Panasonic System Controller Wv Cu360c Operating Instructions

							21
Camera Cleaning
This menu is for specifying the order in which combination
cameras connected to the system are cleaned.
The camera cleaning function causes cleaning of the built-
in slip rings that conduct electric signals while moving the
pan/tilt head.  All combination cameras connected to the
system are cleaned in the order specified here.  Picture
viewing is disabled during the cleaning process.
1. Display [CLEAn] and press the CAM/SET button. The
LED displays [no-01].
2. Use the numeric buttons to enter the number of the
camera where cleaning is to start.
The default setting is no-01.
Available camera numbers:01-199
3. Press the CAM/SET button to start cleaning.
Two animated digits appear in the left part of the LCD
while the digits at right display the number of the cam-
era being cleaned.
When cleaning is finished, the number of the last cam-
era cleaned is displayed without animation.
4. Press the ESC button to go back to the previous menu.
Unit Connection Test
This menu is for specifying the order in which data commu-
nication between system units is tested prior to operating
the system as a whole.
1. Display [UtESt] and press the CAM/SET button. The
LED displays [01-on] or [01-oF].
2. Enter the 2-digit unit number you wish to start with.
3. Press the CAM/SET button to start the test.
The digits in the left part of the LCD display the unit
number under test while 2 animated digits appear at
right.
To stop the test in progress, press the CAM/SET button.
When testing is finished, the number of the last unit test-
ed is displayed without animation.
4. Press the CAM/SET button. Enter a 2-digit number(e.g.,
01), then press the CAM/SET button.
You can now confirm the test results of a specific unit.
When Off is displayed, check connections, switch set-
tings, etc., of the system unit. 
01-on:On, unit 01 is connected.
01-oF:Off, unit 01 is disconnected.
5. Press the ESC button to go back to the previous menu. 
						

							22
Basic Operating Flow
The operation starts with a log-in procedure. It proceeds to system unit selection, monitor selection and camera selection.
Alarm operations for the system such as alarm reset, suspension may be implemented. The operation ends with a log-out pro-
cedure.
OPERATING PROCEDURES (PS•Data)
LOG IN
SYSTEM UNIT SELECTION
MONITOR SELECTION
LOG OUT
SYSTEM 
OPERATION
• Alarm Reset
• Alarm Suspend
• Alarm Suspend
Cancel
SYSTEM UNIT
OPERATION
• System Unit Setup
• System Function
• Alarm Recall
CAMERA
OPERATION
• Camera Setup
• Pan/Tilt (Slow)
• Iris/Focus/Zoom
• Preset Position
• Home Position
• Switching of
Color/Black &
White
• Auto Panning
• Camera Patrol
• Camera Patrol
Stop
• Camera Patrol
Learn
• Camera Function
• Wiper/Defroster
• Auxiliary Control
1/2
CAMERA 
SELECTION
d
d
d
MONITOR
OPERATION
• Switching of VCR
and CAM
• Multiscreen
Selection
• Still
• Electronic Zoom
• Sequence
• Sequence Pause 
						

							23
Login/Logout
Log In
Right after powering up, the controller will be operable with-
out password entry, provided user password certification is
set to Off in the setup menu.
When set to On, you will be prompted to enter your regis-
tered password.  The default password is “12345”, but you
need to remember the password assigned to you by your
system administrator.
1. Insert the DC plug into the DC 9 V IN jack and connect
the AC adapter to an AC outlet.
2. The controller number, software versions and [LogIn]
appear in that order on the LED display.
The LOGIN indicator lights up.  The controller is now
operable unless password certification is activated. If it
is not activated, proceed as follows.
3. Press the CAM/SET button.
4. Enter a 5-digit user password with the numeric buttons.
The initial factory setting is [12345].
5. Press the CAM/SET button.
6. If password entry for user authorization has been suc-
cessful, the LOGIN indicator lights up.
The unit assigned to the UNIT A/UNIT button as number
1 is selected automatically.
If password entry has failed, [Error] appears on the dis-
play. The display returns to [LogIn].
Log Out
1. Press the MON/ESC and CAM/SET buttons for about 2
seconds simultaneously.
2. [LogIn] appears on the display and the LOGIN indicator
goes off.
3. Disconnect the DC plug from the controller, and remove
the AC adapter from the AC outlet.
Note:If the power is not turned off after logout, the
alarm indicator and alarm suspend indicator will
display the same status as in normal operation.
SET
SET
ESC
Unauthorized
OPERATELOGIN ALARM
SET
Ready for user password entry
Authorized
User password entryBlink
The unit that is assigned to the UNIT A/UNIT 
button as number 1 is selected automatically.
Lights after authorization
   Goes off after logout
Certification
off 
						

							24
Selecting with UNIT A/UNIT B Button
The unit numbers (01-99) of some frequently used units can
be assigned to numeric buttons 1-9 in the setup.  Units can
be divided in two groups, one assigned to the UNIT A and
the other to the UNIT B button.  A frequently used system
unit can be easily selected by pressing one numeric button
and then the UNIT A or UNIT B button.
1. Enter a single digit number (1-9). 
Omit this step when you wish to select unit number “1”,
as this unit is selected by default.
2. Press the UNIT Aor UNIT Bbutton while the SHIFT
indicator is off.
The selected unit address appears in the unit section of
the LED display.
The selected camera number appears in the camera
section of the LED display.
System Unit Selection
Connected system units can be selected either by their unit
number (01-99) or by a single-digit number (1-9) assigned
to the UNIT A or UNIT B button.
Selecting with Unit Number
1. Enter a unit number (01-99) with the numeric buttons.
2. Press the SHIFTbutton to turn the shift indicator on,
then press the UNIT A/UNITbutton.
The selected unit number appears in the unit section of
the LED display.
The selected camera number appears in the camera
section of the LED display.
Notes:
• To confirm the selected unit number when the moni-
tor number appears in the unit section of the LED
display, take procedure 2 or press MON/ESC but-
ton .
• If no unit is connected, [Err] appears a few seconds
after unit selection.  In such a case, confirm the unit
address and repeat the above procedure.
• If the unit address of a system unit is unknown, con-
sult your system administrator.
• When multiple system units such as Data Multiplex
Unit are connected to the System Controller and the
UNIT A or UNIT B button is pressed, the camera
number on the controllers LED display will not
agree with the camera picture on the monitor.
In this case, select the monitor and camera as
described on the next page.
MONCAM
LOGOUT
ESC SET
SHIFT
UNIT A
then
UNIT
MONCAM
LOGOUT
ESC SET
UNIT A
or
UNIT
UNIT B 
						

							25
Monitor Selection
A monitor is selected when multiple monitors are connected
to a system unit (e.g., a Video Multiplexer) to control such
functions as multiscreen display and electronic zoom.
1. Select the system unit connected to the monitor you
wish to control. 
2. Enter a monitor number using the numeric buttons.
3. Press the MON/ESCbutton.
The selected monitor number appears in the monitor
section of the LED display.
The selected camera number appears in the camera
section of the LED display.
The monitor is now ready for control from the system
controller.
Notes:
• To confirm the selected monitor number, simply
take procedure 3 when the unit address appears in
the monitor section of the LED display.
• Each time the MON/ESC button is pressed, the unit
number and monitor number are displayed alter-
nately on the LED.
• The setting is invalid if the unit in which the monitor
number has been set is not programmed. 
• In the above case, repeat the same procedure after
confirming the monitor number. If you do not know
the monitor number, consult the administrator.
• When [--] appears in the monitor section of the LED
display, the selected system unit is not compatible
with the monitor selection.
• For further information, refer to the Operating Inst-
ructions for the system unit concerned.
MONCAM
LOGOUT
ESC SET
MON
ESC
Camera Selection
One of the cameras connected to the system unit is select-
ed.
1. Select a system unit connected to the camera whose
picture you wish to view.
2. Enter a camera number using the numeric buttons.
The entered camera number appears on the LED dis-
play.
3. Press the CAM/SETbutton.
Note:[--] appears in the camera section of the LED dis-
play when an alarm is activated, when the multi-
screen is displayed, or when a sequence mode is
running.
The following functions are available after selecting a cam-
era.
• Pan/tilt
• Focus
• Zoom
• Iris
• Defroster ON/OFF (camera housing)
• Wiper ON/OFF (camera housing)
• Preset Position (Combination Camera)
• Home position (Combination Camera)
• Switching between color and B/W picture 
(Combination Camera)
• Auto pan (Combination Camera)
• Patrol Learn function (Combination Camera)
• Camera functions (Combination Camera)
The selected camera number can be incremented or
decremented by one if the system unit is equipped with the
camera switching feature.
1. Press the SHIFTbutton to turn the shift indicator on.
2. Press the EL-ZOOM/+button to increment or the
STILL/–button to decrement the camera number.
MON CAM
LOGOUTESC SET 
						

							26
2. Press the ZOOM TELEbutton to optically bring the
object closer, or press the ZOOM WIDEbutton to opti-
cally widen the scene.
3. Press the IRIS CLOSEbutton to close the iris, or the
IRIS OPEN button to open the iris.
If the IRIS CLOSEand IRIS OPENbuttons are pressed
simultaneously, the iris is reset to the default.
Home/Preset Position 
The camera moves to the preset position or back to the
home position, and the picture of the camera in that posi-
tion appears on the monitor.
1. Press the HOME/PRESETbutton to move the camera
back to the home position.
2. Select a preset position number using the numeric but-
tons, then press the HOME/PRESETbutton to move the
camera to the position.
Camera Control
Cameras and their peripherals are controlled from the WV-
CU360C as follows. Some of the descriptions may not be
applicable if they refer to devices not equipped in your sys-
tem.
The operating procedures on the following pages assume
that you have selected a system unit and a monitor.
Pan/Tilt Control
Proceed as follows to control a combination camera or an
ordinary camera mounted on a pan/tilt head.
1. Move the pan/tilt head in the desired direction with the
joystick controller.
2. To slowly move the pan/tilt head, move the joystick
while holding down the SLOWbutton.
Lens Control
This allows you to control a motorized lens.
1. Press the FOCUS NEARor FOCUS FARbutton to
adjust the lens focus while watching the monitor.
If you are using a camera with an auto focus feature,
the lens focus can be automatically adjusted by press-
ing the FOCUS NEARand FOCUS FARbuttons simul-
taneously.
IRIS
CLOSE OPEN
IRIS RESET
WIDE TELE
ZOOM
NEAR FAR
FOCUS
AUTO FOCUS
SEQ PAUSE
SLOW
Joystick
HOME/PRESET
PROGRAM
PRESET
MONCAM
LOGOUT
ESC SET
HOME/PRESET
PROGRAM
PRESET 
						

							27
Combination Camera Shortcuts
The shortcuts listed below are available for controlling combination cameras. For more details, refer to the Operating
Instructions included with the camera.
Selecting a PRESET position From #1 to #64
#1 [1] + [CAM FUNC]
#10 [1] + [0] + [CAM FUNC]
#64 [6] + [4] + [CAM FUNC]
AUTO PAN
ON [6] + [5] + [CAM FUNC]
OFF [6] + [6] + [CAM FUNC]
Speed Up [6] + [7] + [CAM FUNC]
Speed Down [6] + [8] + [CAM FUNC]
Setting Start Point [6] + [9] + [CAM FUNC]
Setting End Point [7] + [0] + [CAM FUNC]
Setting PAN Reverse [7] + [4] + [CAM FUNC]
AUTO MODE
MODE Off [7] + [1] + [CAM FUNC]
SEQ On [7] + [2] + [CAM FUNC]
SORT On [7] + [3] + [CAM FUNC]
ENDLESS PAN
On [7] + [6] + [CAM FUNC]
Off [7] + [7] + [CAM FUNC]
DIGITAL FLIP 
On [7] + [8] + [CAM FUNC]
Off [7] + [9] + [CAM FUNC]
PROP. PAN/TILT
On [8] + [0] + [CAM FUNC]
Off [8] + [1] + [CAM FUNC]
SUPER-D2
On [8] + [4] + [CAM FUNC]
Off [8] + [5] + [CAM FUNC]
AUTO FOCUS
STOP AF On* [8] + [6] + [CAM FUNC]
STOP AF Off* [8] + [7] + [CAM FUNC]
AF On (Activate) [8] + [8] + [CAM FUNC]
HOME POSITION
Move to HOME [8] + [9] + [CAM FUNC]
B/W or C/L 
B/W On* [9] + [0] + [CAM FUNC]
B/W Off* [9] + [1] + [CAM FUNC]
B/W AUTO* [9] + [2] + [CAM FUNC]
CAMERA ID
On [9] + [3] + [CAM FUNC]
Off [9] + [4] + [CAM FUNC]
AREA TITLE
NESW On [9] + [5] + [CAM FUNC]
USER On [9] + [6] + [CAM FUNC]
TITLE Off [9] + [7] + [CAM FUNC]EL-ZOOM
On [9] + [8] + [CAM FUNC]
Off [9] + [9] + [CAM FUNC]
RESTART
Begin [1] + [0] + [0] + [CAM FUNC]
Memorize PRESET From #1 to #64**
Position #1 [1] + [0] + [1] + [CAM FUNC]
Position #10 [1] + [1] + [0] + [CAM FUNC]
Position #64 [1] + [6] + [4] + [CAM FUNC]
PATROL
PLAY [1] + [6] + [5] + [CAM FUNC]
STOP [1] + [6] + [6] + [CAM FUNC]
LEARN(Start) [1] + [6] + [7] + [CAM FUNC]
IRIS
Open [1] + [6] + [9] + [CAM FUNC]
Close [1] + [7] + [0] + [CAM FUNC]
EL-SHUTTER
On [1] + [7] + [1] + [CAM FUNC]
Off [1] + [7] + [2] + [CAM FUNC]
Speed Up [1] + [7] + [3] + [CAM FUNC]
Speed Down [1] + [7] + [4] + [CAM FUNC]
AGC
On [1] + [7] + [5] + [CAM FUNC]
Off [1] + [7] + [6] + [CAM FUNC]
SENS UP
On [1] + [7] + [7] + [CAM FUNC]
Off [1] + [7] + [8] + [CAM FUNC]
Up [1] + [7] + [9] + [CAM FUNC]
Down [1] + [8] + [0] + [CAM FUNC]
SENS UP AUTOOn [1] + [8] + [1] + [CAM FUNC]
Off [1] + [8] + [2] + [CAM FUNC]
Up [1] + [8] + [3] + [CAM FUNC]
Down [1] + [8] + [4] + [CAM FUNC]
LL SYNC phase
INC [1] + [8] + [5] + [CAM FUNC]
DEC [1] + [8] + [6] + [CAM FUNC]
PAN
180°turn [1] + [8] + [7] + [CAM FUNC]
CLEANING
On [1] + [8] + [8] + [CAM FUNC]
Off [1] + [8] + [9] + [CAM FUNC]
BW SW AUTO
30 sec. [1] + [9] + [0] + [CAM FUNC]
60 sec. [1] + [9] + [1] + [CAM FUNC]
300 sec. [1] + [9] + [2] + [CAM FUNC]
600 sec. [1] + [9] + [3] + [CAM FUNC]
Function Key Function Key
Notes: 
• Shortcut operations marked with * will change parameter settings only. Actual operation takes place
when the conditions for the changed settings are met.
• When entering shortcuts marked with **, “NO REGS. ; FLIP ON” may appear on the monitor. Re-enter
the shortcut.
• Shortcuts may be ignored while PAN/TILT, ZOOM or FOCUS is in operation.
• PATROL LEARN saves only [1] through [6]+[4], [1]+[6]+[9] and [1]+[7]+[0] in the memory.
• PATROL PLAY stops when a shortcut other than [1]+[6]+[9] or [1]+[7]+[0] is entered. 
						

							28
Housing/AUX Control
When your system includes a camera housing, the
defroster and wiper equipped in it are controlled. When a
Receiver is installed in the system, an auxiliary device con-
nected to it such as a buzzer or lamp will be also con-
trolled.
8Defroster
Press the DEF/AUX 2button to enable or disable defroster
operation for the selected camera. The DEF/AUX 2indica-
tor next to the button is lit while it is in operation.
8Wiper
Press the WIPER/AUX 1button to enable or disable wiper
operation for the selected camera. The WIPER/AUX 1indi-
cator next to the button is lit while it is in operation.
Note:To prevent early wiper wear, be sure to turn off the
wiper whenever it is not needed, or before selecting
another camera for viewing.
8Auxiliary 1/2
1. Press the SHIFTbutton to turn the SHIFT indicator on.
2. Press the WIPER/AUX 1or DEF/AUX 2button to
enable or disable the auxiliary function for the selected
camera. The respective indicator next to the button is lit
while it is in operation.
Note:Auxiliary control may be ignored while zooming,
focusing or panning/tilting is in operation. 
Data Multiplex Unit Control
When more than one Data Multiplex Unit are connected
with the controller as shown in System Connection Example
2 on page 14, you can select a camera directly with the
camera number, without typing a system unit address. 
Setting
Camera numbers are specified by the UNIT switch or in the
setup menu for the WJ-MP204C. 
For further details, refer to the manual included with the
Data Multiplex Unit.
When more than one controller is connected in the system,
remember settings are needed for the MODE DIP switch
and CONTROLLER NO. switch of the controllers as
described on page 16. 
Camera Selection
1. Press a camera number using the numeric buttons.
2. Press the CAM/SETbutton.
WIPER
AUX 1
DEF
AUX 2
DEF
WIPER
AUX 1
AUX 2SHIFT
Unit Address  Camera Number of WJ-MP204C
1 1, 2, 3, 4
2 5, 6, 7, 8
3 9, 10, 11, 12
4 13, 14, 15, 16
MONCAM
LOGOUT
ESC SET
CAM
SET 
						

							29
Video Multiplexer Control
Some of the major functions equipped in a Video
Multiplexer are remotely controlled from the System
Controller. For more information, refer to the manual includ-
ed with the Video Multiplexer. 
The operating procedures on the following pages assume
that you have selected a system unit and a monitor.
Multiscreen Selection
1. Press the MULTISCREEN SELECTbutton. The select-
ed multiscreen monitor displays a split screen.
2. Press the button repeatedly to select the number of
segments you wish the multiscreen to display.  Each
time the button is pressed, the number changes as fol-
lows depending on the number of inputs (16 or 9).
16-input:4 →9 →16 →4 screen segments
9-input:4 →9 →4 screen segments
Still Picture
There are two ways of displaying still pictures on the multi-
screen monitor.
8Specific camera still
1. Select a camera number using the numeric buttons,
then press the STILL/–button. The selected camera
picture freezes on the multiscreen while the STILL/–
indicator is lit.
2. Press the STILL/–button to cancel still display mode.8All cameras still
1. Enter 0 with the numeric buttons, then press the
STILL/–button.  All camera pictures freeze on the mul-
tiscreen while the STILL/–indicator is lit.
2. Press the STILL/–button to cancel the still display
mode.
Electronic Zoom
A picture displayed on the monitor can be electronically
zoomed in, and the enlarged area in the picture can be
moved using the joystick.
1. Press the EL-ZOOM/+button. The EL-ZOOM/+indica-
tor is lit, and a plus mark [+] appears in the center of
the monitor screen.
2. Move the [+] mark into the zoom area moving the joy-
stick.
3. Press the EL-ZOOM/+button again to zoom.
You can move the enlarged area on the monitor using
the joystick.
4. Press the EL-ZOOM/+button to cancel the zoom mode.
The EL-ZOOM/+indicator goes off. 
MULTI SCREEN SELECT1
2
34
Example of Quad Picture
STILL
–
STILL
–
0
EL-ZOOM
+
UP
LR
DOWN 
						

							30
Viewing Playback
VCR playback pictures are displayed on the selected spot
or multiscreen monitor.
1. With the connected VCR in playback mode, press the
VCR/CAMbutton to turn on the VCR indicator.
Playback pictures are displayed on the selected moni-
tor.
2. Press the VCR/CAMbutton again to cancel viewing
playback. The VCR indicator goes off.
Note:This function is automatic when PLAYBACK
AUTO is set to ON in the Video Multiplexer setup
and the playback signal is supplied to the Video
Multiplexer. Set PLAYBACK AUTO to OFF in the
setup when you wish manual operations as
described above.
Sequence Control
A preset sequence is displayed on the selected spot or
multiscreen monitor. The paused picture can be moved by
one step to the previous or next frame.
1. Press the SEQUENCEbutton. The sequence is dis-
played on the monitor while the SEQUENCEindicator is
lit.
2. To pause the sequence, press the SEQ PAUSEbutton.
3. To move the sequence one step forward, press the EL-
ZOOM/+button.4. To move the sequence one step back, press the
STILL/–button.
5. To cancel the sequence pause, press the SEQ PAUSE
button again.
VCR   CAM
SEQUENCE
PATROL
STOP
SEQ PAUSE
SLOW
SEQ PAUSE
SLOW
EL-ZOOM
+
STILL
–