is a label that contains, among other information, a product 
identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the 
telephone company.
Ask your telephone company or installer to install the jack suitable for your device if such is not available.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply 
with the applicable  FCC Part 68 ru les and requ iremen ts a dopte d by th e ACTA. A compliant telep hone cord 
and modular plug is provided with this product. It is designed to be connected to a compatible modular jack 
that is also compliant. See installation instructions for details.
The  REN is used to de termine the nu mber of devices that ma y be conn ected to a te lephon e line. Excessive 
RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but 
not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may 
be co nnecte d to a line, as determin ed by the to tal RENs, con tact the local telephone  company. The REN for 
this product is part of the product ide ntifier that has the format US:AAAEQ##TXXXX. Th e digits represented 
by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
If your telephone equipment causes harm to the telephone network, the Telephone Company may 
discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice isnt 
practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with 
FCC.
Responsible Party: Panasonic Corporation of North America 
One Panasonic Way, Secaucus, NJ 07094  
FCC Inquiries Only: Panasonic Digital Document Company/Technical Support Department 
Two Panasonic Way, Secaucus, NJ 07094
1-800-225-5329 (see 
Note below)
Email: [email protected]
WARNING! 
						

							FCC Notice for Users in USA
148
Your telephone company may make changes in its facilities, equipment, operations or procedures that 
could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you 
an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact the manufacturers authorized 
service agency for information on obtainin g service or repairs. Th e tele phone company may ask that you 
disconnect this equipment from the network until the problem has been corrected or until you are sure that 
the equipment is not malfunctioning.
The optional Handset Kit is hea ring a id compatib le.
For protection again st the risk of ele ctric shock, always discon nect all cab les from the wall outlet before 
servicing, modifying or installing the equipment.
This eq uipment may not be used on coin service  provided by the tele phone compa ny n or conne cted to pa rty 
lines. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, 
public service commission or corporation commission for information.)
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of 
this equipment does not disable your alarm equipment. If you have questions about what will disable alarm 
equipment, consult your company or a qualified installer.
The Telep hone Consumer Protection Act of 1991 makes it unlawful for an y person to use a co mputer or 
other electronic device to send any message via telephone facsimile machine unless such message clearly 
contains in a margin at the top or bottom of each transmitted page or on the first page of transmission the 
fol low ing  i nformati on:
1. Date an d Time o f transmission.
2. Identification of either business, business entity or individual sending the message.
3. Telephone number of either the sending machine, business entity or individual.
In order to program this information into your facsimile machine, you should refer to page 26 in this 
Ope rating  Instructions to  comple te the  steps.
Example of Header Format (DATE a nd TIME, LOGO, ID Number setting)
MMM-dd-yyyy 09:00             PANASONIC                            201 348 7000           P.01/05
1) Date and Time               2) LOGO                              3) ID Number 
						

							149Appendix
Notice to Users in Canada
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of 
the local telecommunica tions company. The equipmen t must also be installed  using a n accep table  meth od 
of con nection. The  customer should be  aware  that compliance with the  above  conditions may not prevent 
degradation of service in some situations.
Repairs to this equipment should be made by an authorized Canadian maintenance facility designated by 
supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may 
give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, 
telephone lines and internal metallic water pipe system, if present, are connected together. This precaution 
may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but should contact the appropriate electric 
inspection authority, or electrician, as appropriate.
This equip ment me ets the  ap plicable Industry Ca nada Terminal Equipment Technical Specifications.  This is 
confirmed b y the registration number.  Th e abb reviation, IC, be fore the registra tion nu mber signifies that 
registration was performed based on a Declaration of Conformity indicating that Industry Canada Technical 
Specifications were met.  It does not imply that Industry Canada approved the equipment.
On the rear panel of this equipment is a label that contains, among other information, the Registration 
Number and Ringer Equivalence Number (REN) for this equipment.
The  REN assigne d to each  te rmina l e quipment provides an ind ication of the  maximum number of terminals 
allowed to be co nnecte d to a  teleph one interface.  The terminatio n on an interface may con sist of an y 
combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of 
all devices does not exceed five.
NOTICE
CAUTION!
NOTICE 
						

							Notice to Users in Canada
150
Avant dinstaller ce matériel, lutilisateur doit sassurer quil est permis de le raccorder aux installations de 
lentreprise locale de télécommunication.  Le matériel doit également être installé en suivant une méthode 
acceptée de raccordement.  Labonné ne doit pas oublier quil est possible que la conformité aux conditions 
énoncées ci-dessus nempêche pas la dégradation du service dans certaines situations.
Les réparations de ce matériel doivent être effectuées par un centre dentretien canadien autorisé désigné 
par le fournisseur.  La compagnie de télécommunications peut demander à lutilisateur de débrancher un 
appareil à la suite de réparations ou de modifications effectuées par lutilisateur ou à cause de mauvais 
fonctionnement.
Pour sa propre protection, lutilisateur doit sassurer que tous les fils de mise à la terre de la source 
dénergie électrique, des lignes téléphoniques et des canalisations deau métalliques, sil y en a, sont 
raccordé ensemble.  Cette précaution est particulièrement importante dans les régions rurales.
Lutilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service 
dinspection des installations électriques, ou à un électricien, selon le cas.   
Le présent matériel est conforme aux spécifications techniques d’Industrie Canada applicables au matériel 
terminal.  Cette conformité est confirmée par le numéro d’enregistrement.  Le sigle IC, placé devant le 
numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de 
conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées.  Il n’implique 
pas qu’Industrie Canada a approuvé le matériel.
Sur le panneau arrière de cet appareil se trouve une étiquette,  sur laquelle sont indiqués, entre autres, le 
numéro d’enregistrement et le numéro d’equivalence de sonnerie (IES) pour cet appareil.
L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être 
raccordés à une interface téléphonique.  La terminaison d’une interface peut consister en une combinaison 
quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous 
les dispositifs n’excède pas 5.
Avis
Avertissement!
Avis