Panasonic System Controller Wv Cu950 Addendum Information Manual

							31
3. Press the numeric buttons or +/– button to enter the
desired date and time.
The cursor can be adjusted by moving the 3D joystick
rightward or leftward.
4. Press the PLAY/PAUSE button. After the search through
the date and time, the recorded image will be played.
5. To return to the multiscreen display, press the STOP
button.
Note:To cancel the entry form, press the MON (ESC) or
EXIT button.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
1. Press the ALM RECALL button. The ALARM RECALL
table will appear on the monitor.
2. Move the cursor with the 3D joystick to the desired
alarm number, and then press the PLAY/PAUSE button.
The associated image will be played back.
●Electronic Zooming (EL-ZOOM)
The operations are the same as WJ-HD500 Series. (Refer to
p. 21.)
Note:2 x and 4 x are available zooming range. 8 x is
unavailable.
●Multiscreen Sequence
The operations are the same as WJ-HD500 Series. (Refer to
p. 21.)
    ALARM RECALL  YEAR03
 NO.  DATE    TIME   ALM
 2000 JUN14 20:30:00  T1
 1999 JUN14 15:30:12  T3
 1998 JUN14 12:15:04  T4
 1997 JUN14 12:15:02  V8
 1996 JUN14 10:07:05  V2
 1995 JUN14 10:07:04  T2
 1994 JUN14 10:06:55  T6
 1993 JUN14 09:58:32  V5
(TOTAL  2000EVENTS)
 TO SEARCH PUSH T&D KEY 
						

							32
WJ-HD100 SERIES CONTROL  (TERMINAL MODE)MUX
Digital Disk Recorder WJ-HD100 Series are operable with
the system controller, when the Multiplexer board is
installed in the matrix switcher.
Note:Before the use, it is necessary to install the Multi-
plexer board in the matrix switcher, connect the
matrix switcher to the digital disk recorder, and con-
figure the system through WJ-SX150A Administrator
Console, OSD SETUP MENU, and WJ-HD100
Series SETUP MENU. (Refer to the operating
instructions of matrix switcher.)
■Displaying WJ-HD100 Series
SETUP MENU
The operations are the same as WJ-HD500 Series.
Refer to p. 18 Displaying WJ-HD500 Series SETUP MENU.
The following functions and buttons are valid in SETUP
MENU.
3D joystick to the left (A):Decrements a parameter
3D joystick to the right (B):Increments a parameter
■Controlling Digital Disk
Recorder WJ-HD100 Series
The following are the operating procedures of WJ-HD100
Series via the system controller.
●Multiscreen Segment Switching
The operating procedure is the same as WJ-HD500 Series.
(Refer to p. 19.) 
Note:7-, 10-, or 13-segment multiscreen display is unavail-
able.
●Normal Playback
The operations are the same as WJ-HD500 Series. (Refer to
p. 19.)
Notes:
•You cannot skip to the previous/next record.
•Refer to WJ-HD100 Series Operating Instructions for
details and other playback modes.
●Manual Recording
The operations are the same as WJ-HD500 Series. 
Refer to p. 20.
●Stopping REC ONLY Alarm
Recording
The operations are the same as WJ-HD500 Series. Refer to
p. 20.
●Search Playback
You can search playback images using the ALARM
RECALL table or the SEARCH table. 
Every time you press the SEARCH/T&D SEARCH button,
the display will change as follows.
Live image 
→Date-and-time entry form→ALARM RECALL
table 
→Live image
• Date-and-time Search Playback
The recorded images can be searched for through the date
and time.
1. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.)
2. Press the SEARCH/T&D SEARCH button. The date-and-
time entry form will appear on the center of the monitor.
Note:The factory default setting is the current date and
time.
                 SEARCH
            YYYY/MM/DD HH:MM
            2002/05/07 19:32 
						

							33
3. Press the numeric buttons or +/– button to enter the
desired date and time. The cursor can be adjusted by
moving the 3D joystick rightward or leftward.
4. Press the PLAY/PAUSE button. After the search through
the date and time, the recorded image will be played.
5. To return to the multiscreen display, press the STOP
button.
Note:To cancel the entry form, press the MON (ESC) or
EXIT button.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
1. Press the ALM RECALL button. The ALARM RECALL
table will appear on the monitor.
2. Move the cursor with the 3D joystick to the desired
alarm number, and then press the PLAY/PAUSE button.
The associated image will be played back.
   ALARM RECALL 1 OF 10
NO   DATE     TIME   ALM
99 JUN 9.00 00:00:00 * T
98 JUN 1.00 02:34:56   T
97 JUN 1.00 01:10:01 * V
96 MAY31.00 23:34:45   V
95 MAY30.00 02:00:20 * T
94 MAY14.00 05:30:31 * T
93 MAY 7.00 23:00:59   T
92 MAY 6.00 22:05:50   V
91 APR14.00 23:00:59 * T
90 APR14.00 16:06:34 * V 
						

							34
TIME-LAPSE VCR CONTROL  [PANASONIC MODELS] (TERMINAL MODE)MUX
A time-lapse VCR (Panasonic Models) is operable with the
system controller, while connecting to the matrix switcher.
Note:Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the time-lapse VCR, and con-
figure the system through WJ-SX150A Administrator
Console, OSD SETUP MENU, and time-lapse VCRs
SETUP MENU. (Refer to the operating instructions
of matrix switcher.)
The following is the procedure of a Panasonic model time-
lapse VCR.
■Controlling the Time-lapse VCR
The following are the operating procedures of the time-
lapse VCR via system controllers.
●Multiscreen Segment Switching
The operations are the same as WJ-HD500 Series. 
(Refer to p. 19.)
Note:7-, 10-, and 13- segment multiscreen display pat-
terns are unavailable.
●Normal Playback
The operations are the same as WJ-HD500 Series. 
(Refer to p. 19.)
Note:You cannot skip to the previous/next record.
●Fast-forward
1. During the stop, execute System Function 11. (Refer to
the operating instructions of system controller for how to
operate.) The tape will be fast-forwarded.
2. To stop fast-forwarding, press the STOP button.
Note:Pressing the PLAY/PAUSE button during fast-for-
ward will start playback.
●Rewind
1. During the stop, execute System Function 12. (Refer to
the operating instructions of system controller for how to
operate.) The tape will be rewinded.
2. Press the STOP button to stop rewinding.
Note:Pressing the PLAY/PAUSE button during rewind
will start playback.
●Manual Recording
The operations are the same as WJ-HD500 Series. 
Refer to p. 20 Manual Recording.
●Stopping REC ONLY Alarm
Recording
The operations are the same as WJ-HD500 Series. Refer to
p. 20. 
						

							35
TIME-LAPSE VCR CONTROL [NON-PANASONIC MODELS] (TERMINAL MODE)MUX
MONITOR DISPLAY CONTROL (PS·DATA)
A time-lapse VCR is operable with the system controller,
while connecting to the matrix switcher.
Notes:
•Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the digital disk recorder, and
configure the system through WJ-SX150A
Administrator Console, OSD SETUP MENU, and
time-lapse VCRs SETUP MENU. (Refer to the oper-
ating instructions of matrix switcher.)
•You cannot control non-Panasonic time-lapse VCRs
from system controllers.
The following is the procedure of a non-Panasonic model
time-lapse VCR.
■Controlling the Time-lapse VCR
●Multiscreen Segment Switching
The operations are the same as WJ-HD500 Series.
(Refer to p. 19.)
Note:7-, 10-, and 13- segment multiscreen display pat-
terns are unavailable.
●Normal Playback
1. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.)
2. Do the playback procedure using the buttons on the
front panel. (Refer to the time-lapse VCR’s operating
instructions for how to operate.)
3. Press the PLAY/PAUSE button. The playback image will
appear on the monitor.
4. To display the spot picture, press the numeric buttons
corresponding to the desired camera number, then
press the CAM (SET) button. Then, the active monitor
number will appear on the LCD. (Refer to p. 20 Normal
Playback for the illustration.)
●Other Operations
Refer to the time-lapse VCR’s operating instructions for how
to operate.
The operations are the same as System Controller WV-
CU360C/CJ.
(Refer to the operating instructions of matrix switcher for
how to operate.)
However, the following operations differ from System
Controller WV-CU360C/CJ.
■ On-screen Display (OSD)
Control
Refer to WV-CU950/650 Operating Instructions.
■ Video Loss History Table
Refer to WV-CU950/650 Operating Instructions. 
						

							36
WJ-HD500/300/200/100 SERIES CONTROL (PS·DATA)
The details on recorder control are described in WV-
CU950/WV-CU650 Operating Instructions. However, when
the system controller (WV-CU950 or WV-CU650) is con-
nected to recorders via the matrix switcher (WJ-SX150
Series), the following differences will occur.
■Unavailable Functions through
WJ-SX150A Connection
The following functions are unavailable when the system
controller (WV-CU950 or WV-CU650) is connected to
recorders via the matrix switcher (WJ-SX150 Series).
●HD500 V-Multi
●HD200 Alarm Search
■Functions Only Available with
WJ-HD300 Series
The following functions are available only when the system
controller (WV-CU950 or WV-CU650) is connected to WJ-
HD300 Series via the matrix switcher (WJ-SX150 Series).
●Time & Date Search Playback
■Functions Only Available with
WJ-HD200 Series/WJ-HD100
Series
The following functions are available only when the system
controller (WV-CU950 or WV-CU650) is connected to WJ-
HD200 Series or WJ-HD100 Series via the matrix switcher
(WJ-SX150 Series).
Note:This function is unavailable when the system con-
troller (WV-CU950 or WV-CU650) is connected to WJ-
HD500 Series via the matrix switcher (WJ-SX150
Series).
●Alarm Recall (WJ-HD200 Series)
The LCD display becomes as follows.
●Alarm Recall (WJ-HD100 Series)
The LCD display becomes as follows.
LCD MENU     HDD 204
HD500 V—Multi
Alarm Recall  /HD200
Edit
Alarm Recall  /HD100
J/S MENU         514
HD200 Alm Search
Mmm/DD/YYYY HH:MM 12
Mar/17/2004 12:00 AM 
						

							37
■Connection with Digital Disk Recorder WJ-HD300 Series
Notes:
•Refer to service personnel for details on the connection with a recorder to operate via LAN or the Internet.
•Check that the firmware of recorder is Ver. 1.30 or later.
•Only one recorder can be connected to the DATA HDR connector of this unit. (Multiple unit connections, such as cascade
connection, are not available.) 
●Basic Connection
The following is the description of the connection between a recorder and this unit to confirm the images from the recorder.
1. Set the unit address of the recorder to 1.
2. Set the [Camera control] setting to “PSD” for all
cameras in SETUP MENU of the recorder.
3. Connect the unit’s CAM OUT 1 to 16 connectors to
the recorder’s VIDEO IN 1 to 16 connectors with a
coaxial cable.
4. Connect the unit’s EXT IN connector to the
recorder’s MULTISCREEN OUT connector with a
coaxial cable.
5. Connect the unit’s DATA HDR connector to the
recorder’s DATA port with a modular cable.
Notes:
•Make sure the recorder’s unit address is set to 1
through SETUP MENU or WJ-SX150A administrator
Console. (Refer to this unit’s operating instructions.)
If another number is selected, you cannot control
the recorder.
•To control cameras at the front panel of recorder,
connect the DATA 4 connector and the DATA port
of recorder with a modular cable. (PS·Data system
controller is not connectable to the DATA 4 connec-
tor.)
•From system controllers connected to the unit (WJ-
SX150A), you cannot control the monitor connected
to the MONITOR OUT 1 connector of recorder. 
(2) ADDENDUM FOR MATRIX SWITCHER WJ-SX150 SERIES: TO USE
DIGITAL DISK RECORDER WJ-HD300 SERIES/WJ-HD220 SERIES
SIGNAL GND
POWER
AC IN
CAMERA1 12
23
3 2
DATA 3 DATA 2SERIAL ALARM
TERM
OFF ON42 14
3
CAMERA
SW  INRS485(CAMERA)LINE
SELECTMONITOR OUT
EXT IN
(PLAY IN)
EXT OUT
(REC OUT)
OUTIN
4 45
56
67
78
89
910
1011
1112
1213
1314
1415
1516
16
RS485(CAMERA)
DATA 4 DATA HDR
PS•DATADATA 1
1 2
IN
OUTCASCADE
OUT
16 16 315 1514
1413
2 113
12 1211
1110
109
98
87
76
65
54
43
32
21
1VIDEO
AUDIO IN AUDIO OUTMONITOR OUT CASCADE INMONITOR (VGA) ALARM/CONTOROLSERIAL ALARMPOWER COPY 1 MODEEXT STORAGE 10/100BASE-T RS485(CAMERA)DATAAC  IN
SIGNAL GND1
42
System controller
(Terminal Mode)
EXT IN
MONITOR OUT
Matrix Switcher
Recorder** DATA 4 *
(PS·Data) DATA HDR
MONITOR OUT x
DATA
* Connect these ports if you control cameras from the front panel of recorder.
** Set the recorder’s unit address to 1.Monitor
SYSTEM CONNECTIONS AND SETUPS (WJ-HD300 SERIES/WJ-HD220 SERIES) 
						

							38
●To Control a Recorder and Cameras via the Network
The following is the description of the connection between a recorder and this unit to control the recorder and cameras via the
network.
1. Set the unit address of the recorder to 5 or larger.
(Refer to the recorder’s operating instructions.)
2. Set the [Camera control] setting to “PSD” for all cameras in SETUP MENU of the recorder.
3. Connect the unit’s CAM OUT 1 to 16 connectors to the recorder’s VIDEO IN 1 to 16 connectors with a coaxial cable.
4. Connect the unit’s EXT IN connector to the recorder’s MULTISCREEN OUT connector with a coaxial cable.
5. Connect the unit’s DATA HDR and DATA4 connectors to the recorder’s DATA ports with modular cables.
6. Select the recorder’s new unit address, which is set in Step 1, in 600 RECORDER of SETUP MENU or the Recorder window
of WJ-SX150A Administrator Console. (Refer to this unit’s operating instructions.)
Notes:
•Select the PS·Data protocol for the DATA 4 setting.
(Refer to this unit’s operating instructions.)
•If the recorder’s unit address, set in Step 1, and the recorder setting, set in Step 6, are different, the recorder will not be
operable.
•In these connections, you cannot use a PS·Data system controller.
•From system controllers connected to the unit, you cannot control the monitor connected to the MONITOR OUT 1 connec-
tor of recorder.
SIGNAL GND
POWER
AC IN
CAMERA1 12
23
3 2
DATA 3 DATA 2SERIAL ALARM
TERM
OFF ON42 14
3
CAMERA
SW  INRS485(CAMERA)LINE
SELECTMONITOR OUT
EXT IN
(PLAY IN)
EXT OUT
(REC OUT)
OUTIN
4 45
56
67
78
89
910
1011
1112
1213
1314
1415
1516
16
RS485(CAMERA)
DATA 4 DATA HDR
PS•DATADATA 1
1 2
IN
OUTCASCADE
OUT
16 16 315 1514
1413
2 113
12 1211
1110
109
98
87
76
65
54
43
32
21
1VIDEO
AUDIO IN AUDIO OUTMONITOR OUT CASCADE INMONITOR (VGA) ALARM/CONTOROLSERIAL ALARMPOWER COPY 1 MODEEXT STORAGE 10/100BASE-T RS485(CAMERA)DATAAC  IN
SIGNAL GND1
42
EXT IN
MONITOR OUT
DATA 4
(PS·Data) DATA HDR
Matrix Switcher
Recorder*
HUB/Router MONITOR OUT x
DATA
* Set the recorder’s unit address to 5 or larger.
** LAN: Local Area Network
LAN**
System controller
(Terminal Mode)Monitor 
						

							39
●PS·Data Connection
1. Set the unit address of the recorder to 5 or larger.
2. Set the [Camera control] setting to “PSD” for all cameras in SETUP MENU of the recorder.
3. Connect the unit’s CAM OUT 1 to 16 connectors to the recorder’s VIDEO IN 1 to 16 connectors with a coaxial cable.
4. Connect the unit’s DATA4 Port connector to the recorder’s DATA port with a modular cable.
Select the recorder’s new unit address, which is set in Step 1, in 600 RECORDER of SETUP MENU or the Recorder window
of WJ-SX150A Administrator Console. (Refer to this unit’s operating instructions.)
Notes:
•Select the PS·Data protocol for the DATA 4 setting.
(Refer to this unit’s operating instructions.)
•If the recorder’s unit address, set in Step 1, and the recorder setting, set in Step 5, are different, the recorder will not be
operable.
•Do not connect the recorder to the DATA HDR port.
•From system controllers connected to the unit, you cannot control the recorder.
•Only one matrix switcher can be connected in the PS·Data mode.
SIGNAL GND
POWER
AC IN
CAMERA1 12
23
3 2
DATA 3 DATA 2SERIAL ALARM
TERM
OFF ON42 14
3
CAMERA
SW  INRS485(CAMERA)LINE
SELECTMONITOR OUT
EXT IN
(PLAY IN)
EXT OUT
(REC OUT)
OUTIN
4 45
56
67
78
89
910
1011
1112
1213
1314
1415
1516
16
RS485(CAMERA)
DATA 4 DATA HDR
PS•DATADATA 1
1 2
IN
OUTCASCADE
OUT
16 16 315 1514
1413
2 113
12 1211
1110
109
98
87
76
65
54
43
32
21
1VIDEO
AUDIO IN AUDIO OUTMONITOR OUT CASCADE INMONITOR (VGA) ALARM/CONTOROLSERIAL ALARMPOWER COPY 1 MODEEXT STORAGE 10/100BASE-T RS485(CAMERA)DATAAC  IN
SIGNAL GND1
42
MONITOR OUTMonitor
Monitor Monitor System controller
(Terminal Mode)*
System controller
(PS·Data) DATA 4 *
(PS·Data)
MONITOR 
OUT x MONITOR 
OUT zDATAMatrix Switcher
Recorder*
* Recorder control from system controllers connected to the matrix switcher is not available. 
						

							40
●Settings of Administrator Console and SETUP MENU(OSD)
When WJ-SX150A Administrator Console is Ver. 2.03 or later
Select “HD300”.
When the firmware of this unit is Ver. 2.03 or later.
Select “HD300” for “CONTROL” in 600 RECORDER of SETUP MENU(OSD).
■Connection with Digital Disk Recorder WJ-HD220 Series
●To Confirm the Images from a Recorder Connected to the Unit
•Connection procedures are the same as WJ-HD200 Series. (Refer to the operating instructions of matrix switcher.)
•Set the DATA setting to “PSD” for CAMERA 1 to 4 in the CAMERA SYSTEM SETUP menu of the recorder.
●To Control a Recorder via the Network
•Connection procedures are the same as WJ-HD200 Series.
•Set the DATA setting to “PSD” for CAMERA 1 to 4 in the CAMERA SYSTEM SETUP menu of the recorder.
●Settings of Administrator Console and SETUP MENU(OSD)
Select “HD200” in the Administrator Console window.
 600 RECORDER
             CONTROL   ADR   EXT IN
 610 MASTER  ---
 620 SLAVE1  HD300      01   GENLOCK OFF
 630 SLAVE2  HD300      01   GENLOCK OFF
 640 SLAVE3  HD100      01
 650 SLAVE4  OFF             GENLOCK OFF
   --COMMUNICATION STATUS--
     DATA BIT      7bit
     PARITY BIT    ODD
     STOP BIT      1bit
     BAUD RATE      9600bps
     COMM PORT     SERIAL PORT