Panasonic Network Camera Management SystemKx Hgw600 Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 111
System
Features
5.When the authentication window appears, enter the new user name and
password, then click[OK].
Note
If you forget the user name and the password after changing them, initialize the
KX-HGW600 to reset them to the default setting ( Page 124). 
						

							Operating Instructions
112
4.5.2 Update Firmware
Update Firmware windowallows you to install new firmware. To update the latest
firmware, download from the Panasonic web site(http://panasonic.co.jp/pcc/en/).
For more information, please follow the instructions of the Panasonic web site.
1.Click[Update Firmware]on the Setup Page.
2.Click[Browse...]to select the firmware.
TheChoose filedialog box appears.
3.Select the desired firmware file from the file list and click[Open].
The selected file name appears in theFile name. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 113
System
Features
4.Click[Upgrade]. The firmware is updated.
5.Click[Restart Now!].
Notes
 After updating, initialize the KX-HGW600 by pushing the FACTORY
DEFAULT RESET button ( Page 124) if required. For more information,
please refer to the Panasonic web site.
 When you use the DHCP server function ( Page 106), restart all the
devices on the LAN side.
Error Messages  If completed, the dialog box
appears. If not completed, an error message
appears. For more information,
please refer to Error Messages
below.
Error Messages Cause and Remedy
File size is invalid
CRC error occurredYour selected firmware file is damaged. If the firmware file
was downloaded from the Panasonic web site, download it
again.
Selected file is invalid
Update it again.Your selected firmware file is not for the KX-HGW600.
Reselect the proper file.
OR
Make sure your hardware version matches the firmware file
by reading the readme file that comes with the firmware file
( Page 118). If not, download the latest firmware from the
Panasonic web site.
Not enough memoryThe KX-HGW600’s internal memory has been depleted.
Restart the KX-HGW600 and update it again. 
						

							Operating Instructions
114
4.5.3 Restart
Restart windowallows you to restart the KX-HGW600. All the settings are preserved.
1.Click[Restart]on the Setup Page.
2.Click[Restart Now!].
The KX-HGW600 restarts.
Note
When you use the DHCP server function ( Page 106), restart all the devices
on the LAN side.
4.5.4 Factory Default Reset
Factory Default Reset windowallows you to initialize all the settings of the
KX-HGW600. All the settings return to their default settings ( Page 134).
1.Click[Factory Default Reset]on the Setup Page.
2.Click[Factory Default Reset Now!].
All the settings are initialized to the preset default settings.
Note
When you use the DHCP server function ( Page 106), restart all the devices
on the LAN side. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 115
System
Features
4.5.5 PPPoE Connection
PPPoE Connection windowallows you to manually initiate/stop your PPPoE
connection to the ISP.
To initiate the PPPoE Connection
1.Click[PPPoE Connection]on the Setup Page.
2.To initiate the PPPoE Connection, click[Connect].
To stop the PPPoE Connection
1.Click[PPPoE Connection]on the Setup Page.
2.To stop the PPPoE Connection, click[Disconnect].
Notes
 This function can be used regardless of the types of PPPoE Connection
(Always, Automatic, Manual).
 You cannot disconnect the PPPoE Connection from the WAN side. 
						

							Operating Instructions
116
Keep Alive Option
The KX-HGW600 has a Keep Alive Option function. When the server of your ISP
disconnects for some reason, this function keeps your PPPoE Connection alive
automatically. The main features are as follows.
 This function is only available when you checkAlwayson the PPPoE
Connection window.
 It tries to recover the connection by sending a few data packets in this
sequence:
1) After 1 minute, 3 minutes, 6 minutes.
2) Thereafter, once every ten minutes. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 117
System
Features
4.5.6 Ping
Ping windowallows you to confirm if each device on the WAN (Internet) or LAN side is
successfully linked to your KX-HGW600 on the TCP/IP network. When the device is
connected correctly and the power to the device is on, a Success! message appears
on the display.
1.Click[Ping]on the Setup Page.
2.Enter the IP address of the device (e.g., 192.168.0.1) you want to ping.
TocleartheIP Address,click[Clear].
3.Click[Ping].
 If completed, the dialog box
appears. If not completed, the dialog box
appears.
 The IP address might be invalid or
some other reasons might be
considered. 
						

							Operating Instructions
118
4.6 Information
4.6.1 Status
Status windowallows you to check the current IP address, the hardware and software
version information. This information may be helpful if you need to contact our customer
call center for assistance with the KX-HGW600.
1.Click[Status]on the Setup Page.
4.6.2 Usage Data
UsageDatawindowallowsyoutochecktheKX-HGW600statistics.
This information may be helpful if you need to contact our customer call center for
assistance with the KX-HGW600.
1.Click[Usage Data]on the Setup Page. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 119
System
Features
4.6.3 Packet Filtering Log
Packet Filtering Log windowallows you to check up to 4000 latest information
consisting of entry number, type, direction, the source or destination port number and
so on. If you enable logging on the Packet Filtering window, the KX-HGW600 will keep
a record of the packet information.
1.Click[Packet Filtering Log]on the Setup Page.
2.Click[Reload]to view the latest information.
 To delete the recorded log, click[Delete Log].
Note
When you restart the KX-HGW600, the information of Packet Filtering Log is
deleted. 
						

							Operating Instructions
120
4.6.4 User Registration
User Registration windowallows you to jump to the Panasonic web site for
registration. To help you register, the KX-HGW600 collects and displays the hardware
and software information of your KX-HGW600. You do not have to register the
information of a particular item if you do not want to.
1.Click[User Registration]on the Setup Page.
 If you do not want to register the information of an item, selectDo not send
from the drop-down menu.
 To clear the current settings, click[Clear].
2.Click[Submit]to register your KX-HGW600.
You will connect to the Panasonic web site. For more information, please follow
the instructions of the Panasonic web site.