Panasonic Pv Dv852 Operating Instructions Manual

							31
Index Search Functions
To facilitate searching of desired scene, this Palmcorder automatically 
records index signals during recording, as explained in the following.
PhotoShot Index Signal
These signals are automatically recorded whenever still pictures are taken in 
PhotoShot Mode (l21).
When recording still pictures using the Continuous PhotoShot Mode (l21), 
the index signal is not recorded.
Scene Index Signal
Scene Index Signals are automatically recorded when you start recording 
after inserting a Cassette.
However, if the Palmcorder is switched from the VCR Mode to Camera Mode 
or if the date and time is set before the start of recording, the index signal is 
not recorded.
≥If [INDEX] of [RECORDING SETUP] Sub-Menu on the 
[CAMERA FUNCTIONS] Main-Menu is set to [2HOUR], an index signal is 
recorded when Recording is restarted after a lapse of 2 hours or longer. If it 
is set to [DAY], an index signal is recorded when recording is restarted after 
the date has changed since the last recording. (While the index signal is 
recorded, the [INDEX] Indication 
1 flashes for a few seconds.)
ªPhotoShot Index Search
1
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[INDEX] >> [PHOTO].
2Press the [9] Button 1 or the [:] Button 2 on the 
Remote Controller.
≥With each press of the corresponding button, still pictures recorded in 
PhotoShot Mode are searched.
≥After Pictures with Sounds are played back for 4 seconds, the Palmcorder 
switches to the Still Playback Mode.
ªScene Index Search
1
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[INDEX] >> [SCENE].
2Press the  [9] Button 1 or the [:] Button 2 on the 
Remote Controller.
≥When the corresponding Button is pressed once, the [S 1] Indication 2 
appears, and searching of the subsequent scene marked with an index 
signal starts. Each time the button is pressed after the start of Scene Index 
Search, the indication changes from [S 2] to [S 9], and the beginning of the 
scene corresponding to the selected number will be searched. After 
reaching the desired scene, playback starts automatically.
≥Up to 9 scene numbers can be selected.
Top Scan
If the [9] Button or the [:] Button is pressed for more than 2 seconds, 
the Palmcorder will scan for scenes (or PhotoShots) and playback the first 
few seconds of each. (To cancel, press the [
1] Button 3 or the [∫] Button 
4.)
≥For other notes, see page 61.
2 1
INDEX
S 1
2
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VA R .
SEARCHP.B.
ZOOM
3
4
1 2
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGSEARCHAUTOMANUAL
1

						

							32
Playback Zoom Function
A part of the image can be enlarged up to 10 times during playback.
1During playback, press the Playback Zoom Button 
[P.B. ZOOM] on the Remote Controller.
≥The center of the image is enlarged to approximately double the size.
Changing the Zoom Magnification
2Change the magnification by pressing the [W] or [T] Button 
on the Remote Controller.
≥You can increase the magnification up to 10a.
Changing the enlarged area of an image
3Press the Arrow Button (π, ∑, ∏, ∫) on the Remote 
controller that points to the area you want to enlarge.
Cancelling the Playback Zoom Function
Press the [P.B. ZOOM] Button on the Remote Controller.
≥For other notes, see page 61.
~~~~~~~~~~~~~~~~~~~~~~~~
Playback Digital Effect Functions
During playback, special Digital Effects can be added to the Recording. The 
digital effects that may be applied in the process of recording (except Picture 
in Picture Mode) will be the same as these added effects.
1Press the [1] Button.
2Press the [SELECT] Button of the Remote Controller and 
select desired Digital Effect .
≥When the [SELECT] Button is pressed repeatedly, the Digital Effect 
selection changes.
MULTI  )WIPE )MIX )STROBE  )NEGA )SEPIA )MONO 
)TRAIL ) SOLARI  )MOSAIC ) MIRROR
≥The same setting can also be set using the [DIGITAL EFFECT] on the 
[VCR FUNCTIONS] Main-Menu.
Suspending Playback Digital Effect temporarily
Press the [OFF/ON] Button 1 to clear or restart the digital effect. When the 
Digital effect is paused temporarily, the selected effect’s indication flashes.
Cancelling the Digital Effect
Press the [SELECT] Button on the Remote Controller repeatedly until the 
Digital Effect Indication is cleared.
≥For other notes, see page 61.
~~~~~~~~~~~~~~~~~~~~~~~~ªPlayback with Wipe Mode and Mix Mode
1
Press the [1] Button.
2Press the [SELECT] Button of the Remote Controller and 
select [WIPE] or [MIX].
3Press the [STORE] Button at the moment you want to save 
as a still picture.
≥The last scene is stored in memory. The [WIPE] or [MIX] Indication 
changes to [B] or [C].
4Press the [OFF/ON] Button in the scene in which you want to 
use the Wipe or Mix effect.
≥The scene changes as a result of the Wipe or Mix effect.
≥The Wipe Function and Mix Function can be used only from the Remote 
Controller during playback.
≥If the [OFF/ON] Button is pressed while Wipe Function or Mix is used, the 
effect will stop temporarily at that point. Pressing the [OFF/ON] Button again 
will bring back the effect.
2
1
3
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
ZOOM  5t
1
3 2
4
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
WIPE
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
1
2
1

						

							33
1
2
3
2
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S E
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP. B .
ZOOM
4MULTI/P-IN-P
1,13
4
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGSEARCHAUTOMANUAL
1, 2
ªPlaying Back with Multi-Picture Mode 
Strobe Multi-Picture Mode [STROBE] 1:
You can capture 9 consecutive still pictures from playback images.
Manual Multi-Picture Mode [MANUAL] 
2:
Selecting a desired still picture one at a time, you can capture 9 still pictures.
Index Multi-Picture Mode ([PHOTO], [SCENE]) 
3:
You can capture 9 screens of pictures to which index signals are attached.
After setting [VCR FUNCTIONS] >> [DIGITAL EFFECT] >> 
[EFFECT SELECT] >> [MULTI]...
1Set [MULTI-PICTURES] >> [SCAN MODE] >> [STROBE] or 
[MANUAL] or [PHOTO] or [SCENE], whichever mode you 
prefer.
When [STROBE] is selected:
≥Set the [SPEED] to a desired strobe speed.
[FAST]: You can capture 9 consecutive still pictures within 
approximately 1 second
[NORMAL]: You can capture 9 consecutive still pictures within 
approximately 1.5 seconds
[SLOW]:You can capture 9 consecutive still pictures within 
approximately 2 seconds
≥If you set [SWING] on the [MULTI-PICTURES] Sub-Menu to [ON], the 
intervals at which the 9 still pictures are taken are longer at the 
beginning and end than in the middle of the swing strobe period, and it 
is useful for analyzing swing motion, etc., in sports.
2Exit the Menu by pressing the [MENU] Button.
3Play back the tape.
≥If you select Index mode, it is not necessary to play back the tape.
4Press the [MULTI] Button.
≥If [STROBE] is selected: 9 screens are automatically captured from 
the point at which the Button is pressed.
≥If [MANUAL] is selected: press the [MULTI] Button at each scene you 
want to capture. When 9 screens are captured, the tape will stop.
≥If [PHOTO] or [SCENE] is selected: From the point at which the 
Button is pressed, 9 screens of pictures to which index signals are 
attached are captured in the playback direction. After 9 screens are 
captured, the tape will stop, but, if there are 8 or less pictures to be 
captured, the tape will stop at its end.
Deleting All the Captured Multi-Pictures
While displaying the multi-pictures that have been captured, press the 
[MULTI] Button.
≥If [MANUAL] has been selected, press [MULTI] Button after 9 screens are 
displayed.
To Display the Multi-Pictures again
Press the [MULTI] Button for 1 second or longer.
To Delete Multi-Pictures one by one  (When Pictures have been 
captured in Manual Mode):
When the [MULTI] Button is pressed for 1 second or longer while the still 
pictures are displayed, the picture that was captured last is deleted. If you 
continue to press the Button, the pictures are deleted consecutively.
≥After still pictures are deleted one at a time, they cannot be displayed again.
To Stop Capturing Pictures midway (When Pictures have been 
captured in Index Mode)
Press the [∫] Button on the Remote Controller or push the Operation Lever 
towards [∫].
To Search the tape position of a desired picture among the 
playback pictures displayed on 9 screens
1
11 1After displaying pictures in Multi-Picture Mode, rotate the 
[PUSH] Dial to select the image whose tape position you 
want to search.
≥The selected picture is marked with a red frame.
2
22 2Press the Index Button [:] or [9] 4 on the Remote 
controller.
≥Still picture playback takes place at the selected picture.
≥For other notes, see page 61.

						

							34
A.DUB;A.DUB!
12
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
4
3
3, 5
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGSEARCHAUTOMANUAL
1, 2
Playing Back on Your TV
By connecting your Palmcorder with your TV, the recorded scenes can be 
viewed on your TV screen.
≥Before connecting them, turn off the power of both the Palmcorder and TV.
1Connect the [A/V IN/OUT] Jack of the Palmcorder to the 
Video and Audio Input Jacks of the TV.
≥Using the A/V Cable 1 (supplied), make a connection with the 
TV. If the TV has an S-Video Jack, connect the S-Video Cable 
(not supplied) 
2, too.
Making the Indications Appear on the TV screen
Press the [OSD] Button 3 on the Remote Controller.
≥Be sure to select the proper input on your TV. (If necessary, consult your 
TV’s operating instructions.)
≥If you play back a Cassette recorded with copyright protection signals, the 
screen becomes blue or mosaic-like noise patterns appear.
≥If you set [AV JACK] on the [AV IN/OUT SETUP] Sub-Menu to [IN/OUT], 
nothing will be shown on the TV screen except during playback.
~~~~~~~~~~~~~~~~~~~~~~~~
Audio Dubbing
You can add music or narration to the recorded Cassette.
≥If you perform audio dubbing onto a tape that was recorded with 
[AUDIO-REC] on the [RECORDING SETUP] Sub-Menu of the 
[CAMERA FUNCTIONS] Main-Menu set to [16bit], the original sound is 
erased.
 (If you want to preserve the original sound, use the [12bit] Mode 
when recording.)
≥Audio Dubbing cannot be performed onto recordings made in LP Mode. 
(l19)
1Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >> [AV JACK] 
>> [IN/OUT].
2And then select [A.DUB INPUT] >> [MIC] or [AV IN].
≥Set to [AV IN] when external sound equipment is used, or set to [MIC] 
when an external or built-in microphone is used.
3Press the [1] Button, and then press the [;] Button at the 
point where you want to start dubbing.
4Press the [A.DUB] Button on the Remote Controller.
≥[A.DUB;] Indication appears. 1
5
To start Audio Dubbing, press the [;] Button on the Remote 
Controller.
≥[A.DUB!] Indication appears. 2
To Stop Audio Dubbing
Press the [;] Button on the Remote Controller.
The Palmcorder is in the Still Playback Mode again.
Playing Back the Sound Recorded with Audio Dubbing 
(For 12 bit Audio Recording)
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> [AUDIO] >> [ST2] 
or [MIX].
ST1: Play back only the original sound.
ST2: Play back only the sound added by Audio Dubbing
MIX: Play back both the original sound and the sound added by Audio 
Dubbing simultaneously.
≥For other notes, see page 62.
[VIDEO IN][S-VIDEO IN]
1
[AUDIO IN]
[S-VIDEO IN/OUT]
2
ZOOM
INDEX INDEXSELECTSTORESTOP
KL∫
OSDCOUNTER
V/REWSTILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
WsVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSEFF/WSTILL ADV
MENU
ITEMSET
61 5;ED
VAR.
SEARCHP. B .
ZOOM
3
1
A/V IN/OUT
PHONES
S-VIDEO IN/OUT
D.STILL PICTURE
MIC TO PC
DV

						

							35
OPEN
1
2
3
2
1
STILLTAPE
CARD
F 7640
VOICE
1
2
5
MPEG4
PHOTO
SHOTCARD MODE
PICTURE
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGAUTOMANUAL
3, 4
Special Features
Using a Memory Card
A Card can be used to record files or play back files.
≥Use genuine SD Memory Card or MultiMediaCard only.
ªInserting a Card
Before inserting a Card, be sure to turn off the Palmcorder.
1Slide the [OPEN] Lever to the right and open the Card Slot 
Cover.
2While holding the Card with its cut corner facing right 1, 
insert it into the Card Slot.
3Close the Card Slot Cover.
Taking out a Card
Open the Card Slot cover and push the side of the card in the middle and 
then pull it straight out to remove the card.
≥After removing the card, close the Card Slot cover.
ª[ACCESS] Lamp
While the Palmcorder is accessing the Card (reading, recording, playback, 
erasing, moving of images), the [ACCESS] Lamp 2 lights up.
≥While the [ACCESS] Lamp is on, never attempt to: open the Card Slot 
Cover, pull out the Card, turn off the Palmcorder power, or switch the 
[TAPE/CARD] Selector. Such actions will damage the Card and cause the 
Palmcorder to malfunction.
~~~~~~~~~~~~~~~~~~~~~~~~~
Recording on the Memory Card
Three kinds of data can be recorded by selecting with the 
[STILL/MPEG4/VOICE] Selector. When recording still pictures, select [STILL] 
(Card PhotoShot), when recording moving pictures, select [MPEG4] (MPEG4 
Recording), when recording voice, select [VOICE] (Voice Recorder Function).
≥If the [TAPE/CARD] Selector is set to [CARD], the Palmcorder is 
automatically turned off when you leave it for about 5 minutes without 
performing any PhotoShot recording.
≥When the [TAPE/CARD] Selector is set to [CARD], you cannot record to the 
Tape.
ªCard PhotoShot
Still pictures can be recorded on the Memory Card from the Palmcorder lens 
as well as from scenes that have already been recorded on a cassette.
The size of images that are recorded using this Palmcorder is approximately 
1,230,000 pixels. Recording of images with a size that is larger than a million 
pixels is called mega-pixel still-picture recording. Compared to images of 
normal recording, images that are created by mega-pixel still-picture 
recording can be printed out more clearly.
Recording from the Palmcorder Lens (Camera Mode)
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [STILL].
3Set [CAMERA FUNCTIONS] >> [CARD SETUP] >> 
[PICTURE SIZE] >> [1280k
kk k960] or [640k
kk k480].
4Set the [PICTURE QUALITY] to desired picture quality.
5Press the [PHOTO SHOT] Button.
≥The [ ] Indication will light in red.
≥Mega-pixel recording (when you select [1280k960] in step 3) is useful for 
taking clear pictures, but the following functions are disabled during mega-
pixel recording.
≥Digital zooming (l22)
≥Digital Effect functions (l27, 28)
≥Title In/Creation (l41)
≥The power is automatically turned off after about 5 minutes when a card has 
been inserted.PICTURE

						

							36
TAPE
CARD
F 7640
1, 2
2, 3
4, 4
PHOTO
SHOT
STILLVOICE MPEG4
CARD MODE
PICTURE
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGAUTOMANUAL
3, 1, 1
1
NOW WRITING;
TAPE
CARD%
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGSEARCHAUTOMANUAL
21
ªCard PhotoShot (continued)
Recording from a Cassette (VCR Mode)
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [STILL].
3Set [VCR FUNCTIONS] >> [CARD SETUP] >> 
[PICTURE QUALITY] >> a desired picture quality.
4Start playback and press the [PHOTO SHOT] Button at the 
scene you want to record.
≥The size of the images input externally or recorded from a tape to the 
card becomes [640k480].
≥While the image is being recorded, it stays still for a few seconds.
Recording from other equipment 
1
11 1Set [CAMERA FUNCTIONS] or [VCR FUNCTIONS] >> 
[CARD SETUP] >> [PICTURE QUALITY] >> a desired picture 
quality.
2
22 2Slide the [TAPE/CARD] Selector to [CARD].
3
33 3Slide the [STILL/MPEG4/VOICE] Selector to [STILL].
4
44 4Input the picture from the other equipment then press the 
[PHOTO SHOT] Button at the desired scene.
Selecting the quality of Card PhotoShot images
1Set [CAMERA FUNCTIONS] or [VCR FUNCTIONS] >> 
[CARD SETUP] >> [PICTURE QUALITY] >> a desired picture 
quality.
Maximum number of images recordable on the supplied Card (8MB)
When the picture size is 1280t960:
[FINE] (high image quality):approximately 8 pictures
[NORMAL] (Normal): approximately 14 pictures
[ECONOMY] (low image quality):approximately 20 pictures
When the picture size is 640t480:
[FINE] (high image quality):approximately 45 pictures
[NORMAL] (Normal): approximately 95 pictures
[ECONOMY] (low image quality):approximately 190 pictures
≥For other notes, see page 62. 
~~~~~~~~~~~~~~~~~~~~~~~~ªAutomatically copying still pictures recorded on a 
cassette
The Palmcorder copies images automatically, referring to Photo Index 
signals.
After setting the Palmcorder to the VCR Mode (l29).....
1Set the Palmcorder to Still Playback Mode just before the 
point where picture transfer is to commence.
2Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[RECORD TO CARD] >> [YES].
≥Search starts from the current Cassette position, and images with 
Photo Index signals are recorded onto the Card sequentially.
≥While copying, the Indication 
1 appears.
To Stop the Transfer of Images
Push the Operation Lever towards [∫].
≥For other notes, see page 62. 

						

							37
ªRecording the Moving Pictures (MPEG4)
You can record moving pictures for e-mailing on a Memory Card. The 
recorded data can be also played back on Windows Media Player.
Recording from the Palmcorder Lens (Camera Mode)
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [MPEG4].
3Press the Recording Start/Stop Button.
≥It takes 2 to 3 seconds to start recording.
≥During recording, the [ ] Indication appears and is lit in red. 
≥The maximum continuous recording time is 60 minutes
The Palmcorder will automatically stop recording when the relevant 
time listed above has elapsed.
≥When Remaining Time Indication becomes [R:0h00m], 
[NO SPACE LEFT] Indication appears. Recording may not be started.
≥The shutter speed is adjustable within the range of 1/30 to 1/500 while 
recording moving pictures (MPEG4).
≥The picture size of the moving picture (MPEG4) is set to be [176k144].
≥When attaching to email, we recommend the picture size to be less than 
1MB (about 1 minute length).
≥The following functions are disabled.
≥Digital Zoom (l22)
≥Cinema Function (l23)
≥Digital Effect Functions (l27)
≥Title In/Creation (l41)
≥Fade In/Out Function (l22)
Recording from a Cassette (VCR Mode)
1
11 1Slide the [TAPE/CARD] Selector to [CARD].
2
22 2Slide the [STILL/MPEG4/VOICE] Selector to [MPEG4].
3
33 3Start playback and press the Recording Start/Stop Button at 
the desired scene.
Recording from an other equipment (VCR Mode)
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [MPEG4].
3Input the image from other equipment then press the 
Recording Start/Stop Button at the desired scene.
Maximum recording time on the supplied Card (8 MB)
Approximately 6 minutes
≥The video resolution of the camera is reduced when making an MPEG4 
recording. This is done in order to optimize the image quality in MPEG4 
recordings, and does not reflect a problem with the software or hardware.
≥For other notes, see page 62.
ªRecording Voice (Voice Recording Function)
You can record voice data on a Memory card.
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [VOICE].
3Press the Recording Start/Stop Button.
≥Voice from built-in microphone is recorded.
≥It takes 2 to 3 seconds to start recording.
≥The recorded file is automatically locked (to prevent accidental 
erasure).
≥Voice from external microphone connected to the microphone jack can 
also be recorded.
≥During recording, the [ ] Indication appears and is lit in red. 
≥If a card is not inserted, the Indication flashes in red.
≥When Remaining Time Indication becomes [R:0h00m], 
[NO SPACE LEFT] Indication appears. Recording may not be started.
≥For other notes, see page 62.
MPEG4MPEG4
VOICE
1, 1, 1
2, 2, 2
3, 3, 3
TAPE
CARD
STILLVOICE MPEG4
CARD MODE
R:0h20mMPEG4
2
3 1
TAPE
CARD
STILLVOICE MPEG4
CARD MODE
R:0h20mVOICE

						

							38
Playing Back Files from the Memory Card
It allows you to play back files recorded on a Card.
≥When you set the Palmcorder to Card Playback Mode, the Card Contents 
1 are displayed to inform you which kind(s) of data (still picture, moving 
picture and/or voice data) are recorded on the Card.
ªPlaying back Still Pictures
1
Set the Palmcorder to Card Playback Mode.
≥The [CARD P.B.] Lamp lights up.
≥The still picture that was recorded last on the Card is displayed.
2Set the [STILL/MPEG4/VOICE] Selector to [STILL].
3Start Playback.
1: Starts Slide Show (The [SLIDE!] Indication is displayed)
5: Playing back the next Picture
6: Playing back the previous Picture
∫: Stop the slide playback
;: Pause slide playback
ªPlaying back Moving Pictures (MPEG4) 
1
11 1
Set the Palmcorder to Card Playback Mode.
≥The [CARD P.B.] Lamp lights up.
2
22 2Set the [STILL/MPEG4/VOICE] Selector to [MPEG4].
3
33 3Start Playback.
1: Playing back
∫: Stop the playing back
;: Pause playing back (This button does not pause playing back within 
2 seconds of finishing playing back.)
5: (Stop Mode)To the beginning of the next file.
(Playback Mode)To the beginning of the next file picture and start 
playback.
(Pause Mode)To the beginning of the next file and turns to Stop Mode.
6: (Stop Mode)To the beginning of the previous playback file.
(Playback Mode)To the beginning of the playback file and start playback.(Pause Mode)To the beginning of the file under playback and turns to 
Stop Mode.
≥File is numbered in hexadecimal form.
≥When the object is moving fast or zoom operation is performed, picture may 
appear to be still or a mosaic noise pattern appears, but this is not a 
malfunction.
ªPlaying back Voice 
1Set the Palmcorder to Card Playback Mode.
≥The [CARD P.B.] Lamp lights up.
2Set the [STILL/MPEG4/VOICE] Selector to [VOICE].
3Start Playback
1: Playing back
∫: Stop the playing back
;: Pause playing back (This button does not pause playing back within 
2 seconds of finishing playing back ).
5: (Stop Mode) To the beginning of the next File.
(Playback Mode) To the beginning of the next File and start playback. 
(Pause Mode) To the beginning of the next File and turns to Stop Mode.
6: (Stop Mode) To the beginning of the previous playback File.
(Playback Mode) To the beginning of the playback File and start 
playback.
(Pause Mode) To the beginning of playback File and turns to Stop 
Mode.
≥If the Operation Lever is pushed towards [6] or [5] for 1 or more 
seconds, it becomes 10k playback and if pushed for 7 or more seconds, it 
becomes 60k playback. Releasing the Operation Lever brings back to 
normal playback.
2 Folder-File Number (When the picture or MPEG4 is played back only)3 Picture Size (When the picture is played back) 
Playback time (When MPEG4 data or Voice data is played back)
4 File Number
To adjust the volume (Only Playing back MPEG4 and Voice)
≥During playback, hold down the [PUSH] Dial until the volume indication 
appears and rotate it to adjust the volume. (l29)
CAMERA
VCR
CARD P.B.
STILLVOICE MPEG4
CARD MODE
1, 1, 1
2, 2, 2
3, 3, 3
SEARCH
MODE
ON
OFF
POWER
2 1
3
4
3
4
MPEG4
3
4 2
VOICE
CARD CONTENTS
PICTURE
MPEG4
VOICE
100-0012

						

							39
1
TAPE
CARD
STILLVOICE MPEG4
CARD MODE
1
3
54PICTURE
No.25         100-0012
2
640
640
640
640
640
640
No.3
FILE SEARCH
PUSH MENU TO RETURN
2, 4
MULTI/P-IN-P
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGAUTOMANUAL
3, 4
1, 2 1
ªTo Select a Desired File and Play it Back
After setting the Palmcorder to the Card Playback Mode (l38).....
1Slide the [STILL/MPEG4/VOICE] Selector to desired type of 
data.
2Press the [MULTI] Button.
≥The files recorded on the Memory Card are displayed in Multi-Picture 
Mode. 
1
3
Rotate the [PUSH] Dial and select a desired file.
≥The selected file is marked with a red frame.
≥When 7 or more files have been recorded, rotate the [PUSH] Dial to 
display the next file. The Operation Lever (towards [6] or [5])can 
be used instead of the [PUSH] Dial.
4Press either the [PUSH] Dial or the [MULTI] Button.
≥The selected file is shown on the entire screen.2 File Size (When [STILL] is selected at Step 1)
3 File Number4 Folder-File Number (When [STILL] or [MPEG4] is selected at Step 1)
ªUsing File Search Mode
1
11 1
Set [CARD FUNCTIONS] >> [CARD EDITING] >> 
[FILE SEARCH] >> [YES].
≥The file search screen 5 appears.
2
22 2Rotate the [PUSH] Dial to select the desired number of the 
file and then press it.
≥The selected number’s file appears.
≥The same process can be performed using the short-cut menu (l18).
≥For other notes, see page 63. 
~~~~~~~~~~~~~~~~~~~~~~~~~Copying pictures on a Memory Card to a 
Cassette
After setting the Palmcorder to the Card Playback Mode (l38).....
To Copy One Picture
1Slide the [TAPE/CARD] Selector to [TAPE].
2Slide the [STILL/MPEG4/VOICE] Selector to [STILL].
3Display a desired picture.
≥Please refer to “To select a Desired File and Play it Back”.
4Press the [PHOTO SHOT] Button.
≥It takes approximately 7 seconds to copy a still picture to the Cassette.
≥During the copying, the indication 1 appears.
To Copy All the Pictures
1
11 1Display the first picture.
≥If a picture other than the first one is displayed, only the subsequent 
pictures will be copied.
2
22 2Set [CARD FUNCTIONS] >> [CARD EDITING] >> 
[RECORD TO TAPE] >> [YES].
≥It takes approximately 7–11 seconds for each picture to be copied to 
the cassette. To stop the copying midway, press the [∫] Button.
≥During the copying, the Indication 
1 appears.
≥When recording to tape, select the tape position before recording. The 
picture will be recorded to the tape position when the [PHOTO SHOT] 
button is pressed at step 4.
≥When picture with a size other than [640k480] are copied on the cassette, 
their pictures quality will deteriorate slightly.
≥Picture size recorded on tape is [640k480]. (Cannot save as mega-pixel 
still picture)
≥Moving Picture (MPEG4) and Voice data cannot be recorded from a card to 
tape.
≥When recording the Card Images on a Tape, a PhotoShot index signal is 
automatically recorded with a picture.
≥Even if you edit the Slide Show, it is not applied to the order in copying the 
pictures.
≥For other notes, see page 62.
1
NOW RECORDINGREC
1
2
STILL   VOICE MPEG4
CARD MODE
TAPE
CARD
4PHOTO
SHOT
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGAUTOMANUAL
2

						

							40
Slide Show
The recorded still pictures in the Card can be played back like a Slide Show.
You can set up a Slide Show or change the content.
To Select Pictures to Play Back in Your Slide Show
1After setting the [STILL/MPEG4/VOICE] Switch to [STILL], 
set [CARD FUNCTIONS] >> [CARD EDITING] >> 
[SLIDE SHOW] >> [YES].
≥Slide Show editing screen appears.
2Set [EDIT] >> [YES].
3Rotate the [PUSH] Dial to select a picture and then press the 
dial.
4Rotate the [PUSH] Dial to select playback order and then 
press the dial.
≥This step is skipped when there are no pictures that has set for the 
Slide Show.
5Rotate the [PUSH] Dial to adjust the playback time and then 
press the dial.
≥The Playback Order Indication 1 and the Playback Time (Second) 
Indication 
2 appear.
≥The [¥] Indication 3 is displayed below pictures that have been 
selected for the Slide Show.
≥To select the next picture, repeat the Steps 3 to 5 above.
6Press the [MENU] Button to end the setup.
7After setting [SLIDE SHOW] >> [PRESET], press the [MENU] 
Button.
8Push the Operation Lever towards [1].
≥The [M.SLIDE!] Indication is displayed. 4
To Play Back All the Pictures Continuously
After setting the [SLIDE SHOW] to [ALL], push the Operation Lever towards 
[1].
≥The [SLIDE!] Indication is displayed. 
5≥All pictures are played back for approximately 5 seconds each, from the first 
to the last recorded picture, and playback then stops.
To Pause the Slide Show
Push the Operation Lever towards [;].
≥The [(M.) SLIDE;] Indication is displayed. 6
To Stop the Slide Show
Push the Operation Lever towards [∫].
To Verify the Selected Picture
Set [CARD FUNCTIONS] >> [CARD EDITING] >> [SLIDE SHOW] >> [YES] 
>> [VERIFY] >> [YES].
≥Only the selected pictures are displayed in Multi-Picture Mode in the 
Playback order.
To Delete the Selected Pictures
1
11 1Set [CARD FUNCTIONS] >> [CARD EDITING] >> 
[SLIDE SHOW] >> [YES].
2
22 2Set [DELETE] >> [YES].
3
33 3Select the picture you want to delete and press the [PUSH] 
Dial.
To Reset the Slide Show Setup
Set [CARD FUNCTIONS] >> [CARD EDITING] >> [SLIDE SHOW] >> [YES] 
>> [RESET] >> [YES] >> [YES].
≥Slide Show settings are reset.
≥For other notes, see page 63.
EDIT
PUSH MENU TO RETURNNo.5
9SEC2
13
M.SLIDE
4
SLIDE
5
SLIDE
6
640
640
1280
640
640
1280
1STILL   VOICE MPEG4
CARD MODE
PUSHMENUW.B./SHUTTER/IRIS/
         VOL/JOGSEARCHAUTOMANUAL
1, 2, 3, 4, 
5, 7
1, 2, 3 8
1, 6, 7 
1