Panasonic System Controller Wv Cu360c Operating Instructions

42
@5Preset Position button (PRE - POSI)
In combination with the numeric buttons and CAM
(SET) button, moves the camera to the desired preset
position.
@6Still button (STILL)
Freezes the picture on the multiscreen monitor.
The indicator lights up when the still mode is selected.
@7Camera Set buttons (CAMERA SET ON/OFF)
Open or close the camera setup menu on the monitor
screen.
ON:Opens the selected camera setup menu on the
monitor, if applicable.
The indicator lights up when the camera setup
menu is...

43
INSTALLATIONS (For WJ-FS616/FS616C)
The installation should be made by qualified service personnel or system installers according to the following instructions.
Warning!
System Connections
Connection Example
The connection example shows cameras and an alarm sensor connected to the Video Multiplexer.  A time lapse VCR will
record pictures for later playback. The spot monitor and multiscreen monitor will display live and playback pictures while these
devices are being operated from System Controller...

44
DATA Port Connection (For Multiplexer)
Data ports are connected with RS-485 cables among devices using the Camera Communication protocol as follows.
Note:When using cables other than those supplied, make sure to use shielded 4-wire twisted pair cable suitable for RS-485
communication.
•Internal Diagram
•Basic Connection
DIP Switch Setting (For Multiplexer)
An 8-bit DIP switch mounted on the rear panel specifies the communication mode, etc. The default position is marked with an
asterisk *.
System...

45
Controller Number Setting 
Set this switch always to 1 when using the System
Controller in a system including a Multiplexer WJ-
FS616/FS616C. 
Switch Setting Procedures
1. Remove the DC plug from the rear of the controller.
2. Set the MODE switch referring to the table.
• The bit switches #1 to #3 should be set to positions that
match the version of the Multiplexer installed in the sys-
tem.
• Bit 5 opens or terminates the communication chain. The
switch should be set to OFF when the controller is...

46
SETUP PROCEDURES (For WJ-FS616/FS616C)
To display the setup menus for the WV-CU360C System Controller on the LED display, set the MODE switch and power up the
controller as described below.
Prior to Setup
Do the following before entering the setup mode.
1. Confirm that all necessary connections and switch set-
tings are complete.
2. With the power turned off, move bit #6 of the MODE
switch on the rear to ON (administrator) position.
3. Supply power to the controller.
4. Turn on the power of cameras...

47
Controller Setup 
Set up the baud rate and parity check mode for the controller while observing the LED on the front panel.
Administrator Authorization
1. Press the CAM/SET button while [SEtUP] is displayed.
The [- - - - -] prompt appears.
2. Enter a password with the numeric buttons, then press
the CAM/SET button.
The default setting is [12345].
3. If the password entered is valid, [SPEED] appears.  If
password entry failed, the menu returns to [SEtUP].
Baud Rate
In this menu, the communication...

48
4. Press the ESCbutton to go back to the previous menu.
Note:The baud rate and parity check mode of both the
WJ-FS616/FS616C and the controller must be the
same, otherwise data communications will not function.
To confirm the WJ-FS616/FS616C setup, open the COM
PORT SETUP window to check the DATA port column
parameters. Refer to Multiplexer Setup for operation.
             COM PORT SETUP
               RS-232C DATA    RS-485
    DELAY       OFF    OFF     OFF  
    BAUD RATE   9600   9600    19200...

49
OPERATING PROCEDURES (For WJ-FS616/FS616C System)
Camera Selection
One of the cameras connected to the system unit is select-
ed.
1. Enter a camera number using the numeric buttons.
The number appears on the LED display.
2. Press the CAM/SETbutton.
Note:[--] appears in the camera section of the LED dis-
play when an alarm is activated, when the multi-
screen is displayed, or when sequence mode is
run.
The following functions of the camera are controlled.
• Pan/tilt
• Focus
• Zoom
• Iris
• Defroster...

50
Note:Auxiliary control may be ignored while zooming,
focusing or panning/tilting is in operation. 
Alarm Operation
When the WV-CU360C receives an alarm signal from the
WJ-FS616/FS616C, the alarm indicator blinks. The alarm
indicator changes from blinking to steady light when the
alarm is automatically reset. The camera number appears
in the camera section of the LED display.
Alarm Reset
1. Press the ALM RESETbutton while the ALTindicator is
not lit. An activated alarm is reset and the alarm indica-...

51
Camera Setup
The cameras connected to the WJ-FS616/FS616C are set
up from the controller.
Note: Make sure that the multiplexer and the controller
are set to identical communication parameters.
General Setup
1. Select a camera pressing the numeric buttons, then
press the CAM/SET button.
2. Press the CAMERA SET ONbutton. The ON indicator
is lit while the CAMERA SET UP MENU is displayed on
the monitor.
3. Select a setup item by moving the joystick up and
down. Select a parameter by moving the joystick...