Panasonic System Controller Wv Cu950 Addendum Information Manual

This operation is skipped when the auto login is set to ON.
(Refer to the operating instructions of matrix switcher.)
1. Turn on the power switches of all system components.
The OPERATE indicator will light up.
2. To turn on the power of the system controller, connect
the AC adapter to the AC outlet.
The OPERATE indicator lights up and Terminal Mode
No User appears on the LCD.
BEFORE OPERATION
INSTALLATIONS AND CONNECTIONS
SETUP PROCEDURES (HARDWARE)
Note: This section describes the terminal mode. To...

2
■ Operation End (Logout)
This operation is skipped when the auto logout is set to ON. 
This function is used when an operator leaves the controller
or no longer requires access to the system.
To log out of the system, press the MON LOCK/LOGOUT
button while holding down the SHIFT button.
Logout will blink on the LCD for about 3 seconds. Then,
Terminal Mode No User appears on the LCD.
Note:If you want to save the power consumption, discon-
nect the DC 9 V plug from the controller, and remove
the AC...

3
● Releasing Priority Lock
1. Select the desired monitor. (Refer to Monitor Selection.)
2. Press the MON LOCK/LOGOUT button to release the
priority lock mode.
The monitor number returns to the normal display on
the active monitor.
■ Camera Selection
1. Select the desired monitor. (Refer to Monitor Selection.)
2. Press the numeric buttons to select the desired camera
number (1 to 99).
3. Press the CAM (SET) button.
The selected cameras image will appear on the active
monitor, and the selected camera...

4
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
Buttons and control for cameras or camera site accessories
are located on the 3D joystick unit and the right side of
main unit.
Included are zoom control, focus control, iris control, preset
and pan/tilt controls. 
Normally, combination cameras equipped with the specific
feature or a WV-RC100 or WV-RC150 Receiver are required
to utilize these functions.
Note:Refer to the cameras...

5
■ Program Preset Position
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. To move the camera to the position to be preset, move
the 3D joystick and press the lens control buttons.
3. To select the desired preset position number, press the
numeric buttons. (1 to 64)
4. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
5. Press the PRESET/PGM PRESET button while holding
down the SHIFT button to save a preset...

6
■ Camera Function (Shortcut
Function)
The following function is available only when specified cam-
eras with the camera function feature are used.
This function enables executing camera functions via a
shortcut.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the numeric buttons to select an assigned func-
tion number, then press the CAM FUNC/SYS FUNC but-
ton.
For example, enter 175 for AGC ON.
The selected function will be executed on...

7
■ Patrol Learn and Play
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. To save the patrol sequence, follow the procedure
below.
qPress the MENU button repeatedly until Patrol
Learn will appear on the LCD.
wPress the F1 button.
eOperate the camera manually. 
rPress the F2 button.
The operation data will be saved.
3. To reproduce the operation...

8
■ Changing to Black and White
Images
This function gets the clear camera images on the monitor
while shooting the objects under low light conditions.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the MENU button repeatedly until BW Mode
appears on the LCD.
3. Press the F1 button to change the image from the color
mode to the BW (black and white) mode on the active
monitor.
4. Press the F2 button to change the BW image to the
color image...

9
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
■Receiver Control
The following functions are available only when the
receivers are included in the system and the specified
camera housing is installed.
● Camera Housing Control
Wiper Control
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the WIPER button to turn on the housing wiper of
the camera repeatedly until buttons...

10
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
■ Tour Sequence
The following functions are available if a tour sequence has
been previously configured through SETUP MENU or WJ-
SX150A Administrator Console. Any tour sequence can be
assigned to any monitors.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. To select the desired tour sequence number, press the
numeric buttons....