Panasonic System Controller Wv Cu950 Addendum Information Manual

21
• Record List/Thumbnail Display
You can operate the Record List or Thumbnail Display by
referring to the recorder’s operating instructions. In addi-
tion, the following operations from the system controllers
are also available.

Shuttle ring clockwise:
Moves to the next page.
Shuttle ring counterclockwise:Moves to the previous
page.
JogDial clockwise or counterclockwise:Moves the
cursor.
+ or – button:Moves the cursor.
CAM (SET) button:Displays the search editing area. /
Starts the search after you...

22
Matrix switcher can control the following functions of Digital
Disk Recorder WJ-HD300 Series. The following is the pro-
cedure of WJ-HD300 Series SETUP MENU.
Notes:
•The following operating procedures are for the terminal
mode. If you are using a PS·Data system controller,
refer to p. 36.
•
When a Multiplexer board is installed in the matrix switch-
er, you can neither connect nor control a WJ-HD300 Series
recorder. You need to remove the board from the matrix
switcher.
•Some parts of monitor...

23
●Normal Playback
The operations are the same as WJ-HD500 Series. (Refer to
p. 19.)
Note:Refer to the recorder’s operating instructions for
details and other playback modes.
●Manual Recording
The operations are the same as WJ-HD500 Series. (Refer to
p. 20.)
●Stopping REC ONLY Alarm
Recording
The operations are the same as WJ-HD500 Series. (Refer to
p. 20.)
■Search Playback
You can search recorded images through the date and
time. 
Every time you press the SEARCH/T&D SEARCH button in
the recorder mode,...

24
• Recording event search
You will select a searching filter from TIME&DATE, CAM-
ERA, REC EVENT, and TEXT. Playback pictures will be
searched by the selected searching filter. 
1. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.)
2. Repeat pressing the SEARCH/T&D SEARCH button
until the recording event list window is displayed on the
monitor. The recorder will enter the searching mode.
3. Select a desired searching filter by moving the joystick
rightward or leftward.
Note: The illustration is...

25
7. Select a desired recording event by performing one of
the following.
•Move the 3D joystick controller to up or down.
•Rotate the JogDial clockwise or counterclockwise.
•Press the + or – button.
Note:To move to the next or previous page, perform
either of the following.
•Move the zoom wheel controller to the right or left.
•Rotate the shuttle ring clockwise or counterclock-
wise.
8. Press the PLAY button.
The playback of selected recording event will start.
9. To exit the search mode, press the MON...

26
• VMD search
Recording events will be searched by the date and time
when a camera detected the brightness-level change.
Then, a result list or a thumbnail will be displayed.
For playback, you will select a time and date displayed on
the result list or thumbnail. Filtering is available by camera
channel, date-and-time, detection area or search mode.
1. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.)
2. Repeat pressing the SEARCH/T&D SEARCH button
until the VMD search  list window is displayed...

Note:To delete the motion detection area, select
DELETE AREA on the status bar by rotating the
JogDial  or pressing the +/– button. Then, move the
+ mark to the desired area with the joystick, and
press the CAM (SET) button.
10. Select SENSITIVITY on the status bar by performing
either of the following.
•Rotate the JogDial clockwise or counterclockwise.
•Press the + or – button.
Note:Depending on the position of the set detection
areas, the sensitivity indications of the detection
areas may be displayed...

28
■Disk Selection
You will specify a disk of recorder for search playback.
1. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.)
2. Press the MENU button repeatedly repeatedly until
HD300 DiskSelect appears on the LCD.
3. Press one of the F1 to F4 buttons.
The specified disk will be selected.
Available buttons and functions
F1: Nr-A
Specifies the normal or event recording area for play-
back.
F2: Cp-A
Specifies the copy area for playback.
F3: Cpy1
This button is reserved for future use.
F4: Cpy2...

29
Note:To cancel the setting and exit HD300 A – B
repeat, press the MON (ESC) or EXIT button. The
LCD display will return to the default status.
3. During playback, press the F1 button at the point you
wish to start playback. The playback start point (A) will
be set.
Note:To cancel the start point, press the F4 button.
4. Press the F2 button at the point you wish to end play-
back. The playback end point (B) will be set, and the
repeat playback will be performed between (A) and (B).
■Canceling Filters...

30
WJ-HD200 SERIES CONTROL (TERMINAL MODE)
Matrix switcher can control the following functions of Digital
Disk Recorder WJ-HD200 Series. The following is the pro-
cedure of WJ-HD200 Series SETUP MENU.
Notes:
•The following operating procedures are for the terminal mode.
If you are using a PS·Data system controller, refer to p. 36.
•When a Multiplexer board is installed in the matrix switch-
er, you can neither connect nor control a WJ-HD200 Series
recorder. You need to remove the board from the matrix...