Panasonic System Controller Wv Cu950 Addendum Information Manual

41
WJ-HD300 SERIES CONTROL (WV-CU950/650 TERMINAL MODE)
WJ-HD300 SERIES CONTROL (WV-CU950/650 PS·DATA)
Refer to p. 22 WJ-HD300 SERIES CONTROL (TERMINAL MODE).
Refer to p. 36 and the operating instructions of system controller. 

42
WJ-HD300 SERIES CONTROL (WV-CU360C/CJ TERMINAL MODE)
•Available operations are in common with WJ-HD500
Series. (Refer to this unit’s operating instructions.)
This document describes operations applicable to WJ-
HD300 Series only.
•You cannot control the following functions from System
Controller WV-CU360C and WV-CU360CJ. (It is recom-
mended to use System Controller WV-CU950 or WV-
CU650.)
•A – B repeat playback
•GO TO LAST
•Filtering ON/OFF
•MARK
•Text display ON/OFF
•Disk selection
•System...

43
4. To determine the filter setting, press the CAM (SET) but-
ton.
The searching filter window will be displayed on the
monitor.
Note:The searching filter window differs depending on
the searching filter selected in Step 3. Refer to
Searching filter windows for details on each win-
dow.
5. Filter recording events. (Refer to Searching filter win-
dows.)
6. To select a desired recording event, perform the follow-
ing.
•Move the joystick upward or downward.
•Press the NEXT or PREV button.
Note:To exit the...

44
(The list displayed in the window is the results of previ-
ous search.)
3. Press the CAM (SET) button.
The VMD search window will be displayed on the moni-
tor.
4. Enter a camera number and time range.
Available controls and functions 
Joystick:
Moves the cursor.
NEXT or PREV button:Changes a parameter.
PLAY button:Executes the VMD search and
returns to the upper menu.
MON (ESC) button:Cancels the filtering and
returns to the upper menu.
5. Press the CAM (SET) button.
The motion detection area setup...

45
12. Select the sensitivity by moving the joystick upward or
downward.
The sensitivity will be applied.
OFF:The motion detector is not activated on the
camera channel.
LOW:The sensitivity level is low.
MID:The sensitivity is level is medium.
HIGH:The sensitivity level is high.
13. To exit the motion detection area setup window, select
EXIT on the status bar by pressing the NEXT or PREV
button. Then, press the CAM (SET) button.
The motion detection mode setup window will be dis-
played on the monitor....

46
mm=Monitor No.
n=0:   Search playback*
n=1:   Time & date search playback**
* Transmission command changes the moni-
tor display as follows.
Date-and-time entry form
→Recording
event list 
→VMD search list →Marking list
→Date-and-time entry form...)
** Date-and-time entry form of matrix
switcher appears.
COMMUNICATION PROTOCOL (FOR USERS OF WJ-HD300 SERIES)
WJ-HD300 SERIES CONTROL (WV-CU360C/CJ PS·DATA)
Parameter (ASCII)
Stop
Index
Multiscreen segment switch-
ing
Item
CMD:RmmMLn
(Described as...

47
mm=Monitor No.
n=0   HDD normal/event recording sector
n=1   HDD copy sector
n=2   Disk connected to COPY 1
n=3   Disk connected to COPY 2
mm=Monitor No.
Setup control commands are available.
(
Refer to WJ-SX150A Operating
Instructions.
) WJ-HD300 Series OSD dis-
play ON
(Refer to WJ-SX150A
Operating Instructions for WJ-
SX150A OSD ON/OFF.)
ItemTransmission Command
(ASCII)Response (ASCII) Parameter (ASCII)
CMD:RmmDI ANS:RmmDI
DATA COPY window ON CMD:RmmPD ANS:RmmPD mm=Monitor No.
Setup control...

Panasonic Canada Inc.5770 Ambler Drive,Mississauga, 
Ontario, L4W 2T3 Canada (905)624-5010
http://www.panasonic.ca
Panasonic Sales CompanyDivision of Panasonic Puerto Rico Inc.San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina
P.R. 00985(809)750-4300
Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North AmericaSecurity Systems www.panasonic.com/security
For customer support, call 1.877.733.3689
Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey...