Panasonic Network Camera BL-C30A Getting Started Manual

							Operating Instructions
55[For assistance, please call: 1-800-272-7033]
2.12 Configuring Multiple Cameras
The Multi-Camera Setup page allows you to configure the camera IP addresses 
and camera names to view multiple images on the Multi-Camera page (maximum 
12 cameras). These configurations are required to use the Multi-Camera page.
1.Click [Multi-Camera] on the Setup page.
2.Click [Add].
Notes
 If you click the camera number, the modification page is displayed. The 
camera setting can be modified or deleted on it.
 If you configured multiple cameras, you can change the camera number. 
Select the number, and click [Move].
3.Set each parameter.
 Clicking [Cancel] cancels your settings without saving changes. 
						

							Operating Instructions
56
Notes
 If your camera will only be accessed on your local network, use each 
cameras local IP address and port number.
 If you intend to access your camera from the Internet, you must use each 
cameras global IP address and respective port number.
4.Click [Save] when finished.
 New settings are saved.
 The Multi-Camera Setup page is displayed.Setting Description
Display  Check the box to enable the camera.
IP Address
*1 or 
Host Name*2 Set the IP address or the host name to enable the camera.
Port No.  Set the port number (1—65535).
Camera Name
*3 This camera name is displayed only on the Multi-Camera 
page.
*1Set 4 digits (0—255) and 3 periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available.
*2Enter ASCII characters for the host name (see page 107). But [Space], [], [], 
[#], [&], [%], [=], [+], [?], [] are not available.
Enter 1—255 characters.
*3Enter ASCII characters (see page 107) or characters in each language (1—15 
characters for a 1-byte character and 1—7 characters for a 2-byte character). 
But [Space], [], [], [#], [&], [%], [=], [+], [?], [:], [] are not available. 
						

							Operating Instructions
57[For assistance, please call: 1-800-272-7033]
2.13 Buffering or Transferring Images by Timer
The Image Buffer/Transfer page allows you to enable image buffer/transfer by E-
mail or FTP.
1.Click [Buffer/Transfer] on the Setup page.
2.Click [No.] to enable buffer/transfer.
3.Check [Enable Image Buffer/Transfer], select [Timer] for trigger, and click 
[Next>].
 Click [Delete Buffered Images] to delete this buffered images.
 Click [Save] to save the settings. The buffered images are deleted.
 Clicking [Cancel] takes you back to the Image Buffer/Transfer page without 
saving changes.
Setting Description
Enable Image 
Buffer/Transfer Check the box to enable the buffer/transfer. Clear the box 
to disable it.
Trigger  Selecting [Timer] enables the camera to buffer/transfer the 
image by timer.
 Selecting [Sensor] enables the camera to buffer/transfer 
the image by sensor. 
						

							Operating Instructions
58
4.Set the time, and click [Next>].
Note
The timer works by an internal clock. Set the date and time before using timer 
buffer/transfer (see page 40).
 Clicking [].
 Clicking [
						

							Operating Instructions
59[For assistance, please call: 1-800-272-7033]
6.Set the image buffer frequencies, and click [Next>].
 Clicking [
						

							Operating Instructions
60
7.Select the transfer method, and click [Next>].
 Clicking [
						

							Operating Instructions
61[For assistance, please call: 1-800-272-7033] When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions
62
When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions
63[For assistance, please call: 1-800-272-7033]
8.Confirm the settings, and click [Save].
 New settings are saved. The buffered images are deleted.
 When finished, Success! is displayed.
9.Click [Go to Image Buffer/Transfer page].
 The Image Buffer/Transfer page is displayed.
Notes
 If you set a short interval to transfer image to a mobile phone, many E-
mails may be sent to it leading to a large phone bill. Therefore, we 
recommend you to set a long interval. In an emergency situation, the E-
mail transfer can be stopped by enabling privacy mode using a mobile 
phone (see page 26).
 Buffered images will be deleted by doing the following.
 Turning off the camera.
 Saving the settings of Image Buffer/Transfer or Date and Time.
 Executing [Restart], [Update Firmware] or [Reset to Factory Default].
 Clicking [Delete Buffered Images] on the Image Buffer/Transfer page 
(see page 57). Subject
*2 Enter a subject with ASCII characters (see page 107) or 
characters in each language (0—44 characters for a 1-byte 
character and 0—22 characters for a 2-byte character).
Text  Enter text with ASCII characters (see page 107) or 
characters in each language (0—63 characters for a 1-byte 
character and 0—31 characters for a 2-byte character). But 
[] and [end-of-line] key are not available.
*1But [Space], [], [], [&], [] are not available.*2But [] is not available.
Setting Description 
						

							Operating Instructions
64
2.14 Buffering or Transferring Images by Sensor
The Image Buffer/Transfer page allows you to enable image buffer/transfer by E-
mail or FTP.
1.Click [Buffer/Transfer] on the Setup page.
2.Click [No.] to enable buffer/transfer.
3.Check [Enable Image Buffer/Transfer], select [Sensor] for trigger, and click 
[Next>].
 Click [Delete Buffered Images] to delete this buffered images.
 Click [Save] to save the settings. The buffered images are deleted.
 Clicking [Cancel] takes you back to the Image Buffer/Transfer page without 
saving changes.
Setting Description
Enable Image 
Buffer/Transfer Check the box to enable the buffer/transfer. Clear the box 
to disable it.
Trigger  Selecting [Timer] enables the camera to buffer/transfer the 
image by timer.
 Selecting [Sensor] enables the camera to buffer/transfer 
the image by sensor.