Panasonic System Controller Wv Cu360c Operating Instructions

53
For WJ-SX350 Matrix
Switcher System 

54
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS
Front View (Template for WJ-SX350)
SEQ
HISTORY
AUTO FOCUS
OPERATELOGIN ALARMBUSYPROHIBITED
AUXIRIS
CLOSE OPEN
NEAR FAR
TELE WIDE
FOCUS
ZOOM IRIS RESET
BACK
-1 CAM 
DEC+1 CAM 
INC
FWD
BACK
ALT PAUSE FUNCTION
ACK/RESET FWD
ALL RESET
RECALL
STATUSPRESET
POSIPA N
MONCAM
ESC SET
CAM
POSI
UP
LR
DOWN
MONITORCAMERA
For Matrix Switcher
WV-CU C360
CAMERA SITE CONTROL
System Controller
SET UPCAMMENU
!7
!8
!9
@0
@1
@2
@3
@4
@5
@6
@7
@8
@9
#0
#1
qwerty
u...

55
uJoystick Controller (UP/DOWN/L/R)
Used to operate the Pan/Tilt Head manually, or to move
the cursor to the desired position on the SETUP MENU
of the Matrix Switcher.
UP: Upward
DOWN: Downward
L: Left
R: Right
iIris buttons (IRIS CLOSE/OPEN)
Close or open the lens iris of cameras equipped with
the specified lens.
When these buttons are pressed at the same time, the
lens iris is reset to the factory setting.
oFocus buttons (FOCUS NEAR/FAR)
Adjust the lens focus of cameras equipped with the
specified...

56
@1@2Backward/Forward Sequence button
(SEQ BACK/FWD)
BACK:In combination with the numeric buttons, runs a
Tour or Group sequence backward on the selected
monitor.
It is also used to continue a sequence backward,
that was previously paused on that monitor by
pressing the PAUSE button.
FWD:In combination with the numeric buttons, runs a
Tour or Group sequence forward on the selected
monitor.
It is also used to continue a sequence forward, that
was previously paused on that monitor by pressing
the PAUSE...

57
INSTALLATIONS (For WJ-SX350)
The installation should be made by qualified service personnel or system installers according to the following instructions.
CAUTION
System Connections
Connection Example
The example below shows a typical system connection.
LOGIN
BUSYPROHIBITED STATUS
ALARM ALARMSEQUENCE
ACK/RESET
OPERATE
ALL RESETRECALL
CAM
MENUSET UP
PAUSEBACK
SEQFWD
SEQ
−1 CAM
DEC
DEC+1 CAM
INC
321654987
FWD
ALTSHIFTAUTO FOCUS
FUNCTIONONOFF
PRESET
POSI
CAM
POSIBACKCAM0MONSET ESCHISTORY
AUTO PANRANDM...

58
DATA Port Connection (For WJ-SX350)
Data ports are connected with RS-485 cables among devices as follows.
Note:When using cables other than those supplied, make sure to use shielded 4-wire twisted pair cable suitable for RS-485
communication.
•Internal Diagram
DIP Switch Setting (For WJ-SX350)
An 8-bit DIP switch mounted on the rear panel specifies the communication mode, etc. The default position is marked with an
asterisk *.•Basic Connection
Data Flow
–
WJ-SX350 ← WV-CU360C
WJ-SX350  ← WV-CU360C...

59
Controller Number Setting
Set this switch always to 1 when using the System
Controller with the WJ-SX350.
Switch Setting Procedures
Set the MODE DIP switch and CONTROLLER NO. switch as
follows.
1. Remove the DC plug from the rear of the controller.
2. Set the MODE switches.
Bit 1 through 3 should match the version of the WJ-
SX350 installed in your system. Open the SETUP MENU
of the WJ-SX350 and check the version shown in the
upper right corner of the menu.
For version 6.00 or later, set the...

60
CONTROLLER SETUP PROCEDURES (For WJ-SX350)
Prior to Setup
Do the following before entering the setup mode.
1. Confirm that all necessary connections and switch set-
tings are complete.
2. With the power turned off, move bit #6 of the MODE
switch on the rear to ON (administrator) position.
3. Supply power to the controller.
4. Turn on the power of cameras and other system units.
5. The LCD displays [SEtUP]. The controller is ready to
enter the setup mode.
When setup is completed, restore the switch to...

61
Setup Procedures
Set up the baud rate and parity check mode for the controller while observing the LED on the front panel.
Administrator Authorization
1. Press the CAM/SETbutton while [SEtUP] is displayed.
The [- - - - -] prompt appears.
2. Enter a password using the numeric buttons, then press
the CAM/SETbutton.
The default setting is [12345].
3. If the password entered is valid, [SPEED] appears.  If
password entry failed, the menu returns to [SEtUP].
Baud Rate
When bit 7 of the MODE switch is in...

62
OPERATING PROCEDURES (For WJ-SX350)
This section describes only some important operations
such as login, logout, and different operations from the front
panel of the WJ-SX350. 
Please refer to the manual included with the WJ-SX350 for
further information on camera selection, monitor selection
and so forth.
Login & Logout
Login
1. Type your registered operator number (a maximum of
15 digits) using the numeric buttons, then press the
CAM/SETbutton. If login has been successful, the
LOGIN indicator...