Panasonic Network Camera Management SystemKx Hgw600 Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 41
Setup
Turning on the Devices
After completing the connection between the PC and the KX-HGW600, make sure the
PC is turned off and follow the steps below.
1.Insert the cable clamper into the cable clamper hole of the KX-HGW600 until you
hear a click.
2.Connect the DC plug of the AC adaptor to the DC IN jack and the AC plug of the
AC adaptor to the power outlet.
Notes
 AC adaptor is used as the main disconnect device, ensure that the
socket-outlet is located/installed near the equipment and is easily accessible.
 Use Only with specified Panasonic AC adaptor PQLV12Y.
Cable clamper
(included accessory)
Power Outlet
(AC 120V)
AC adaptor
(included accessory)
DC plugDC IN jack 
						

							Operating Instructions
42
3.Fix the AC adaptor cord with the cable clamper.
4.Turn on the PC connected to the KX-HGW600.
Note
Make sure the indicators light green ( Page 13).
AC adaptor cord
Thread the AC adaptor
cord through the cable clamper.
Close the cable clamper firmly. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 43
Setup
2.3.2 Setting up the KX-HGW600
Confirming the KX-HGW600 Setup
The KX-HGW600 has an integrated web server. If you can access the Camera Portal
page, the network configuration between the KX-HGW600 and the PC has been
successfully made.
1.Start up your web browser.
2.Enter http://192.168.0.254(:Port No.) in the address field of your web browser.
The Camera Portal page appears.
If the Camera Portal page does not appear (Page 141)
 Make sure the indicators light green.
 Make sure the KX-HGW600 is turned on first, then the PC.
 The proxy server setting of your web browser may be needed to access the
Camera Portal page. For more information, please refer to Page 126.
3.Click[Setup Page].
The authentication window appears.
4.Enter KX-HGWinthePassworddata field.
Leave theUser Namedata field blank. 
						

							Operating Instructions
44
5.Click[OK].
The Basic Setup window appears.
Notes
 You can change the password on the Setup Page. Please refer to Change
PasswordonPage110.
 For more information about the Setup Page, please refer to Setup Page on
Page 68. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 45
Setup
Setting up LAN (Intranet) Configuration
To connect the KX-HGW600 to the LAN (Intranet), static IP address is needed.
When your network administrator provides you with Static Connection, follow the steps
below.
1.Click[Basic Setup]on the Setup Page.
SELECTEDis displayed next to the configuration type which is currently
selected.
2.Click[Static Connection].
Static IP address
LAN (Intranet)
Ethernet hub
Private IP address
192.168.0.113
Private IP address
192.168.0.114 Private IP address
192.168.0.1 
						

							Operating Instructions
46
3.EnterIP Address,Subnet Mask,Gateway,DNS Server 1and
DNS Server 2. If requested by your network administrator, enterDomain Name.
For each input value, please refer to network information on Page 38.
 To clear the current settings, click[Clear].
Note
Do not enter the space in each data field.
4.When you have finished, click[Save]. The settings will be saved.
5.Click[Restart Now!].
Next, confirm the LAN (Intranet) Configuration ( Page 47). 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 47
Setup
Confirming the LAN (Intranet) Configuration
After completing your LAN (Intranet) configuration, if you can access the Camera Portal
page from the PC on the LAN (Intranet), the connection between the LAN (Intranet) and
the KX-HGW600 has been successfully made.
1.From the PC on the LAN (Intranet), start up your web browser.
2.Enter the IP address(:Port No.) assigned on the Basic Setup window ( Page
38) in the address field of your web browser. The Camera Portal page appears.
 When port no. is 80 (default setting), you do not need to enter port no.
If the Camera Portal page does not appear ( Page 141)
 Make sure the IP address assigned on the Basic Setup window has been
correctly entered in the address field of the web browser.
 Make sure the connection between the KX-HGW600 and the Ethernet hub
has been successfully made.
 Make sure the WAN indicator on the KX-HGW600 and the indicator on the
Ethernet hub light green.
 The proxy server setting of your web browser may be needed to access the
Camera Portal page ( Page 126). 
						

							Operating Instructions
48
2.3.3 Connecting your Network Camera
Setting up your Network Camera automatically
Once you connect your Panasonic Network Cameras (KX-HCM series) to the
KX-HGW600 and turn them on, the network settings such as IP address, port no. are
configured automatically by the Automatic Setup function. After completing the LAN
(Intranet) configuration, make sure the target Network Camera is turned off and follow
the steps below.
1.a) To connect the KX-HGW600 and Network Camera with an Ethernet cable,
connect the Ethernet cable to one of the LAN 1—4 jacks of the KX-HGW600
and the other end to the Ethernet jack of the Network Camera.
Note
All Ethernet jacks have an automatic MDI/MDIX feature, which means either a
straight or cross cable can be used to connect to any jack. The KX-HGW600
will automatically detect which cable has been inserted.
Ethernet cable
Ethernet jack
b) To connect the KX-HGW600 and Network Camera in the wireless network,
locate the wireless Network Camera near the KX-HGW600.
To modem
To P C
LAN1—4 jacks 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 49
Setup
2.Turn on the Network Camera.
3.PushCLEAR SETTINGbutton on the Network Camera.
The Network Camera starts to communicate with the KX-HGW600 that control
transmission paths on the network. After that, the Network Camera screen is
registered on the Camera Portal page.
 The Automatic Setup function automatically configures the following network
settings.
 The Automatic Setup function assigns each port number and IP address in
the following order.
Setting up your Network Camera manually
 To set up your Network Camera manually, please refer to Page 75.
 To set up the specific Network Camera manually, clear[Enable]check box on the
Network window of Network Camera([Network] 1. Network Configuration
from the Setup Program). For more information, please refer to the Network
Camera’s manual.KX-HGW600Port Forwarding
Camera Entry
Screen Assignment
Network CameraPor t No.
IP Address
Subnet Mask
Default Gateway
DNS Server Address
Camera Name
Por t No. IP Address
Cam 01
Cam 02
Cam 03



Cam 1660001
60002
60003



60016192.168.0.113
192.168.0.114
192.168.0.115



192.168.0.128 
						

							Operating Instructions
50
2.3.4 Viewing the Network Camera screen
You can view the Network Camera screen on the Camera Portal page.
1.a) Enter http://192.168.0.254(:Port No.) in the address field of your web
browser. The Camera Portal page appears.
 When port no. is 80 (default setting), you do not need to enter port no.
b) Enter the IP address(:Port No.) on the WAN in the address field of your web
browser. The Camera Portal page appears.
 When port no. is 80 (default setting), you do not need to enter port no.
Note
To view the Network Camera screen from the WAN side, please refer to To
access the Camera Portal page from the WAN side on Page 79.
Image
field