Panasonic Projector PT-DS20KU User Manual

[DISPLAY OPTION] menu
ENGLISH - 101
Settings
2) Press ◀▶ to switch [W
AVEFORM 
MONITOR].
▶z The setting will change as follows each time 
you press the button.
[OFF][ON]
3) Press the  button two times to 
clear
.
4)
 
Press  ▲▼ to select any horizontal 
line.
▶z Items switch as in the following diagram 
each time the  is pressed while the 
waveform monitor is displayed.
“Select line (luminance)”“Select line (red)”
“Select line (blue)”“Select line (green)”
Note
 z T

he [FUNCTION BUTTON] (
 page 114) can...

[PROJECTOR SETUP] menu
102 - ENGLISH
Settings
[PROJECTOR SETUP] menu
Select [PROJECTOR SETUP] from the main 
menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” 
(
 page 63) for the operation of the menu 
screen.
 z After selecting the item, press 
▲▼◀▶ to set.
[PROJECTOR ID]
The projector has an ID number setting function that 
can be used when multiple projectors are used side 
by side to enable simultaneous control or individual 
control via one remote control.
1)...

[PROJECTOR SETUP] menu
ENGLISH - 103
Settings
[COOLING CONDITION]
Change the fan control depending on the direction of 
projection.
Set [COOLING CONDITION] according to the 
projection direction, but set it to [AUTO] normally. 
Using the projector with [COOLING CONDITION] set 
incorrectly may shorten the life of the lamp.
1) Press ▲▼ to select [COOLING 
CONDITION].
2)
 
Press the  button.
▶zThe  [COOLING CONDITION]  screen is displayed.
3) Press ▲▼ to select a cooling condition.
▶zW hen [AUTO] is...

[PROJECTOR SETUP] menu
104 - ENGLISH
Settings
[L1]Lamp 1 will light.
[L2] Lamp 2 will light.
[L3] Lamp 3 will light.
[L4] Lamp 4 will light.
[L1/L4] Lamp 1 and Lamp 4 will light.
[L2/L3] Lamp 2 and Lamp 3 will light.
[L1/L2/L3]
Lamp 1, Lamp 2 and Lamp 3 will light.
[L1/L2/L4]Lamp 1, Lamp 2 and Lamp 4 will light.
[L1/L3/L4]Lamp 1, Lamp 3 and Lamp 4 will light.
[L2/L3/L4]Lamp 2, Lamp 3 and Lamp 4 will light.
[SINGLE] (1 lit) One lamp will light. (A short usage 
time lamp will automatically light.)
[DUAL]...

[PROJECTOR SETUP] menu
ENGLISH - 105
Settings
times. Next, four lamps turn on eight hours after the 
specified time and thereafter three lamps switch 
again after the specified time.
 zT

he operating time will be the local time. (
 page 114)
 z U

se the number ( to ) buttons on the remote 
control to directly enter the time.
[BRIGHTNESS CONTROL]
The projector is equipped with a luminance sensor to 
measure brightness and color of the lamp, and functions 
to correct brightness and color of the screen...

[PROJECTOR SETUP] menu
106 - ENGLISH
Settings
▶zSetting [MODE] to [AUT O]
8)  
Press  ▲▼ to select [LINK].
9)

 
Press  ◀▶ to switch [LINK].
▶z
The setting will change as follows each time 
you press the button.
[OFF][GROUP A]
[GROUP D][GROUP C][GROUP B]
[OFF] Uses the luminance sensor on one 
projector to perform correction without 
connecting another projector.
The length of time that constant 
brightness can be maintained increases 
as the [BRIGHTNESS CONTROL 
GAIN] value decreases.
[GROUP A]
[GROUP...

[PROJECTOR SETUP] menu
ENGLISH - 107
Settings
correction exceeds the maximum correction 
amount.
 zIn certain projector environments, dust may 
accumulate on the lens or screen or inside the 
projector and increase variation in brightness.
 zAdjust luminance control again when lamp 
degradation causes increased variation in 
brightness or a lamp is replaced.
 zFor continued use longer than 24 hours, set 
the [BRIGHTNESS CONTROL

 SETUP] to 
[CALIBRATION TIME], or set [LAMP RELAY] 
(
 page 104)....

[PROJECTOR SETUP] menu
108 - ENGLISH
Settings
▶zError details
Error message
Remedy
[Exceed maximum 
number of projectors.]
 z Set no more than eight 
projectors in one group.
 zUse a computer and 
the dedicated “Multi 
Projector Monitoring & 
Control Software”
*1 to 
connect nine or more 
projectors.
[Please check the 
COMMAND CONTROL 
setting.]
 z Set the on-screen menu 
[NETWORK CONTROL] 
[COMMAND CONTROL] 
to [ON] for the projector 
in error

.
 z Set the [NETWORK 
CONTROL] [COMMAND 
POR

T] of all...

[PROJECTOR SETUP] menu
ENGLISH - 109
Settings
10) Set [BRIGHTNESS CONTROL GAIN] 
of all projectors to 100%.
11) Set [BRIGHTNESS CONTROL GAIN] 
of the darkest projector to 90%.
12) Adjust [BRIGHTNESS CONTROL 
GAIN] to match the [BRIGHTNESS 
CONTROL GAIN] set to 90% of the 
other projectors.
13) Set [MODE] in [BRIGHTNESS 
CONTROL SETUP] of all projectors to 
[AUTO], and [LINK] to [GROUP A].
14) Select [APPLY] in [BRIGHTNESS 
CONTROL SETUP] on all projectors 
and press the  button.
▶zLuminance control...

[PROJECTOR SETUP] menu
110 - ENGLISH
Settings
10) Press ◀▶ to switch [COMMAND].
▶z
The setting will change as follows each time 
you press the button.
[POWER ON][STANDBY][SHUTTER]*1
[P IN P]*1[LAMP 
SELECT]*1[INPUT]*1
*1: Displays the details set in Step  12) .
11) Press the  button.
▶zThe [COMMAND] detailed setting screen is 
displayed.
12) Press 
▲▼ to select a command.
▶z
For [SHUTTER], [INPUT], [LAMP  SELECT], 
and [P IN P], the setting will change as follows 
each time you press the button.
▶z...