Panasonic Projector PT-DS20KU User Manual

[PICTURE] menu
ENGLISH - 71
Settings
[NOISE REDUCTION]
You can reduce noises when the input image is 
degraded and noise is occurring in the image signal.
1) Press ▲▼ to select [NOISE 
REDUCTION].
2)
 
Press  ◀▶ or the  button.
▶z
The  [NOISE REDUCTION] individual 
adjustment screen is displayed.
3) Press  ◀▶ to switch the [NOISE 
REDUCTION].
▶z The setting will change as follows each time 
you press the button.
[1] (Low)[2] (Medium)
[OFF] (No 
correction)[3] (High)
Attention
 z When this is set for an...

[PICTURE] menu
72 - ENGLISH
Settings
[SYSTEM SELECTOR]
The projector will automatically detect the input signal, 
but you can set the system method manually when 
an unstable signal is input. Set the system method 
matching the input signal.
1) Press ▲▼ to select [SYSTEM 
SELECT OR].
2)
 
Press the  button.
3)

 
Press  ▲▼ to select a system format.
4)

 
Press the  button.
▶■ When using  terminal, 
/ terminals
Select [AUTO], [NTSC], [NTSC4.43], [PAL], [PAL-M], 
[PAL-N], [SECAM], or [PAL60].
Attention
 z...

[PICTURE] menu
ENGLISH - 73
Settings
▶■When using  terminal, 
 terminal (PT
-DZ21KU 
and PT-DS20KU only)
▶z Single link
During SDI1 input, select [AUTO], [480i YCBCR], [576i 
YC
BCR], [720/50p YPBPR], [720/60p YPBPR], [1035/60i 
YP
BPR], [1080/24p YPBPR], [1080/24sF YPBPR], 
[1080/25p YP
BPR], [1080/30p YPBPR], [1080/50i 
YP
BPR], [1080/60i YPBPR], [1080/50p YPBPR], 
[1080/60p YP
BPR], [1080/24p RGB], [1080/24sF 
RGB], [1080/25p RGB], [1080/30p RGB], [1080/50i 
RGB], or [1080/60i RGB].
During SDI2 input,...

[POSITION] menu
74 - ENGLISH
Settings
Select [POSITION] from the main menu, and 
select the item from the sub-menu.
Refer to “Navigating through the menu” 
(
 page 63) for the operation of the menu 
screen.
 z After selecting the item, press 
▲▼◀▶ to set.
[SHIFT]
You can move the image position vertically or 
horizontally if the image position projected on the 
screen is shifted even when the relative position of the 
projector and the screen is installed correctly.
1) Press 
▲▼ to select [SHIFT].
2)...

[POSITION] menu
ENGLISH - 75
Settings
▶■[16:9]
When standard signals*1 are input, the pictures are 
displayed with the aspect ratio converted to 16:9. 
When wide-screen signals
*2 are input, the pictures are 
displayed without changing the aspect ratio.
▶■ [4:3]
When standard signals*1 are input, the pictures are 
displayed without changing the aspect ratio. When 
wide-screen signals
*2 are input and [4:3] is selected in 
[SCREEN FORMAT], the pictures are displayed with 
the aspect ratio changed to 4:3....

[POSITION] menu
76 - ENGLISH
Settings
[CLOCK PHASE]
You can adjust to achieve an optimal image when 
there is a flickering image or smeared outlines.
1) Press ▲▼ to select [CLOCK PHASE].
2)  
Press  ◀▶ or the  button.
▶z
The  [CLOCK PHASE] individual adjustment 
screen is displayed.
3) Press  ◀▶ to adjust the level.
▶z
Adjustment value will change between [0] and 
[
31]. Adjust so that the amount of interference is 
at a minimum.
Note
 z Certain signals may not be adjustable.
 zOptimal value may not be...

[POSITION] menu
ENGLISH - 77
Settings
▶z[LENS THROW RA TIO]
Set the throw ratio for the lens used.
▶z
[VERTICAL  KEYSTONE]
▶z
[HORIZONT AL KEYSTONE]
▶z
[VERTICAL  BALANCE]
Adjust the setting according to the lens shift range 
in vertical direction.
▶z
[HORIZONT AL BALANCE]
Adjust the setting according to the lens shift range 
in horizontal direction.
▶■To set [CURVED]
3) Select [CUR
VED] in Step 2), and press 
the  button.
▶z The  [GEOMETRY:CURVED] screen is 
displayed.
4) Press  ▲▼ to select the item...

[POSITION] menu
78 - ENGLISH
Settings
4) Press ▲▼ to select the item to adjust, 
and press the  button.
5)
 
Press  ▲▼◀▶  to adjust the correction 
amount.
▶z The projected image can be corrected.
▶z[UPPER LEFT]
▶z[UPPER RIGHT]
▶z[LOWER LEFT]
▶z[LOWER RIGHT]
▶z[LINEARITY]
Horizontal direction
Vertical direction
Note
 z The menu or logo may extend beyond the edge of 
the screen when [GEOMETR

Y] is set.
 zIf [EDGE BLENDING] ( page 81) adjustment and 
[GEOMETR
Y] are used together, correct edge 
blending...

[POSITION] menu
ENGLISH - 79
Settings
Note
 zThe menu or logo may run of

f the screen 
when various adjustments are performed with 
[KEYSTONE].
 z V

arious adjustments with [KEYSTONE] are 
possible to correct up to ±40° for the tilt in vertical 
direction. However, the picture quality will degrade 
and it will get harder to focus with more correction. 
Install the projector so the correction will be as 
small as possible. (±22° when using projection lens 
ET-D75LE5/ET-D75LE50, or ±28° when using the...

[ADVANCED MENU]
80 - ENGLISH
Settings
Select [ADVANCED MENU] from the main 
menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” 
(
 page 63) for the operation of the menu 
screen.
 z After selecting the item, press 
▲▼◀▶ to set.
[DIGITAL CINEMA REALITY]
You can increase the vertical resolution and enhance 
the picture quality by performing the cinema 
processing when the PAL (or the SECAM) 576i signal, 
the NTSC 480i, 1080/50i, and 1080/60i signals are 
input.
1) Press...