Panasonic Network Camera Management SystemKx Hgw600 Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 21
Setup
Turning on the Devices
After completing the connection between the PC and the KX-HGW600, make sure the
PC is turned off and follow the steps below.
1.Insert the cable clamper into the cable clamper hole of the KX-HGW600 until you
hear a click.
2.Connect the DC plug of the AC adaptor to the DC IN jack and the AC plug of the
AC adaptor to the power outlet.
Notes
 AC adaptor is used as the main disconnect device, ensure that the
socket-outlet is located/installed near the equipment and is easily accessible.
 Use Only with specified Panasonic AC adaptor PQLV12Y.
Cable clamper
(included accessory)
Power Outlet
(AC 120V)
AC adaptor
(included accessory)
DC plugDC IN jack 
						

							Operating Instructions
22
3.Fix the AC adaptor cord with the cable clamper.
4.Turn on the PC connected to the KX-HGW600.
Note
Make sure the indicators light green ( Page 13).
AC adaptor cord
Thread the AC adaptor
cord through the cable clamper.
Close the cable clamper firmly. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 23
Setup
2.2.2 Setting up the KX-HGW600
Confirming the KX-HGW600 Setup
The KX-HGW600 has an integrated web server. If you can access the Camera Portal
page, the network configuration between the KX-HGW600 and the PC has been
successfully made.
1.Confirm the setup of the TCP/IP properties window on the PC.
For more information, please refer to Page 129.
2.Start up your web browser.
3.Enter http://192.168.0.254(:Port No.) in the address field of your web browser.
The Camera Portal page appears.
 When port no. is 80 (default setting), you do not need to enter port no.
If the Camera Portal page does not appear (Page 141)
Makesurehttp://192.168.0.254(:Port No.) has been correctly entered into
the address field.
 Make sure the indicators light green.
 Make sure the KX-HGW600 is turned on first, then the PC.
 The proxy server setting of your web browser may be needed to access the
Camera Portal page. For more information, please refer to Page 126.
4.Click[Setup Page].
The authentication window appears. 
						

							Operating Instructions
24
5.Enter KX-HGWinthePassworddata field.
Leave theUser Namedata field blank.
6.Click[OK].
The Basic Setup window appears.
Notes
 You can change the password on the Setup Page. Please refer to Change
PasswordonPage110.
 For more information about the Setup Page, please refer to Page 68. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 25
Setup
Setting up Internet Configuration
Depending on the ISP, you can connect the following four types of Internet configuration.
 DHCP Connection (Follow the steps from this page)
 Static Connection ( Page 27)
 PPPoE Connection ( Page 29)
 PPPoE Connection (IP unnumbered) ( Page 31)
DHCP Connection(using a DHCP server)
When the ISP provides you with DHCP Connection, follow the steps below.
1.Click[Basic Setup]on the Setup Page.
SELECTEDis displayed next to the configuration type which is currently
selected. (The default setting is DHCP Connection.)
2.Click[DHCP Connection].
Internet
The DHCP server of your
ISP assigns IP addresses
automatically.Modem
ISPPrivate IP address
192.168.0.113
Private IP address
192.168.0.114 Private IP address
192.168.0.1 
						

							Operating Instructions
26
3.EnterDevice Name,Gateway,DNS Server 1,DNS Server 2andDomain
Nameif requested by your ISP.
For each input value, please refer to the account information on Page 17.
 To clear the current settings, click[Clear].
Notes
 Donotenterthespaceineachdatafield.
 Some ISPs may call Device Name differently. Please ask your ISP about
Device Name.
4.When you have finished, click[Save]. The settings will be saved.
5.Click[Restart Now!].
Next, confirm the Internet Configuration ( Page 33). 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 27
Setup
Static Connection(using static IP address)
When the ISP provides you with Static Connection, follow the steps below.
1.Click[Basic Setup]on the Setup Page.
SELECTEDis displayed next to the configuration type which is currently
selected.
2.Click[Static Connection].
Modem
Static IP address
Your ISP assigns static
IP address based on the
account information.
Internet
ISP
Private IP address
192.168.0.113
Private IP address
192.168.0.114
Private IP address
192.168.0.1 
						

							Operating Instructions
28
3.EnterIP Address,Subnet Mask,Gateway,DNS Server 1andDNS Server 2.
If requested by your ISP, enterDomain Name. For each input value, please refer
to the account information on Page 17.
 To clear the current settings, click[Clear].
Note
Do not enter the space in each data field.
4.When you have finished, click[Save]. The settings will be saved.
5.Click[Restart Now!].
Next, confirm the Internet Setup ( Page 33). 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 29
Setup
PPPoE Connection(using a single global IP address)
When the ISP provides you with PPPoE Connection, follow the steps below.
1.Click[Basic Setup]on the Setup Page.
SELECTEDis displayed next to the configuration type which is currently
selected.
2.Click[PPPoE Connection].
Modem
Your ISP assigns a single
global IP address with
the PPPoE Connection.Private IP address
192.168.0.113
Private IP address
192.168.0.114 ISP
Private IP address
192.168.0.1 Internet 
						

							Operating Instructions
30
3.EnterUser NameandPassword.
If requested by your ISP, enterService Name,Access Concentrator Name
(sometimes specified as AC Name),DNS Server 1,DNS Server 2and
Domain Name.
For each input value, please refer to the account information on Page 17.
 To clear the current settings, click[Clear].
Note
Do not enter the space in each data field.
4.When you have finished, click[Save]. The settings will be saved.
5.Click[Restart Now!].
Next, confirm the Internet Configuration ( Page 33).