Panasonic System Controller Wv Cu950 Addendum Information Manual

							11
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to p. 35.
■ On-screen Display (OSD)
Control
The procedure described below lets you determine the dis-
play parameters, such as camera title, clock and status, on
and off on the active monitor screen.
Before controlling each item, monitor selection is neces-
sary. (Refer to p. 3 Monitor Selection.)
●Displaying Each Item
1. Press the MENU button repeatedly until OSD On/Off
appears on the LCD.
2. Perform desired operations.
qDisplaying the clock
Toggle the F1 button.
(1) will appear/disappear on/from the active moni-
tor.
wDisplaying the camera title
Toggle the F2 button.
(2) will appear/disappear on/from the active moni-
tor.
eDisplaying the event
Toggle the F3 button.
(3) will appear/disappear on/from the active moni-
tor.
rDisplaying the monitor status*
Toggle the F4 button.
(4)* will appear/disappear on/from the active moni-
tor.
*Monitor number, system controller name, tour num-
ber and recorder number3. To exit the mode, press the MON (ESC) button.
●Displaying All the Items
1. Perform Step 1 of Displaying Each Item.
2. Hold down the SHIFT button.
The LCD display will become as follows.
3. Press the F1 button.
(1), (2), (3), and (4) will appear/disappear on/from the
active monitor. 
■ On-screen Display (OSD)
Position Control
The procedure described below lets you determine the dis-
play positions, such as camera title, clock and status, on
the active monitor screen.
●Moving Each Item
1. Press the MENU button repeatedly until OSD Position
appears on the LCD.
MONITOR DISPLAY CONTROL
08/21/2002 12:50:28 PM
M1  K1 T01
C01 camera title          ALARM10*(1)
(3) (4)
(2)
OSD On/Off       002
Clock Cam Event Mon
08/21/2002 12:50:59 PM
M1  K1 T01
C01 camera title          ALARM10*
Camera title
Monitor statusEvent
Clock
OSD Position     003
Clock Cam Event Mon
OSD On/Off       002
 All 
						

							12
2. Press the MENU button repeatedly until System Status
appears on the LCD.
3. Press the F1 button. 
The SYSTEM STATUS table will appear on the active
monitor as shown in the figure.
The columns in the table indicate the states as shown in the
figure.
MON:Monitor number
CAM:Logical camera number (01 to 99)
Recorder number (R0 to R4)*
– – indicates that no camera is being
selected. 
MODE:Lists the display mode on the
monitors.
SPOT:Spot mode
Tnn:Tour Sequence mode (nn is the
tour sequence number.)
CAM:Camera Setup mode
SET:WJ-SX150A Setup mode
ALARM:Alarm Active mode
ACK:Alarm ACK mode
VLD H:Video Loss History Table 
ALM H:Alarm History Table
SYS S:System Status Table 
RECORDER:Recorder mode**
KB:Lists the system controller name
(K1 to K4) or PSD.
OPE:Lists the operator number
PRI:Lists the priority number
*R0 to R4 shows the following.
Recorder number Recorder
R0 Master recorder
R1 Slave 1 recorder
R2 Slave 2 recorder
R3 Slave 3 recorder
R4 Slave 4 recorder
** When this parameter is selected, a recorder number is
displayed in the CAM area.
4. To close the SYSTEM STATUS table, press the F2 but-
ton.
5. To exit the mode, press the MON (ESC) button.
2. Perform desired operations.
qMoving the clock display
Move the 3D joystick while holding down the F1 but-
ton. (1) will move to the desired direction.
wMoving the Camera Title Display
Move the 3D joystick while holding down the F2 but-
ton. (2) will move to the desired direction.
eMoving the Event Display
Move the 3D joystick while holding down the F3 but-
ton. (3) will move to the desired direction.
rMoving the Monitor Status*
Move the 3D joystick while holding down the F4 but-
ton. (4) will move to the desired direction.
*Monitor number, controller number and monitor
mode
●Moving All the Items
1. Press the MENU button repeatedly until OSD Position
appears on the LCD.
2. Hold down the SHIFT button. The LCD display will
become as follows.
3. Move the 3D joystick while holding down the F1 button.
(1), (2), (3), and (4) (refer to p. 11) will move to the
desired position.
■ System Status Table
The table shows the current system status.
1. Select the desired monitor. (Refer to p. 3 Monitor
Selection.)
             SYSTEM STATUS
  MON   CAM  MODE      KB    OPE     PRI
  1     01   T01       K1    12345   30
  2     99   SPOT      K2    2       2
  3     04   ALARM     K4    4       1
  4     R1   RECORDER  PC    30      1
OSD Position     003
Clock Cam Event Mon
OSD Position     003
 All 
						

							13
■ Alarm History Table
There are 100 alarm records stored in chronological order
in 10 pages of tables.
1. Select the desired monitor. (Refer to p. 3 Monitor
Selection.)
2. Press the ALM RECALL button. Alarm Recall will
appear on the LCD. The ALARM HISTORY table will
appear on the active monitor as shown in the figure.
The columns in the table indicate the status as follows:
DATE:Lists the date and time when the alarm status
changes.
ALARM:Lists the alarm number (01 - 99).
EVENT:Lists the event when the alarm status
changes.
3. Press the + button to select the next page of the history,
and press the – button to back up to the previous page.
4. To exit the mode, press the MON (ESC) or ALM
RECALL button.
■ Video Loss History Table
There are 100 video loss detection records stored in
chronological order in 10 pages of table.
1. Select the desired monitor. (Refer to p. 3 Monitor
Selection.)
2. Press the MENU button repeatedly until VLD History
appears on the LCD.
3. Press the F1 button.
The VIDEO LOSS HISTORY table will appear on the
active monitor as shown in the figure.
The columns in the table indicate the status as follows:
DATE:Lists the date and time when the video loss
status changes.
CH:Lists logical camera number, slave unit num-
ber or recorder number that is connected to
the system.
EVENT:Lists the event when the video loss status
changes.
4. To exit the mode, press the F2 button or MON (ESC)
button.
             ALARM HISTORY      1 of 2
NO  YYYY/MM/DD HH:MM:SS  ALARM  EVENT
016 2002/08/21 18:59:08  80     ALARM
015 2002/08/21 18:58:08  80     ACK
014 2002/08/21 18:57:08  80     RESET
013 2002/08/21 18:55:08  07     ALARM
012 2002/08/21 18:54:08  07     ACK
011 2002/08/21 18:53:08  07     RESET
010 2002/08/21 18:53:00  09     ALARM
009 2002/08/21 18:52:08  09     RESET
008 2002/08/21 18:51:08  06     ALARM
007 2002/08/21 18:50:08  06     ACK
          VIDEO LOSS HISTORY    1 of 2
NO  YYYY/MM/DD HH:MM:SS  CH EVENT
012 2002/08/21 18:59:08  99 VIDEO RECOVER
011 2002/08/21 18:58:08  14 VIDEO RECOVER
010 2002/08/21 18:57:08  99 VIDEO LOSS
009 2002/08/21 18:55:08  07 VIDEO LOSS
008 2002/08/21 18:54:08  R0 SW RECOVER
007 2002/08/21 18:53:08  16 VIDEO LOSS
006 2002/08/21 18:53:00  09 VIDEO LOSS
005 2002/08/21 18:52:08  R0 SW LOSS
004 2002/08/21 18:51:08  S1 SLAVE DOWN
003 2002/08/21 18:50:08  S1 SLAVE RECOVER
        
Alarm Recall
VLD History      004
  On  Off 
						

							14
MENU or WJ-SX150A Administrator Console. (Refer to
the operating instructions of matrix switcher.)
■Operation during an Alarm Mode
While an alarm mode is active, the following are available
from the system controller:
•Operating the camera with the alarm input (ACK)
•Resetting the alarm (ALM RESET/ALM ALL RESET)
•Suspending the alarm (ALM SUSPENDED)
■Operation of an Alarm-related
Camera (ACK)
You can operate the camera with the alarm input as follows:
1. Select a monitor which displays ALARM.
2. Press the ACK button.
ACK will appear on the monitor with an alarm input.
The camera with an alarm input will become operable.
3. Operate camera with the system controller.
Panning, tilting, zoom, focus, and iris are available.
When selecting another monitor, ACK will disappear
from the display. The matrix switcher system will return
to the alarm mode.
Note: This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
■Alarm Mode
When alarm (sensor) is accepted, the matrix switchers
operation mode changes to the alarm mode.  Then, the sys-
tem operates as follows:
•The camera image (alarm image) appears on the moni-
tor.
In the factory default setting, the alarm inputs 1 to 16
are associated with the same-numbered camera input
connectors. All the video output signals are sent to
Monitor 1. For example, when the alarm (sensor) con-
nected to the alarm input 1 becomes active, the camera
input connector 1’s image appears on Monitor 1.
•ALARMnn appears on the monitor.
(nn is the alarm number).
•Alarm output signals are supplied from Alarm Output 1
to 4 (#10, 11, 23 and 24) of the ALARM port (25-pin D-
sub connector) at the rear panel. Alarm Output 1 to 4 is
associated with MONITOR OUT 1 to 4. For example,
when an alarm input signal is activated on MONITOR
OUT 1, the matrix switcher supplies an alarm output
signal from Alarm Output 1.
•The alarm number and Alarm sign will appear on the
LCD. Then, Alarm sign and the alarm indicator will
blink.
There are two operation modes when more than one
alarm signal has been accepted by the matrix switcher
that is assigned to the same monitor.
• Sequence mode:An alarm operation is replaced by
another one after the dwell time ends.
• Hold mode:An initial alarm operation is continued
even after another alarm input is accepted.
Notes:
•The association of the alarm inputs with cameras and
monitors are changeable in SETUP MENU or WJ-
SX150A Administrator Console. (Refer to the operating
instructions of matrix switcher.)
•Alarm input will be automatically reset in 30 seconds.
The auto-recovery time is configurable through SETUP 
ALARM CONTROL
Mon1  Cam01     AL01
     Alarm
ALARM01ACK 
						

							15
■Resetting the Alarm Inputs
There are two alarm reset functions:
•Alarm reset (resetting the alarm inputs per monitor)
•Alarm all reset (resetting all the alarm inputs)
● Alarm Reset
1. Select a monitor which displays ALARM.
2. To reset the alarms, press the ALM RESET/ALM ALL
RESET button.
ALARMnn will disappear from the selected monitor.
When alarms have been reset from all the monitors, the
LCD display and indicators of system controllers will
work as follows for recovery.
•The LCD display will return to the state before the
alarm input.
•The alarm indicator will go out.
Note:When more than one alarm is input and they are
associated with the same monitor, they cannot be reset
one by one. 
● Alarm All Reset
1. Press the ALM RESET/ALM ALL RESET button while
holding down the SHIFT button.
2. The monitor, the indicator, and the LCD display will
change as follows:
•ALARMnn will disappear from all the monitor.
•The LED display will return to the state before the
alarm input.
•The alarm indicator will go out.
■Suspending the Alarm Inputs
Use this function when you do not want to be disturbed by
an alarm input, for example, during the setup procedures.
1. Press the ALARM/ALM SUSPEND button while holding
down the SHIFT button.
ALM SUSPENDED will appear on the monitor, and the
ALM SUSPEND indicator will light up.
2. To cancel alarm suspension, press the ALARM/ALM
SUSPEND button while holding down the SHIFT button
again.
ALM SUSPENDED will disappear from the monitor,
and the ALM SUSPEND indicator will go out.
Notes:
•An alarm continues to operate even after it is suspend-
ed.
•
If you suspend an alarm while an alarm image is dis-
played, ALM SUSPENDED will not appear on the moni-
tor. Reset the alarm, and then suspend it 
again.
ALM SUSPENDED 
						

							16
MULTIPLEXER OPERATIONS MUX
Multiplexer board WJ-SXB151 is an optional board.
It enables multiscreen display, electronic zooming, still pic-
ture and multiscreen sequence.
It also enables the operation of Digital Disk Recorder WJ-
HD100 Series or time-lapse VCR, when connected to them.
Note:Before the use, it is necessary to install the
Multiplexer board in the matrix switcher and configure
the system through SETUP MENU and WJ-SX150A
Administrator Console. (Refer to the operating instruc-
tions of matrix switcher.)
■Monitoring the Camera Picture
●Multiscreen Segment Switching
1. Select the desired monitor. (Refer to p. 3 Monitor
Selection.)
2. To select a Multiplexer, press the corresponding
numeric button.
Multiplexer board Numeric button
Master Multiplexer board 0 (You can skip pressing this button.)
Slave 1 Multiplexer board 1
Slave 2 Multiplexer board 2
Slave 3 Multiplexer board 3
Slave 4 Multiplexer board 4
3. Press the RECORDER/UNIT button. The system will
enter the recorder mode. The images from the recorder
are displayed on the active monitor in multiscreen seg-
ments.
4. Press the MULTI SCREEN button.
Every time you press the button, the multiscreen seg-
ment patterns are switched. (The following is the factory
default setting.)
4 (segments) 
→9 →16 →4
5. To return to the spot display, select the desired camera.
Note:If you activate Quad Shift in Multiplexer Mode win-
dow of WJ-SX150A Administrator Console, the multi-
screen segment patterns can be switched as follows.
4A (Page 1 of the quad – Camera 1, 2, 3, and 4) 
→4B
(Page 2 - Camera 5, 6, 7 and 8) 
→4C (Page 3 -
Camera 9, 10, 11 and 12) 
→4D (Page 4 - Camera 13,
14, 15 and 16) 
→9 (segments) →16 →4A 
(Refer to the operating instructions of matrix switcher.)
●Multiscreen Sequence
Camera images are switched automatically in a sequence
mode.
The sequence mode (QUAD, 3+1, 8+1) is configurable
through WJ-SX150A Administrator Console.
(Refer to the operating instructions of matrix switcher.)
1. Enter the recorder mode. (Refer to Step 1 to 3 of
Multiscreen Segment Switching.)
2. Press the TOUR SEQ/GROUP SEQ button.
A sequence of multiscreen pictures is displayed
according to the WJ-SX150A Administrator Consoles
configuration.
3. To cancel the sequence, press the MULTI SCREEN but-
ton.
Note:The sequence can also be cancelled by selecting
the desired camera. (In this case, you can automatically
exit the recorder mode.)
●Still Multiscreen Picture
Still pictures can also be displayed in a multiscreen.
1. Enter the recorder mode. (Refer to Step 1 to 3 of
Multiscreen Segment Switching.)
2. Press the MENU repeatedly until Mux Still appears on
the LCD.
3. Press the numeric button corresponding to the camera
number.
4. Press the F1 button.
The selected camera image will change into the still
picture.
STILL and the camera title alternately blink on the
monitor.
5. To cancel the still picture, press the numeric button cor-
responding to the desired camera number, and then
press the F1 button.
Notes:
•STILL does not appear when the still display is set to
OFF.
•When you skip Step 3 and do Step 4, all the channels
displayed in the multiscreen segments will be changed
into the still pictures.
Mux Still        052
Input Still CH 
						

							17
6. Press the EL-ZOOM button. The area surrounded by
the + signs will be zoomed up.
7. To move the zoom area, move the 3D joystick.
8. To cancel the zooming, press the EL-ZOOM button.
Note:Still picture is not available while zooming is acti-
vated. 
Note:When a WJ-HD100 Series recorder or a Panasonic
time-lapse VCR is connected to the matrix switcher,
recording status will appear on the monitor in the
recorder mode. When the normal recording is activat-
ed, REC will appear on the monitor. When the alarm
recording is activated, REC ALM will appear.
●Still Playback Spot Picture
The playback spot picture can be changed into the still pic-
ture.
Note:To use this function, you need to connect a WJ-HD100
Series recorder or time-lapse VCR to the matrix switcher.
1. Enter the recorder mode. (Refer to Step 1 to 3 of p. 16
Multiscreen Segment Switching.)
2. Press the PLAY/PAUSE button. The system will enter
the playback mode.
3. Select a camera channel by pressing a numeric button
and then pressing the CAM (SET) button. The selected
camera image will be displayed in a spot picture.
4. Press the MENU repeatedly until Mux Still appears on
the LCD.
5. Press the F1 button.
The selected camera image will change into the still
picture.
6. To cancel the still picture, press the F1 button again.
Notes:
•Still picture is not available while zooming is activat-
ed.
•Even when still picture is displayed, the playback of
the recorder/time-lapse VCR continues.
●Electronic Zooming (EL-ZOOM)
The playback spot picture can be electrically zoomed.
Note:To use this function, you need to connect a WJ-HD100
Series recorder or time-lapse VCR to the matrix switcher.
1. Enter the recorder mode. (Refer to Step 1 to 3 of p. 16
Multiscreen Segment Switching.)
2. Press the PLAY/PAUSE button. The system will enter
the playback mode.
3. Select a camera channel by pressing a numeric button
and then pressing the CAM (SET) button. The selected
camera image will be displayed in a playback spot pic-
ture.
4. Press the EL-ZOOM button.
+ signs will appear on the image.
5. To move the + signs within the picture, move the 3D
joystick.
REC
REC ALMMux Still        052
Input Still CH 
						

							18
WJ-HD500 SERIES CONTROL (TERMINAL MODE)
Matrix switcher can control the following functions of Digital
Disk Recorder WJ-HD500 Series. The following is the pro-
cedure of WJ-HD500 Series SETUP MENU.
Notes:
•The following operating procedures are for the terminal
mode. If you are using a PS·Data system controller,
refer to p. 36.
•When a Multiplexer board is installed in the matrix
switcher, you can neither connect nor control a WJ-
HD500 Series recorder. You need to remove the board
from the matrix switcher.
■Displaying WJ-HD500 Series
SETUP MENU
To display WJ-HD500 Series SETUP MENU, follow the pro-
cedure below.
1. Confirm that WJ-HD500 Series is correctly and securely
connected.
2. Select the desired monitor. (Refer to p. 3 Monitor
Selection.)
3. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.) Then, the selected monitor number, recorder
number, and /HDnnn will appear on the LCD.
4. Press the MENU button repeatedly until “System Setup”
appears on the LCD.
5. Press the F1 button.
WJ-HD500 Series SETUP MENU will appear on the
active monitor, and “
B” mark will light up beside “On”.
6. Perform the camera setting while watching the setup
menu on the monitor.
The following functions and buttons are valid in SETUP
MENU.

JogDial clockwise:
Increments a parameter.
JogDial counterclockwise:Decrements a parameter.
CAM (SET) button:Executes the selections and dis-
plays a submenu.
+ button:Increments a parameter.
– button:Decrements a parameter.
MON (ESC) button:Returns to SETUP MENU or the
previous menu. 

3D joystick upward (
D):Moves the cursor up.
3D joystick downward (C):Moves the cursor down.
3D joystick leftward (A):Moves the cursor to the left.
3D joystick rightward (B):Moves the cursor to the
right.
7. To end the setting and return to the normal view, press
the F2 button while SETUP MENU is displayed. 
B
mark will disappear from the LCD.
Mon4 Cam--        R4
              /HD500
System Setup     501
 
5On  Off
System Setup     501
  On  Off 
						

							19
■Controlling Digital Disk
Recorder WJ-HD500 Series
The following are the operating procedures of WJ-HD500
Series via system controller.
Note: Refer to the operating instructions of Digital Disk
Recorder WJ-HD500 Series for details.
●Recorder Mode
Before operating the recorder, it is necessary to enter the
recorder mode.
1. Select the desired monitor. (Refer to p. 3 Monitor
Selection.)
2. To select a recorder, press the corresponding numeric
button.
Recorder Numeric button
Master recorder 0 (You can skip pressing this button.)
Slave 1 recorder 1
Slave 2 recorder 2
Slave 3 recorder 3
Slave 4 recorder 4
3. Press the RECORDER/UNIT button. The system will
enter the recorder mode.
•The images from the recorder are displayed on the
active monitor in multiscreen segments.
•The camera number will disappear from the LCD.
•The monitor number, recorder number, and 
/ HD500 will appear on the LCD.
4. To exit the recorder mode, select the camera. (Refer to
p. 3 Camera Selection.) The monitor number and cam-
era number will appear on the LCD again.
You can also exit the recorder mode by pressing the
RECORDER/UNIT button during the recorder mode.
Note: Only one operator can enter the recorder mode. 
●Multiscreen Segment Switching
Multiscreen segment patterns are configurable through WJ-
HD500 SETUP.
(Refer to the recorder’s operating instructions.)
1. Enter the recorder mode. (Refer to Recorder Mode.)
2. Press the MULTI SCREEN button. Every time you press
the button, the multiscreen segment patterns are
switched. (The following is the factory default setting.)
4A (Page 1 of the quad 
→Camera 1, 2, 3, and 4) →4B
(Page 2 - Camera 5, 6, 7 and 8) 
→4C (Page 3 -
Camera 9, 10, 11 and 12) 
→4D (Page 4 – Camera 13,
14, 15 and 16) 
→7 (segments) →9 →10 →13 →16 →
4A
3. To return to the spot display, exit the recorder mode.
Note:Multiscreen segment patterns are not configurable
through WJ-SX150A Administrator Console.
●Normal Playback
1. Enter the recorder mode. (Refer to Recorder Mode.)
2. To start the playback, press the PLAY/PAUSE button.
The system will enter the playback mode. Then, the
most recent recorded image will be played back.
•To pause the playback, press the PAUSE button.
•To stop the playback, press the STOP button.
•
To resume the playback, press the PLAY/PAUSE button.
•To move forward/backward search during the play-
back, move the shuttle ring clockwise or counter-
clockwise.
Shuttle ring clockwise:Fast-forward playback
Shuttle ring counterclockwise:Rewind playback
Shuttle hold button:If you press this button while
rotating the shuttle ring, playback speed will be
maintained even after removing a hand from the
shuttle ring. (The LED indicator on this button
blinks during the fast playback.)
•To move forward/backward field advance during
the pause, move the JogDial clockwise or counter-
clockwise.
JogDial clockwise:Forward field advance
JogDial counterclockwise:Backward field
advance
Mon4 Cam--        R4
              /HD500 
						

							20
•To skip to the previous/next record during the play-
back, move the JogDial clockwise or counterclock-
wise. (Refer to the recorder’s operating instructions
for the description of record.) 
JogDial clockwise:Skips to the next record.
JogDial counterclockwise:Skips to the previous
record.
•To display the spot picture, press the numeric but-
ton corresponding to the desired camera number,
then press the CAM (SET) button. Then, the active
camera number will appear on the LCD.
•To resume the multiscreen display, press the MULTI
SCREEN button. 
•To change the number of multiscreen segments,
press the MULTI SCREEN button again during the
multiscreen display.
3. To stop the playback, press the STOP button. The mon-
itor display will return to the multiscreen display.
●Manual Recording
1. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.)
2. To start recording, press the REC button.
The digital disk recorder will start recording.
3. To stop the recording, hold down the REC button.
Note:Refer to WJ-HD500 Series Operating Instructions
for details and other recording modes. 
●Stopping REC ONLY Alarm
Recording
You can stop alarm recording activated by REC ONLY
setting of 430 CAMERA/440 ALARM PORT/450 SERIAL
PORT/460 MUX MOTION DET in SETUP MENU or the Alarm
Mode window in WJ-SX150A Administrator Console. (Refer
to the operating instructions of matrix switcher.) 
To stop the alarm recording, press the ALL RESET button
while holding down the SHIFT button.
●Search Playback
You can search playback images using the Record List or
Thumbnail Display. Every time you press the SEARCH/T&D
SEARCH button, the monitor display will change as follows.
Live image 
→Date-and-time entry form →Record List →
Thumbnail Display →Live image...
Then, Search Mode will appear on the LCD.
• Date-and-time Search Playback
The recorded images can be searched for through the date
and time.
1. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.)
2. Press the SEARCH/T&D SEARCH button. The date-and-
time entry form will appear on the center of the monitor.
Note:The factory default setting is the current date and
time.
3. Press the numeric buttons or +/– button to enter the
desired date and time. The cursor can be adjusted by
moving the 3D joystick rightward or leftward.
4. Press the PLAY/PAUSE button. Record List will be dis-
played and the cursor will move to the closest date and
time.
Note:To cancel the entry form, press the MON (ESC) or
EXIT button.
Search Mode   /HD500
Edit Group Alm
                 SEARCH
            YYYY/MM/DD HH:MM
            2002/05/07 19:32
Mon4 Cam01        R4
              /HD500