Panasonic System Controller Wv Cu360c Operating Instructions

63
Pan/Tilt Control (Auto/Random
Panning)
1. Select the desired monitor and camera.
2. Type 1using the numeric button, then press the PAN
button to toggle the Auto Panning function on the
selected camera On and Off.
3. Type 2using the numeric button, then press the PAN
button to toggle the Random Panning function on the
selected camera On and Off.
Note:Moving the Joystick Control will stop Auto or
Random panning.
Camera Housing Control

Wiper control
1. Select the desired monitor and camera.
2. Type...

64
System Status Display
1. Select a monitor to display the System Status Table.
2. Press the ALTbutton (indicator light on), then press the
STATUSbutton to toggle the display of the System
Status Table on the selected monitor On and Off.
ALTSTATUS 

65
For System 850
WJ-SX850 Matrix
Switcher System 

66
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS 
Front View (Template for System 850 Matrix Switcher)
qOperate indicator (OPERATE)
Is lit while power is supplied to the System Controller.
wLink indicator (LINK)
Lights up when communication is established with the
Main CPU.
eAlarm indicator (ALARM)
Lights up when an alarm condition exists. Select the
alarm number using the numeric buttons, then press
the ALARM button and the RESET button to turn off the
indicator. 
rMonitor indicator (MONITOR)
Lights up...

67
oJoystick Controller (UP/DOWN/L/R)
Used to manually operate the Pan/Tilt Head, or move
the cursor in the camera menu on the active monitor
screen.
UP: Upward
DOWN: Downward
L: Left
R: Right
!0Iris buttons (IRIS, CLOSE/OPEN)
Closes or opens the lens iris of cameras equipped with
the specified lens.
When these buttons are pressed at the same time, the
lens iris is reset to the factory default setting.
!1Focus buttons (FOCUS, NEAR/FAR)
Adjusts the lens focus of cameras equipped with the
specified lens....

68
@1Alarm Reset button (RESET)
Cancels an activated alarm.
Press this button to reset an alarm activated in the cur-
rently active unit.
Pressing this button while holding down the SHIFT but-
ton cancels all currently activated alarms at a time (ALL
RESET).
Pressing RESET in the camera menu will reset the para-
meter of a selected item or open the Special camera
menu when the cursor is positioned on SPECIAL in the
menu. Pressing it while holding down the SHIFT button
will restore all factory default...

69
#2Monitor/Monitor Lock/OSD service button
(MONITOR/OSD SERVICE), Lock indicator (LOCK)
Selects a monitor by entering a monitor number with the
numeric buttons, and then pressing this button.
To lock or unlock the currently selected monitor, press
this button while holding down the SHIFT button.  While
the LOCK indicator is lit, other operators will be barred
from accessing the monitor.
To access OSD service, press the numeric buttons
shown below, then press this button.
1:ALMS, Alarm status
2:VLDS,...

70
INSTALLATIONS (For System 850)
The installation should be made by qualified service personnel or system installers according to the following instructions.
CAUTION
System Connections
Connection Example
The connection example shows a large-scale system having a number of cameras, alarm sensors, monitors and so forth con-
nected to the System 850 Matrix Switcher.  
The System Controller WV-CU360C provides major operating functions to control the system.
Cameras Combination Cameras
Video Monitors
Time...

71
DC 9V IND ATA MODE CONTROLLER No.0987654321
DC 9V IND ATA MODE CONTROLLER No.0987654321DC 9V IND ATA MODE CONTROLLER No.0987654321
DC 9V IND ATA MODE CONTROLLER No.0987654321
PARALLELSATELLITE
MODE REDUNDANT
CPU
ETHERNET
1
CAMERA
CROSS POINT
OSD SYSTEM
CONTROLLER
DATA  6 DATA  5 DATA  4 DATA  3 DATA  2 DATA  1
PERIFERAL  INTERFACE   (
RS–
232C)(
RS–
485) SYSTEM
CONTROLLER2 3SATELLITE
STANDALONEYES NO
AC IN Central Processing Unit
125V  3.0A
SIGNAL
GND
Main CPU
DATA Port Connection
Data ports are...

72
Controller Number Setting
Set this switch always to 1 when using the System
Controller in a System 850.
Switch Setting Procedures
Set the MODE DIP switch and CONTROLLER NO. switch as
follows.
1. Remove the DC plug from the rear of the controller.
2. Set the switches as follows.
• Bit 1 should be set to OFF*.
• Bit 2 should be set to ON.
• Bit 3 should be set to OFF*.
• Bit 4 should be set to OFF*.
• Bit 5 should be set to ON* when connecting with a
System 850 in a home run (one to one) fashion.
•...