Panasonic System Controller Wv Cu360c Operating Instructions

							63
Pan/Tilt Control (Auto/Random
Panning)
1. Select the desired monitor and camera.
2. Type 1using the numeric button, then press the PAN
button to toggle the Auto Panning function on the
selected camera On and Off.
3. Type 2using the numeric button, then press the PAN
button to toggle the Random Panning function on the
selected camera On and Off.
Note:Moving the Joystick Control will stop Auto or
Random panning.
Camera Housing Control

Wiper control
1. Select the desired monitor and camera.
2. Type 3using the numeric button, then press the AUX
button to toggle the power of the Wiper on the selected
camera On and Off.
Note:To prevent premature wearing of the wiper
blades, be sure to turn off the wiper when it is not
needed or before selecting another camera for
viewing.
MONCAM
ESC SET
PA N
123
456
78
09
MONCAM
ESC SET
AUX
123
456
78
09
Defroster Control
1. Select the desired monitor and camera.
2. Type 4using the numeric button, then press the AUX
button to toggle the power of the Defroster on the
selected camera On and Off.
Auxiliary Control
The following function is available only when the WV-RC100
or WV-RC150 Receiver is included in the system.
1. Select the desired monitor and camera.
2. Type 1using the numeric button, then press the AUX
button to toggle the user Auxiliary Switch 1 of the
Receiver On and Off.
3. Type 2using the numeric button, then press the AUX
button to toggle the user Auxiliary Switch 2 of the
Receiver On and Off.
MONCAM
ESC SET
AUX
123
456
78
09
MONCAM
ESC SET
AUX
123
456
78
09 
						

							64
System Status Display
1. Select a monitor to display the System Status Table.
2. Press the ALTbutton (indicator light on), then press the
STATUSbutton to toggle the display of the System
Status Table on the selected monitor On and Off.
ALTSTATUS 
						

							65
For System 850
WJ-SX850 Matrix
Switcher System 
						

							66
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS 
Front View (Template for System 850 Matrix Switcher)
qOperate indicator (OPERATE)
Is lit while power is supplied to the System Controller.
wLink indicator (LINK)
Lights up when communication is established with the
Main CPU.
eAlarm indicator (ALARM)
Lights up when an alarm condition exists. Select the
alarm number using the numeric buttons, then press
the ALARM button and the RESET button to turn off the
indicator. 
rMonitor indicator (MONITOR)
Lights up when the monitor number is displayed on the
LED display.
tLED Display
Displays the number of monitors and cameras currently
controlled.
It also displays numeric input, error status, etc.yCamera indicator (CAMERA)
Lights up when the camera number is displayed on the
LED display.
uBusy indicator (BUSY)
Lights up when you attempt to control a monitor or cam-
era that is already used by a higher priority operator, or
when the higher priority operator selects the camera or
monitor you are currently operating.
Operations from the System Controller are disabled
until this indicator goes off.
iProhibited indicator (PROHIBITED)
This indicator lights up for 3 seconds when an attempt
is made to gain access to a function that is prohibited
by the partition.
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELE
FOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ALARM
DISARM
ACKRESET
GROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICE
CAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFT
DEF OFFDEF ON
AUX2 OFFAUX2 ON
AUX1 OFFAUX1 ON
CAM ID
OPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUS
WIPER
GEN
ALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAUTO
PA N
UP
LR
DOWN
MONITOR CAMERA
For Matrix Switcher (System 850)
WV-CU C360
CAMERA SITE CONTROL
System Controller
!9
@0
@1
@2
@3
@4
@5
@6
@7
@8
qwetryui
o!0!2!1!3!4!5!6!7!8#2#1@9#0 
						

							67
oJoystick Controller (UP/DOWN/L/R)
Used to manually operate the Pan/Tilt Head, or move
the cursor in the camera menu on the active monitor
screen.
UP: Upward
DOWN: Downward
L: Left
R: Right
!0Iris buttons (IRIS, CLOSE/OPEN)
Closes or opens the lens iris of cameras equipped with
the specified lens.
When these buttons are pressed at the same time, the
lens iris is reset to the factory default setting.
!1Focus buttons (FOCUS, NEAR/FAR)
Adjusts the lens focus of cameras equipped with the
specified lens.
When these buttons are pressed at the same time, the
lens focus is set automatically if the specified camera
with the auto focus feature is equipped.
!2Zoom buttons (ZOOM, WIDE/TELE)
Zoom the image in or out if the camera is equipped with
the specified lens.
!3Programme Preset button (PROGRAM PRESET)
In combination with the numeric buttons and CAMERA
(ENTER) button, saves a preset position of the camera
in a system equipped with the specified cameras.
To save a preset position, move the camera to the posi-
tion to be preset and select a preset number by press-
ing the numeric buttons. Hold down the PROGRAM
PRESET button, then press the CAMERA (ENTER) but-
ton.
!4Call Preset button (CALL PRESET)
In combination with the numeric buttons, moves the
pan/tilt head of the selected camera to a preset position
in a system equipped with the specified cameras. 
!5Camera/Enter button [CAMERA (ENTER)]
CAMERA:Used for camera selection. Select a camera
by pressing the corresponding numeric buttons, fol-
lowed by the CAMERA (ENTER) button.
ENTER:In combination with the numeric buttons, enter
numeric input, such as operator ID and password.
It is also used to execute the currently highlighted
selection and enter a submenu of the camera
menu.
Pressing CAMERA (ENTER) while holding down the
SHIFT button will activate the auto panning function of
the selected camera (AUTO PAN).!6Clear/Escape button [CLEAR (ESC)]
Clear:Clears numeric input from the LED display.
Escape:Escapes from the currently highlighted selec-
tion and return to the previous page of the camera
menu.
This button is also used to exit from alarm selection
mode to normal operation mode.
!7Numeric buttons (0 - 9)
Used for numeric input into the system such as the
camera and monitor number, sequence number, preset
position, etc.
Pressing the buttons shown below while holding down
the SHIFT button will select special functions.
1:Turns off the user auxiliary 1 switch of the receiver.
(AUX1 OFF)
2:Turn on the user auxiliary 1 switch of the receiver.
(AUX1 ON)
3:Turns on the housing wiper of the camera until
these buttons are released. (WIPER)
4:Turns off the user auxiliary 2 switch of the receiver.
(AUX2 OFF)
5:Turns on the user auxiliary 2 switch of the receiver.
(AUX2 ON)
7:Turns off the housing defroster of the camera. (DEF
OFF)
8:Turns on the housing defroster of the camera. (DEF
ON)
!8Shift button (SHIFT)
Pressing this button in combination with buttons to
which a special function has been assigned will acti-
vate these functions.
!9Alarm button (ALARM), Disarm indicator (DISARM)
In combination with the Numeric buttons, selects an
alarm. To select an activated alarm, press the numeric
buttons, followed by the ALARM button.
Pressing this button repeatedly enables or disables the
cameras and monitor assigned to perform the alarm
activities.
The DISARM indicator next to the button is lit while
alarm activities are disabled.
@0Alarm Acknowledge button (ACK)
Acknowledge an activated alarm. Select the alarm by
pressing the numeric buttons, followed by the ALARM
button. Select the desired alarm action number by
pressing the numeric buttons, then press the ACK but-
ton. The ACK indicator will light.
After acknowledging the alarm, press the RESET button
to reset the alarm. The ACK indicator will go off. 
						

							68
@1Alarm Reset button (RESET)
Cancels an activated alarm.
Press this button to reset an alarm activated in the cur-
rently active unit.
Pressing this button while holding down the SHIFT but-
ton cancels all currently activated alarms at a time (ALL
RESET).
Pressing RESET in the camera menu will reset the para-
meter of a selected item or open the Special camera
menu when the cursor is positioned on SPECIAL in the
menu. Pressing it while holding down the SHIFT button
will restore all factory default settings.
@2Group Preset button (GROUP PRESET)
In combination with the numeric buttons, activates a
previously programmed Group Preset function.
Pressing this button while holding down the SHIFT but-
ton will display the Operator ID number on the LED
Display for about 3 seconds (OPE ID).
@3Previous button (PREV)
Moves a Tour Sequence one step backward from the
step that was previously paused on the active monitor
by pressing the PAUSE button.
This button is also used to select a camera. Pressing
PREV while holding down the CAMERA (ENTER) button
will replace the currently selected camera with the next
lower camera number, if the active monitor is in Spot
mode.
Similarly pressing PREV while holding down the MONI-
TOR button will select the next lower monitor number.
When selecting alarms, pressing PREV while holding
down the ALARM button will select the previous alarm.
Pressing this button while holding down the SHIFT but-
ton will display the Controller ID number on the LED
Display for about 3 seconds (S-CTL ID).
@4Next button (NEXT)
Moves a Tour Sequence one step forward from the step
that was previously paused on the active monitor by
pressing the PAUSE button.
The button is also used to select a camera.  Pressing
NEXT while holding down the CAMERA (ENTER) button
will replace the currently selected camera with the next
higher camera number, if the active monitor is in Spot
mode.
Similarly pressing NEXT while holding down the MONI-
TOR button will select the next higher monitor number.
When selecting alarms, pressing NEXT while holding
down the ALARM button will select the next alarm.
@5Log Out button (LOG OUT)
In combination with the CAMERA (ENTER) button, logs
out from the system.
To prevent a log-out error, press CAMERA (ENTER)
while holding down the LOG OUT button.@6Pause button (PAUSE)
Pauses a Tour or Group Sequence that is being run on
the active monitor.
Pressing PAUSE while holding down the SHIFT button
will close the camera menu on the active monitor. The
STOP indicator will go off. (CAM MENU OFF)
@7Stop button (STOP)
Ends a Tour Sequence that is being run on the active
monitor.
To end a Group Sequence, select one of the monitors
that displays the selected sequence, then press this
button.
Pressing STOP while holding down the SHIFT button
will open the camera menu on the active monitor. The
STOP indicator will light. (CAM MENU ON)
@8Function buttons (F1, F2)
Provide access to camera attributes and operating
functions.
F1:Reserved for future use.
F2:Pressing this button will select the mode for control-
ling selected camera functions (CAM FUNC).
@9Group Sequence  button (GROUP SEQ)
In combination with the numeric buttons, runs a Group
Sequence on the assigned monitors.
Pressing GROUP SEQ will restart a forward sequence
from the next step that was previously paused by
pressing the PAUSE button.
#0Tour Sequence button (TOUR SEQ)
In combination with the numeric buttons, runs a Tour
Sequence on the active monitor.
Pressing TOUR SEQ will restart a forward sequence
from the next step that was previously paused by
pressing the PAUSE button.
#1OSD (On Screen Display) button (OSD)
Displays or hide some of the information on the screen
of the selected monitor. Press the numeric buttons
shown below, then press the OSD button.
1:Clock Display (T&D)
2:Camera Title Display (CAM ID)
3:General Status Display (GEN)
5:Monitor Status Display (MON STATUS)
6:All Displays except clock (ALL) 
						

							69
#2Monitor/Monitor Lock/OSD service button
(MONITOR/OSD SERVICE), Lock indicator (LOCK)
Selects a monitor by entering a monitor number with the
numeric buttons, and then pressing this button.
To lock or unlock the currently selected monitor, press
this button while holding down the SHIFT button.  While
the LOCK indicator is lit, other operators will be barred
from accessing the monitor.
To access OSD service, press the numeric buttons
shown below, then press this button.
1:ALMS, Alarm status
2:VLDS, Video loss detection status
3:SYS S, System status
4:ALM H, Alarm history
5:VLDH, Video loss detection history 
						

							70
INSTALLATIONS (For System 850)
The installation should be made by qualified service personnel or system installers according to the following instructions.
CAUTION
System Connections
Connection Example
The connection example shows a large-scale system having a number of cameras, alarm sensors, monitors and so forth con-
nected to the System 850 Matrix Switcher.  
The System Controller WV-CU360C provides major operating functions to control the system.
Cameras Combination Cameras
Video Monitors
Time Lapse VCRs
Sensors
System 850
Matrix Switcher
System Controllers
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ARARMDISARMACKRESETGROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICECAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFTDEF OFFDEF ONAUX2 OFFAUX2 ONAUX1 OFFAUX1 ONCAM IDOPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUSWIPERGENALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAUTO
PA N
UP
LR
DOWN
MONITOR CAMERAFor Matrix Switcher (System 850)WV-CU C360CAMERA SITE CONTROLSystem Controller
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ARARMDISARMACKRESETGROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICECAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFTDEF OFFDEF ONAUX2 OFFAUX2 ONAUX1 OFFAUX1 ONCAM IDOPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUSWIPERGENALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAUTO
PA N
UP
LR
DOWN
MONITOR CAMERAFor Matrix Switcher (System 850)WV-CU C360CAMERA SITE CONTROLSystem Controller
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ARARMDISARMACKRESETGROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICECAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFTDEF OFFDEF ONAUX2 OFFAUX2 ONAUX1 OFFAUX1 ONCAM IDOPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUSWIPERGENALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAUTO
PA N
UP
LR
DOWN
MONITOR CAMERAFor Matrix Switcher (System 850)WV-CU C360CAMERA SITE CONTROLSystem Controller
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ARARMDISARMACKRESETGROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICECAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFTDEF OFFDEF ONAUX2 OFFAUX2 ONAUX1 OFFAUX1 ONCAM IDOPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUSWIPERGENALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAUTO
PA N
UP
LR
DOWN
MONITOR CAMERAFor Matrix Switcher (System 850)WV-CU C360CAMERA SITE CONTROLSystem Controller
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ARARMDISARMACKRESETGROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICECAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFTDEF OFFDEF ONAUX2 OFFAUX2 ONAUX1 OFFAUX1 ONCAM IDOPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUSWIPERGENALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAU TO
PA N
UP
LR
DOWN
MONITOR CAMERAFor Matrix Switcher (System 850)WV-CU C360CAMERA SITE CONTROLSystem Controller
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ARARMDISARMACKRESETGROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICECAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFTDEF OFFDEF ONAUX2 OFFAUX2 ONAUX1 OFFAUX1 ONCAM IDOPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUSWIPERGENALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAU TO
PA N
UP
LR
DOWN
MONITOR CAMERAFor Matrix Switcher (System 850)WV-CU C360CAMERA SITE CONTROLSystem Controller
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ARARMDISARMACKRESETGROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICECAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFTDEF OFFDEF ONAUX2 OFFAUX2 ONAUX1 OFFAUX1 ONCAM IDOPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUSWIPERGENALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAUTO
PA N
UP
LR
DOWN
MONITOR CAMERAFor Matrix Switcher (System 850)WV-CU C360CAMERA SITE CONTROLSystem Controller
AUTO FOCUS
OPERATE LINK ALARMBUSYPROHIBITED
IRIS
CLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM IRIS RESET
PREV
SEQ
SEQTOURGROUP
ARARMDISARMACKRESETGROUP PRESET NEXT
LOG OUT PAUSE STOP
F1
F2 MONITOR
CAM FUNC LOCK
OSD SERVICECAMERA
(ENTER) CLEAR
(ESC)CALL
PRESET
PROGRAM
PRESET
SHIFTDEF OFFDEF ONAUX2 OFFAUX2 ONAUX1 OFFAUX1 ONCAM IDOPE IDS-CTL ID
OSD
CAM MENU OFFCAM MENU ON
ALL RESET
MDN STATUSWIPERGENALL
EXIT BLK VLD H ALM HVLD S SYS S ALM SAUTO
PA N
UP
LR
DOWN
MONITOR CAMERAFor Matrix Switcher (System 850)WV-CU C360CAMERA SITE CONTROLSystem Controller
System Controller WU-CU 850 
						

							71
DC 9V IND ATA MODE CONTROLLER No.0987654321
DC 9V IND ATA MODE CONTROLLER No.0987654321DC 9V IND ATA MODE CONTROLLER No.0987654321
DC 9V IND ATA MODE CONTROLLER No.0987654321
PARALLELSATELLITE
MODE REDUNDANT
CPU
ETHERNET
1
CAMERA
CROSS POINT
OSD SYSTEM
CONTROLLER
DATA  6 DATA  5 DATA  4 DATA  3 DATA  2 DATA  1
PERIFERAL  INTERFACE   (
RS–
232C)(
RS–
485) SYSTEM
CONTROLLER2 3SATELLITE
STANDALONEYES NO
AC IN Central Processing Unit
125V  3.0A
SIGNAL
GND
Main CPU
DATA Port Connection
Data ports are connected with RS-485 cables among devices using Camera Communication protocol as follows.
Note:When using cables other than those supplied, make sure to use shielded 4-wire twisted pair cable suitable for RS-485
communication.
•Internal Diagram
•Basic Connection
Data Flow
–
Main CPU ← WV-CU360C
Main CPU  ← WV-CU360C
Main CPU  → WV-CU360C
Main CPU  → WV-CU360C
–
1
61
6
No.No.
11
22
33
44
55
66
Name
GND
TX(B)
TX(A)
RX(B)
RX(A)
GND
Controller endTX (B) 
TX (A)
RX (A)
RX (B) 
						

							72
Controller Number Setting
Set this switch always to 1 when using the System
Controller in a System 850.
Switch Setting Procedures
Set the MODE DIP switch and CONTROLLER NO. switch as
follows.
1. Remove the DC plug from the rear of the controller.
2. Set the switches as follows.
• Bit 1 should be set to OFF*.
• Bit 2 should be set to ON.
• Bit 3 should be set to OFF*.
• Bit 4 should be set to OFF*.
• Bit 5 should be set to ON* when connecting with a
System 850 in a home run (one to one) fashion.
• Bit 6 should be set to OFF* (Operator) normally, or ON
(Administrator) when setting up the controller.
• Bit 7 should be set to ON. The baud rate is selected in
the controller setup.
• Bit 8 should be set to OFF* normally.
3. Connect the DC plug to the controller.
SW position
OFF
See below
See below
See below
Not used
On*
Administrator
Set up from CU360
3 times Function
ON
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8System ID
System ID
System ID
Reserved
Line termination
Operation mode
Baud Rate Selection
Repeat Transmissions*
*
*
*
Off
Operator*
Auto-selection*
1 time*
MODE
123456 78
OFF
ON
0987654321
CONTROLLER No.
DIP Switch Setting
An 8-bit DIP switch mounted on the rear panel specifies communication mode, etc. The default position is marked with an
asterisk *.
DC 9V IND ATA MODE CONTROLLER No.0987654321