Panasonic Network Camera BL-C30A Getting Started Manual

							Operating Instructions
75[For assistance, please call: 1-800-272-7033]
4.Click [Save] when finished.
 New settings are saved.
 The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday.Operation  Time  Select the [Always] option when you do not specify the time 
period. If you specify the time period, select the time period 
option and set the time period. Setting Description 
						

							Operating Instructions
76
2.16 Changing Indicator Display
The Indicator Control page allows you to select Indicator operation. Indicator has 
four options.
Always on
 Turn the indicator on when the camera is accessed.
 Turn the indicator on during sensor reaction.
 Always off
1.Click [Indicator Control] on the Setup page.
2.Select indicator option.
 Clicking [Cancel] cancels your settings without saving changes.
Notes
 See page 7 in the Installation/Troubleshooting for indicator display.
 Selecting [Never turn indicator on] keeps indicator always off.
3.Click [Save] when finished.
 New settings are saved.
 When finished, Success! is displayed. 
4.Click [Go to Indicator Control page].
 The Indicator Control page is displayed. 
						

							Operating Instructions
77[For assistance, please call: 1-800-272-7033]
2.17 Enabling Privacy Mode
Pressing the privacy button turns the camera into privacy mode. You can keep your 
privacy in privacy mode. In this case, the camera operation stops, and the image 
transfer by timer or sensor (see page 57 or page 64) is also stopped. The indicator 
turns red, and viewers see a gray screen. Privacy mode can be controlled from a 
mobile phone (see page 25) or a PC.
1.Click [Privacy Mode] on the Setup page.
2.Click [Save] when finished.
 Selecting [Enable] and clicking [Save] turn the camera into privacy mode.
Notes
 To turn the camera into normal operation, press the privacy button on the 
front of the camera (see page 7 in the Installation/Troubleshooting) during 
privacy mode. Or click [Disable Privacy Mode] after you log in as an 
administrator.
 If you log in as an administrator, you can disable privacy mode from your 
mobile phone (see page 25). Setting Description
Privacy  Button  Clearing the Enable box disables the privacy button on the 
front of the camera.
Privacy  Mode  Selecting [Enable] and clicking [Save] turn the camera into 
privacy mode. 
						

							Operating Instructions
78
3 Camera Maintenance
3.1 Maintenance page
Maintenance
(15) StatusDisplays the camera settings and status (see page 79).
(16) Wireless StatusDisplays wireless information (see page 79).
(17) RestartRestarts the camera (see page 80).
(18) Update FirmwareUpdates the camera firmware (see page 81).
(19) Save SettingsCreates a configuration file (see page 84).
(20) Load SettingsLoads settings from a configuration file (see page 85).
(21) Reset to Factory 
DefaultResets the camera to its default settings (see page 86).
(15)
(16)
(17)
(18)
(19)
(20)
(21) 
						

							Operating Instructions
79[For assistance, please call: 1-800-272-7033]
3.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
See Panasonic Network Camera support website at http://panasonic.co.jp/
pcc/products/en/netwkcam/ for details about status information.
3.1.2 Confirming the Wireless Status
The Wireless Status page allows you to check the wireless information. The 
wireless status information provides support for troubleshooting regarding wireless 
connection.
Clicking [Wireless Status] displays the following page. 
						

							Operating Instructions
80
3.1.3 Restarting the Camera
The camera restarts by disconnecting the plug of the AC cord from the outlet and 
reconnecting it again. The camera can also be restarted on the Restart page. 
Note
When the camera restarts, the buffered images will be deleted.
1.Click [Restart] on the Maintenance page.
2.Click [Restart].
 Restarting takes about 90 seconds. The Top page is displayed when 
finished. 
						

							Operating Instructions
81[For assistance, please call: 1-800-272-7033]
3.1.4 Updating the Camera Firmware
The Update Firmware page allows you to update the camera firmware. If the new 
firmware is available, install it into the camera.
Notes
 Do not turn off the power during firmware update.
 All buffered images will be deleted after the firmware update.
 The firmware version is displayed on the Top page and the Status page.
1.Download the new firmware on the Panasonic Network Camera support 
website at http://panasonic.co.jp/pcc/products/en/netwkcam/, and save it 
on your PC.
2.Click [Update Firmware] on the Maintenance page.
3.Click [Update Firmware].
 The camera restarts. 
						

							Operating Instructions
82
 The Update page is displayed in about 90 seconds.
4.Click [Browse...].
 A dialog box is displayed to select the firmware.
5.Select the firmware (including directory information) and click [Open].
 The firmware file name is displayed.
6.Confirm the firmware file name, and click [Update Firmware].
 Clicking [Cancel] takes you back to the Top page without firmware update.
 The next message is displayed during update.
 The camera restarts automatically after update.
 The Top page is displayed in about 90 seconds. 
						

							Operating Instructions
83[For assistance, please call: 1-800-272-7033]
7.Confirm that the version number on the Top page is updated.
 If the version number is updated, the firmware update is complete.
Updated version 
						

							Operating Instructions
84
3.1.5 Creating Configuration File
A configuration file can be saved on your PC. You can load the camera settings 
from the configuration file on the Load Settings page (see page 85).
1.Click [Save Settings] on the Maintenance page.
2.Click [Save].
3.Click [Save] on the File Download dialog box.
4.Specify the location, and click [Save] on the Save As dialog box.
 The configuration file is saved in the location.
Notes
 The file extension (.dat) cannot be changed. If you change it, the settings 
cannot be loaded.
 If you try to updating the camera, create a configuration file after updating 
the firmware. If there is a firmware version difference between the camera 
that you create a configuration file from and the camera that you try to load 
settings to, the settings may not be loaded to the camera.