Panasonic Network Camera BL-C30A Getting Started Manual

							Operating Instructions
65[For assistance, please call: 1-800-272-7033]
4.Set the time, and click [Next>].
Note
The timer works by an internal clock. Set the date and time before using timer 
buffer/transfer (see page 40).
 Clicking [].
Note
If you enable the Lens Position When Triggered setting, buffer/transfer starts 
after the camera turns to the sensor position.
 Clicking [
						

							Operating Instructions
66
6.Set the image settings, and click [Next>].
 Clicking [
						

							Operating Instructions
67[For assistance, please call: 1-800-272-7033]
7.Set the image buffer frequencies and sensor deactivation time, and click 
[Next>].
 Clicking [
						

							Operating Instructions
68
Sensor 
deactivation 
time Set the length of time during which the sensor cannot be 
triggered after saving images temporarily or transmitting 
them. This function is recommended to use not to send too 
many E-mails to a mobile phone.
Note
The internal memory cannot buffer images during Sensor 
deactivation time. Because of this, images taken before 
detection are not saved in internal memory, and so cannot 
be received. Depending on the settings for image buffer/
transfer, even if it is set to, for example, take 1 image per 
second, and store 10 images, before detection, because 
the images are not stored in internal memory, if the sensor 
detects something directly after the end of Sensor 
deactivation time, the images may not be saved. Ten 
seconds after the end of Sensor deactivation time, images 
can be received as specified in the settings. Setting Description 
						

							Operating Instructions
69[For assistance, please call: 1-800-272-7033]
8.Select the transfer method, and click [Next>].
 Clicking [
						

							Operating Instructions
70
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions
71[For assistance, please call: 1-800-272-7033] When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions
72
9.After you confirm the settings and click [Next>], set E-mail notification and click 
[Next>].
 If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings seeing page 71 and page 72. When finished, 
click [Next>] and go to step 10.
10.Click [Save] after confirming the settings.
 New settings are saved. The buffered images are deleted.
 When finished, Success! is displayed. Subject
*2 Enter a subject with ASCII characters (see page 107) or 
characters in each language (0—44 characters for a 1-byte 
character and 0—22 characters for a 2-byte character).
Text  Enter text with ASCII characters (see page 107) or 
characters in each language (0—63 characters for a 1-byte 
character and 0—31 characters for a 2-byte character). But 
[] and [end-of-line] key are not available.
*1But [Space], [], [], [&], [] are not available.*2But [] is not available.
Setting Description
Disable  The camera does not send an E-mail notification when 
buffering or transferring image.
Enable  The camera sends an E-mail notification (up to 3 
destinations) when buffering or transferring image. Setting Description 
						

							Operating Instructions
73[For assistance, please call: 1-800-272-7033]
11.Click [Go to Image Buffer/Transfer page].
 The Image Buffer/Transfer page is displayed.
Notes
 If you set a short interval to transfer image to a mobile phone, many E-
mails may be sent to it leading to a large phone bill. Therefore, we 
recommend you to set a long interval. In an emergency situation, the E-
mail transfer can be stopped by enabling privacy mode using a mobile 
phone (see page 26).
 Sensor transfer stops its operations until the camera finishes all transfers. 
For example, if the camera transfers 3 images per minute and 6 images in 
total with setting 1 minute of sensor deactivation time, the sensor will be 
in the following operation.
 Buffered images will be deleted by doing the following.
 Turning off the camera.
 Saving the settings of Image Buffer/Transfer or Date and Time.
 Executing [Restart], [Update Firmware] or [Reset to Factory Default].
 Clicking [Delete Buffered Images] on the Image Buffer/Transfer page 
(see page 64).
Detectable UndetectableUndetectable 1st 2nd 3rd 4th 5th 6th120 seconds
A heat change occurs.
Detectable Sensor 
deactivation 
time
1 minute 
						

							Operating Instructions
74
2.15 Specifying Operation Time
The Operation Time page allows you to limit the operation time. The camera image 
turns to a gray screen outside the operation time.
Notes
 If you wrongly set the time period, your privacy may be seen. Confirm the 
time period after the setup.
 If you access the camera as an administrator, you can view the image 
outside the time period.
1.Click [Operation Time] on the Setup page.
2.Click [No.] to set the operation time.
Note
If No. 1—7 are disabled, the camera can always be operated.
3.Check [Enable], set the time, and click [Save] 
 Clicking [Cancel] takes you back to the previous page without saving 
changes.
Setting Description
Enable  Check the box to enable the setting. Clear the box to 
disable it.
A day of the 
week Check the box to enable the day. Clear the box to disable it.