Panasonic System Controller Wv Cu950 Addendum Information Manual

							This operation is skipped when the auto login is set to ON.
(Refer to the operating instructions of matrix switcher.)
1. Turn on the power switches of all system components.
The OPERATE indicator will light up.
2. To turn on the power of the system controller, connect
the AC adapter to the AC outlet.
The OPERATE indicator lights up and Terminal Mode
No User appears on the LCD.
BEFORE OPERATION
INSTALLATIONS AND CONNECTIONS
SETUP PROCEDURES (HARDWARE)
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
Before starting the following procedures, all system compo-
nents must be turned on.
The following procedures are applicable when the system
controller is connected to the matrix switcher.
■ Operation Start (Login)
Note:When auto login is set to ON, operators can log into
the system without entering their passwords. (Refer to
p. 2 Operation Start (Auto Login).)Terminal Mode
No User
Addendum for WV-CU950/650 and WJ-SX150 Series
(1) ADDENDUM FOR SYSTEM CONTROLLER WV-CU950/WV-CU650: 
MATRIX SWITCHER WJ-SX150 SERIES 
OPERATING PROCEDURES
The descriptions in this document are applicable when WJ-SX150A Administrator Console and the firmware of this unit (matrix
switcher) are Ver. 2.04 or later.
Note:Refer to the operating instructions of matrix switcher for how to check the version.
■Basic System Connections
•The connection details are the same as System
Controller WV-CU360C/CJ. Refer to the operating
instructions of matrix switcher .
•
To connect System Controller WV-CU950 or WV-CU650
to Digital Disk Recorder WJ-HD300 Series or WJ-HD220
Series via the matrix switcher, refer to pp. 37 to 40.
■MODE Switch Setting
Either of the terminal mode or PS·Data mode are applicable
for connections. Refer to WV-CU950/WV-CU650 Operating
Instructions for details on the switch setting for each mode.
■CONTROLLER NO. Switch
Setting
Normally, set this switch to “1” (default position). 
						

							2
■ Operation End (Logout)
This operation is skipped when the auto logout is set to ON. 
This function is used when an operator leaves the controller
or no longer requires access to the system.
To log out of the system, press the MON LOCK/LOGOUT
button while holding down the SHIFT button.
Logout will blink on the LCD for about 3 seconds. Then,
Terminal Mode No User appears on the LCD.
Note:If you want to save the power consumption, discon-
nect the DC 9 V plug from the controller, and remove
the AC adapter from the AC outlet.
■ Operation End (Auto Logout)
If the auto logout is set to ON and no operation takes place
for a specific time, any operators can logout automatically.
After the logout, Terminal Mode No User automatically
appears on the LCD.
You can activate auto logout and set up the duration until
logout (configurable by minute) through WJ-SX150A
Administrator Console. (Refer to the operating instructions
of matrix switcher.) 3. To select your registered operator ID number (1 to 16,
up to 2 digits), press the numeric buttons, then press
the CAM (SET) button.
Password entry form appears on the LCD.
Note:The factory default setting is 150.
4. To select your registered password (up to 5 digits),
press the numeric buttons, then press the CAM (SET)
button.
The factory default setting is 150.
If the operator ID and password are correct, Login OK
will blink on the LCD for about 3 seconds. Then, Mon -
Cam - - will appear on the LED display.
Note:If an operator ID or password error occurs,
Invalid will blink on the LCD for about 3 seconds.
Then, return to Step 3 and select your operator ID.
■ Operation Start (Auto Login)
If the auto login is set to ON, any operators can log into the
system automatically. After the controller is turned on, Auto
Login appears on the LCD for approximately 2 seconds,
then Mon - Cam - - automatically appears.
Auto login is configurable through WJ-SX150A
Administrator Console. (Refer to the operating instructions
of matrix switcher.)
Mon-  Cam--
User ID          150
Password       __∗∗∗
Mon-  Cam--
      Invalid
Blinking
Terminal Mode
No User
Terminal Mode
No User
User ID          150
Password       _____ 
						

							3
● Releasing Priority Lock
1. Select the desired monitor. (Refer to Monitor Selection.)
2. Press the MON LOCK/LOGOUT button to release the
priority lock mode.
The monitor number returns to the normal display on
the active monitor.
■ Camera Selection
1. Select the desired monitor. (Refer to Monitor Selection.)
2. Press the numeric buttons to select the desired camera
number (1 to 99).
3. Press the CAM (SET) button.
The selected cameras image will appear on the active
monitor, and the selected camera number will appear
on the LCD.
Note:If you have entered a wrong camera number,
press the CLEAR button to clear the input.
4. If the selected camera number is not valid, Prohibited
and the camera number will blink on the LCD for about
3 seconds.
In this case, return to Step 2 and select another camera
number.
Note:If the camera is selected by an operator with
higher priority, Prohibited will also blink on the
LCD.
5. To replace the currently selected camera with the next
higher-numbered camera , press the + button.
To replace the currently selected camera with the next
lower-numbered camera, press the – button.
Note:Cameras selected by operators with higher priori-
ty will be skipped.
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
After the login procedure, the following operations are avail-
able to control the system.
The operation begins with monitor selection. Then, the
image of selected camera appears on the active monitor.
■ Monitor Selection
1. To select the desired monitor number (1 to 4), press the
numeric button.
2. Press the MON (ESC) button to execute the selection.
The selected monitor number will appear on the LCD.
3. If the selected monitor number is not valid, or if an oper-
ator with higher priority is controlling the monitor, the
monitor number and Prohibited will blink on the LCD
for approximately 3 seconds.
In this case, return to Step 1 and select another monitor
number.
■ Priority Lock
● Applying Priority Lock
1. Select the desired monitor. (Refer to Monitor Selection).
2. Press the MON LOCK/LOGOUT button to toggle the pri-
ority lock mode on and off on the active monitor.
If the priority lock mode is selected, the monitor number
will inversely appear on the active monitor as shown in
the figure.
Note:This function will prevent operators with lower priority
from gaining control of a monitor.
However, higher or equal priority operators may still
gain control of the monitor.
Mon1  Cam--
MONITOR SELECTION AND CAMERA SELECTION
Mon1  Cam03
Mon1  Cam03
Mon1  Cam04
Mon-  Cam--
          Prohibited
Blinking
M04M04 
						

							4
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
Buttons and control for cameras or camera site accessories
are located on the 3D joystick unit and the right side of
main unit.
Included are zoom control, focus control, iris control, preset
and pan/tilt controls. 
Normally, combination cameras equipped with the specific
feature or a WV-RC100 or WV-RC150 Receiver are required
to utilize these functions.
Note:Refer to the cameras operating instructions whether
to confirm that each function is available.
■ Lens Control
This function is available when specified lens, with motor-
ized zoom/focus functions, is mounted on the camera, and
the lens selection (DC/VIDEO) on the camera is set to DC.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the FOCUS FAR or NEAR button while watching
the monitor. The lens focus is adjusted to obtain a
sharply focused image.
Note:Pressing the B button or top button of 3D joystick
unit can also set the lens focus automatically.3. To adjust the lens zoom, move the zoom wheel con-
troller to the right (TELE) or left (WIDE).
4. Press the IRIS OPEN or CLOSE buttons to open/close
the lens iris. The lens iris is adjusted by these buttons to
obtain the proper image exposure.
Note:To set the lens iris automatically, press the A but-
ton of 3D joystick unit.
■ Pan/Tilt Control
● Manual Operation
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Move the 3D joystick to move the pan/tilt head towards
the desired direction.
● Auto Panning
Refer to p. 8 Camera Panning Function for how to oper-
ate.
CAMERA CONTROL
FA R
FOCUS
NEAR
OPEN
IRIS
CLOSE
Top button
WIDE
TELE
Zoom wheel controller 
						

							5
■ Program Preset Position
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. To move the camera to the position to be preset, move
the 3D joystick and press the lens control buttons.
3. To select the desired preset position number, press the
numeric buttons. (1 to 64)
4. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
5. Press the PRESET/PGM PRESET button while holding
down the SHIFT button to save a preset position of the
selected camera.
Notes:
•If the entered position number has stored the previ-
ous preset position, it will be overwritten by the new
one.
•SETUP MENU and WJ-SX150A Administrator
Console can configure each operators pan/tilt con-
trol. (Refer to the operating instructions of matrix
switcher.)
■ Call Preset Position
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. To select the desired preset position number, press the
numeric buttons. (1 to 64)
3. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
4. Press the PRESET/PGM PRESET button to move to the
preset position of the selected camera on the active
monitor.
Notes:
•To use the above function, you must set the preset
position number for the camera.
•If you press no numeric buttons or the button 0 in
Step 2, the camera will move to the home position.
Mon1  Cam03    Pre48
       Memory
Mon1  Cam03    Pre05 
						

							6
■ Camera Function (Shortcut
Function)
The following function is available only when specified cam-
eras with the camera function feature are used.
This function enables executing camera functions via a
shortcut.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the numeric buttons to select an assigned func-
tion number, then press the CAM FUNC/SYS FUNC but-
ton.
For example, enter 175 for AGC ON.
The selected function will be executed on the active
monitor.
Notes:
•When you select a wrong number, press the CLEAR
button to clear the numeric input.
•Refer to the cameras operating instructions for
details on available shortcuts.
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
■Camera Setup
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the MENU button repeatedly until Camera Setup
appears on the LCD.
3. Press the F1 button. The cameras SETUP MENU will
appear on the active monitor.
4. To select the desired item in the menu, move the 3D
joystick to 
Cor D. To select the desired parameter (or
mode) in the menu, move the 3D joystick to 
Aor B.
5. To execute the currently highlighted selection and to
enter a submenu of SETUP MENU, press the CAM
(SET) button.
6. To leave from the currently selected menu and to return
to the previous page of the menu, press the MON (ESC)
button.
7. Move the cursor to SPECIAL on the camera’s setup
menu, and press the F3 button to display the special
menu.
8. Move the cursor to CAMERA RESET on the camera’s
setup menu, and press the F4 button to reset all the
functions to the defaults.
Note:Refer to the operating instructions of the selected
camera for details.
9. To close the cameras SETUP MENU, press the F2 but-
ton.
10. To exit the mode, press the MON (ESC) button.
CAMERA FUNCTION CONTROL
Camera Setup     006
  On  Off  Rst A.Rst
Camera Setup     006
 
5On  Off  Rst A.Rst 
						

							7
■ Patrol Learn and Play
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. To save the patrol sequence, follow the procedure
below.
qPress the MENU button repeatedly until Patrol
Learn will appear on the LCD.
wPress the F1 button.
eOperate the camera manually. 
rPress the F2 button.
The operation data will be saved.
3. To reproduce the operation data, follow the procedure
below.
qPress the MENU button repeatedly until Auto
Mode appears on the LCD.
wPress the F4 button.
eTo stop the reproduction, move the 3D joystick.
4. To exit the mode, press the MON (ESC) button.
Patrol Learn     007
Start Stop
Auto Mode        009
 Seq Sort Pan Patrol
■Auto Pan Setup and Activation
You will set up and activate the auto pan function. The cam-
era can pan between the start and end points you will set.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the MENU button repeatedly until Auto Pan
Setup appears on the LCD.
3. To set the start and end point of auto pan, perform the
following.
qTo move the camera to a point you wish to start
auto pan, move the 3D joystick and press the lens
control buttons (IRIS OPEN and CLOSE, FOCUS
FAR and NEAR).
wPress the F3 button.
The start point of auto pan will be set.
eTo move the camera to a point you wish to end auto
pan, move the 3D joystick.
rPress the F4 button.
The end point of auto pan will be set.
Auto Pan Setup   008
Play Rvrs Start End 
						

							8
■ Changing to Black and White
Images
This function gets the clear camera images on the monitor
while shooting the objects under low light conditions.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the MENU button repeatedly until BW Mode
appears on the LCD.
3. Press the F1 button to change the image from the color
mode to the BW (black and white) mode on the active
monitor.
4. Press the F2 button to change the BW image to the
color image on the active monitor.
5. Press the MON (ESC) button to exit the mode.
■ Camera Panning Function
There are three panning modes available as follows:
sequence mode, sort mode, and auto pan. (Refer to the
operating instructions of matrix switcher.)
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the MENU button repeatedly until Auto Mode
appears on the LCD.
3. Press the assigned function button to activate the pan-
ning function of the selected camera.
The LCD will indicate the selected mode as follows.
F1:Seq (Activates SEQUENCE PAN.)
F2:Sort (Activates SORT PAN.)
F3:Pan (Activates AUTO PAN.)
Note:The AUTO MODE parameter, previously set in
the cameras SETUP MENU, will be automatically
replaced to the activated function parameter.
4. To exit the mode, press the MON (ESC) button.
BW Mode          010
  On Off Auto1 Auto2Auto Mode        009
 Seq Sort Pan Patrol 
						

							9
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
■Receiver Control
The following functions are available only when the
receivers are included in the system and the specified
camera housing is installed.
● Camera Housing Control
Wiper Control
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the WIPER button to turn on the housing wiper of
the camera repeatedly until buttons are released.
Defroster Control
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the DEF ON/OFF button to turn on the housing
defroster of the camera.
3. To turn off the defroster, press the DEF ON/OFF button
while holding down the SHIFT button.
● Auxiliary Control
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the AUX1 ON/OFF button to turn on the users
auxiliary switch 1 of the receiver.
Press the AUX1 ON/OFF button while holding down the
SHIFT button to turn off the users auxiliary switch 1 of
the receiver.
3. Press the AUX2 ON/OFF button to turn on the users
auxiliary switch 2 of the receiver.
Press the AUX2 ON/OFF button while holding down the
SHIFT button to turn off the users auxiliary switch 2 of
the receiver.
CAMERA SITE ACCESSORIES CONTROL 
						

							10
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
■ Tour Sequence
The following functions are available if a tour sequence has
been previously configured through SETUP MENU or WJ-
SX150A Administrator Console. Any tour sequence can be
assigned to any monitors.
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. To select the desired tour sequence number, press the
numeric buttons.
3. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
4. Press the TOUR SEQ/GROUP SEQ button to run the
tour sequence in the forward direction on the active
monitor.
5. Press the SEQ PAUSE/SEQ STOP button to pause a
tour sequence on the active monitor.
The P sign (indicating the pause status) is displayed
at the tour sequence number on the active monitor, and
a camera number currently selected appears on the
LCD.
•Press the SEQ PAUSE/SEQ STOP button to restart a
tour sequence forward from the next step that was pre-
viously paused.
•Press the + button to move the sequence one frame to
the next step from the step that was previously paused.
•Press the – button to move the sequence one frame to
the previous step from the step that was previously
paused.
6. Press the SEQ PAUSE/SEQ STOP button while holding
down the SHIFT button to stop a tour sequence on the
active monitor and return to spot monitoring.
■ Group Sequence
The following function is available only if a group sequence
has been previously established in WJ-SX150A
Administrator Console.
A group sequence determines the assignment of monitors
and cameras. Therefore, monitor selection is not required.
1. Press the numeric buttons to select a desired group
sequence number.
2. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
3. Press the TOUR SEQ/GROUP SEQ button while holding
down the SHIFT button to run a group sequence for-
ward on the assigned monitors.
4. Press the SEQ PAUSE/SEQ STOP, + or – button to
operate the group sequence. Refer to Step 5 of Tour
Sequence in this page for how to use these buttons. 
5. To stop the sequence, select one of the monitors that
are being run on the selected group sequence, then
press the SEQ PAUSE/SEQ STOP button while holding
down the SHIFT button
Note:If an alarm is activated during a sequence pause, the
sequence runs again after the matrix switcher recovers
from the alarm mode.
RUNNING SEQUENCE
Mon1  Cam01
                T04
Mon1  Cam07
                T04P
Mon1  Cam01
                T01