Panasonic System Controller Wv Cu950 Addendum Information Manual

31
3. Press the numeric buttons or +/– button to enter the
desired date and time.
The cursor can be adjusted by moving the 3D joystick
rightward or leftward.
4. Press the PLAY/PAUSE button. After the search through
the date and time, the recorded image will be played.
5. To return to the multiscreen display, press the STOP
button.
Note:To cancel the entry form, press the MON (ESC) or
EXIT button.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
1. Press the...

32
WJ-HD100 SERIES CONTROL  (TERMINAL MODE)MUX
Digital Disk Recorder WJ-HD100 Series are operable with
the system controller, when the Multiplexer board is
installed in the matrix switcher.
Note:Before the use, it is necessary to install the Multi-
plexer board in the matrix switcher, connect the
matrix switcher to the digital disk recorder, and con-
figure the system through WJ-SX150A Administrator
Console, OSD SETUP MENU, and WJ-HD100
Series SETUP MENU. (Refer to the operating
instructions of matrix...

33
3. Press the numeric buttons or +/– button to enter the
desired date and time. The cursor can be adjusted by
moving the 3D joystick rightward or leftward.
4. Press the PLAY/PAUSE button. After the search through
the date and time, the recorded image will be played.
5. To return to the multiscreen display, press the STOP
button.
Note:To cancel the entry form, press the MON (ESC) or
EXIT button.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
1. Press the...

34
TIME-LAPSE VCR CONTROL  [PANASONIC MODELS] (TERMINAL MODE)MUX
A time-lapse VCR (Panasonic Models) is operable with the
system controller, while connecting to the matrix switcher.
Note:Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the time-lapse VCR, and con-
figure the system through WJ-SX150A Administrator
Console, OSD SETUP MENU, and time-lapse VCRs
SETUP MENU. (Refer to the operating instructions
of matrix switcher.)
The...

35
TIME-LAPSE VCR CONTROL [NON-PANASONIC MODELS] (TERMINAL MODE)MUX
MONITOR DISPLAY CONTROL (PS·DATA)
A time-lapse VCR is operable with the system controller,
while connecting to the matrix switcher.
Notes:
•Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the digital disk recorder, and
configure the system through WJ-SX150A
Administrator Console, OSD SETUP MENU, and
time-lapse VCRs SETUP MENU. (Refer to the oper-
ating instructions...

36
WJ-HD500/300/200/100 SERIES CONTROL (PS·DATA)
The details on recorder control are described in WV-
CU950/WV-CU650 Operating Instructions. However, when
the system controller (WV-CU950 or WV-CU650) is con-
nected to recorders via the matrix switcher (WJ-SX150
Series), the following differences will occur.
■Unavailable Functions through
WJ-SX150A Connection
The following functions are unavailable when the system
controller (WV-CU950 or WV-CU650) is connected to
recorders via the matrix switcher...

37
■Connection with Digital Disk Recorder WJ-HD300 Series
Notes:
•Refer to service personnel for details on the connection with a recorder to operate via LAN or the Internet.
•Check that the firmware of recorder is Ver. 1.30 or later.
•Only one recorder can be connected to the DATA HDR connector of this unit. (Multiple unit connections, such as cascade
connection, are not available.) 
●Basic Connection
The following is the description of the connection between a recorder and this unit to confirm the...

38
●To Control a Recorder and Cameras via the Network
The following is the description of the connection between a recorder and this unit to control the recorder and cameras via the
network.
1. Set the unit address of the recorder to 5 or larger.
(Refer to the recorder’s operating instructions.)
2. Set the [Camera control] setting to “PSD” for all cameras in SETUP MENU of the recorder.
3. Connect the unit’s CAM OUT 1 to 16 connectors to the recorder’s VIDEO IN 1 to 16 connectors with a coaxial cable.
4....

39
●PS·Data Connection
1. Set the unit address of the recorder to 5 or larger.
2. Set the [Camera control] setting to “PSD” for all cameras in SETUP MENU of the recorder.
3. Connect the unit’s CAM OUT 1 to 16 connectors to the recorder’s VIDEO IN 1 to 16 connectors with a coaxial cable.
4. Connect the unit’s DATA4 Port connector to the recorder’s DATA port with a modular cable.
Select the recorder’s new unit address, which is set in Step 1, in 600 RECORDER of SETUP MENU or the Recorder window
of...

40
●Settings of Administrator Console and SETUP MENU(OSD)
When WJ-SX150A Administrator Console is Ver. 2.03 or later
Select “HD300”.
When the firmware of this unit is Ver. 2.03 or later.
Select “HD300” for “CONTROL” in 600 RECORDER of SETUP MENU(OSD).
■Connection with Digital Disk Recorder WJ-HD220 Series
●To Confirm the Images from a Recorder Connected to the Unit
•Connection procedures are the same as WJ-HD200 Series. (Refer to the operating instructions of matrix switcher.)
•Set the DATA setting to...