Panasonic Projector PT-DS20KU User Manual

Precautions for use
ENGLISH - 21
Important 
Information
Optional accessories
Optional accessories 
(product name) Model No.
Projection lens ET-D75LE6 (Zoom Lens),
ET-D75LE8 (Zoom Lens),
ET-D75LE10 (Zoom Lens),
ET-D75LE20 (Zoom Lens),
ET-D75LE30 (Zoom Lens),
ET-D75LE40 (Zoom Lens),
ET-D75LE50 (Fixed-Focus Lens)
Ceiling mount bracket ET-PKD510H (for high ceilings), ET-PKD510S (for low ceilings)
Frame ET-PFD510
Replacement lamp unit ET-LAD510 (1 pc), ET-LAD510F (4 pcs)
Replacement lamp unit (for 
portrait...

Start-up display
22 - ENGLISH
Preparation
Start-up display
When the projector is switched on for the first time after purchase as well as when [ALL USER DATA] ( page 117) 
in [INITIALIZE] is executed, the focus adjustment screen is displayed after projection starts, then the [INITIAL  
SETTING] screen is displayed. Set them in accordance with circumstances.
In other occasions, you can change the settings by menu operations.
▶■ Focus adjustment
Adjust the focus to display the menu screen clearly.
You may...

Start-up display
ENGLISH - 23
Preparation
▶■Initial setting (installation setting 2)
Set [COOLING CONDITION] depending on the 
projection method. Refer to “Projection method” 
(
 page 30) for details.
After completed the initial setting, you can change 
the setting from the [PROJECT
OR SETUP] menu → 
[COOLING CONDITION].
1) Press  ◀▶ to switch the setting.
If the clasps are attached to the lamp case, please 
remove them. For details, please refer to the enclosed 
leaflet [Notice to User when Installing...

About your projector
24 - ENGLISH
Preparation
About your projector
Remote control
▶■Front
(1) Remote control indicator
Flashes if any button in the remote control is pressed.
(2) Power standby <
> button
Sets the projector to the standby mode when the  switch on the projector is set to .
(3) Power on <
> button
Starts projection when the  switch on 
the projector is set to  when the power is switched 
off (standby mode).
(4) Input selection (, , ,  , , ) buttons
Switches the input signal to project. (
...

About your projector
ENGLISH - 25
Preparation
(19)  buttonUsed to prevent unintended operation by careless pressing of the buttons and prevent draining the remote control batteries.
Attention
 zDo not drop the remote control.
 zA

void contact with liquids or moisture.
 zDo not attempt to modify or disassemble the remote control.
Note
 z The remote control can be used within a distance of about 30 m (98'5") if pointed directly at the remote control 
r

eceiver. The remote control can control at...

About your projector
26 - ENGLISH
Preparation
Projector body
▶■Front
 ■ Rear
▶■Side
 

   
)URQW
 
)URQW (1) Power indicator 
The power indicator displays power status.
(2) Lamp indicator  Displays the status of lamp 1.
(3) Lamp indicator  Displays the status of lamp 2.
(4) Lamp indicator  Displays the status of lamp 3.
(5) Lamp indicator  Displays the status of lamp 4.
(6) Temperature indicator  Displays the internal temperature status.
(7) Filter...

About your projector
ENGLISH - 27
Preparation
 ■Bottom


)URQW (22) Burglar hook port
You can attach a commercial burglar prevention cable.
Attention
 zKeep your hands and other objects away from the 
air exhaust port.
–

▶
Keep your hands and face away
 .
–
▶
Do not insert your fingers.
–

▶
Keep heat-sensitive objects away
 .
Heated air from the air outlet port can cause bums, 
injury, or deformations.
 z Do not block the ventilation ports (intake and 
exhaust) of the projector

.
▶■Control...

About your projector
28 - ENGLISH
Preparation
▶■Connecting terminals
▶z
For PT -DZ21KU, PT-DS20KU
(1) (2) (3) (4)
(5) (6) (7)(8) (9) (10) (11) (12)
▶zFor PT -DW17KU
(1) (2) (3) (4)
(6) (7) (8) (9) (10) (12)
(1)  terminal /  terminal
These are the terminals to connect the remote control for 
serial control when the system uses multiple projectors.
(2)  terminal This is a terminal to remotely control the projector using 
the external control circuit.
(3)  terminal This is a RS-232C compatible terminal to...

Using the remote control
ENGLISH - 29
Preparation
Using the remote control
Inserting and removing the 
batteries
1) Open the cover.
(i)
(ii)
2) Insert the batteries and close the cover 
(insert the 
 side first).
▶zWhen removing the batteries, perform the steps 
in reverse order
.
Setting Remote control ID 
numbers
When you use the system with multiple projectors, 
you can operate all the projectors simultaneously or 
each projector individually using single remote control, 
if a unique ID number is...

Setting up
30 - ENGLISH
Getting Started
Setting up
Projection method
You can use the projector with any of the following six projection methods. Set [PROJECTION METHOD] 
depending on the installation location. Set [COOLING CONDITION] to [AUTO]. Using the projector with [COOLING 
CONDITION] set incorrectly may shorten the life of the lamp.
▶■Mounting on the ceiling and 
projecting forward▶■Setting on a desk/floor and 
projecting from rear
(Using the translucent screen)
Menu item*1Method
[PROJECTION...