Panasonic Multi-Function Printer Kx Mb2060 Kx Mb2061 Operating Instructions

2.1 Connections
2.1.1 Base unit
Caution:
R When you operate this product, the power outlet
should be near the product and easily accessible.
Important:
R See page 18 to connect the handset unit.
Power cord
R Connect to a power outlet
(120 V, 60 Hz).
Telephone line cord
R Connect to a single telephone line jack (RJ11C).
To the Internet
Network router/Network hub (not supplied)
R Also connect networked computers.
LAN cable (not supplied)
R To assure continued emission limit compliance,
use only shielded...

Screws (not supplied)
R The charger can be mounted on the wall, if
required.
Caution:
R USE ONLY WITH the supplied Panasonic AC
adaptor.
R The AC adaptor must remain connected at all
times. (It is normal for the adaptor to feel warm
during use.)
R The AC adaptor should be connected to a
vertically oriented or floor -mounted AC outlet. Do
not connect the AC adaptor to a ceiling -mounted
AC outlet, as the weight of the adaptor may cause
it to become disconnected.
R Press the AC adaptor plug firmly.
2.2...

RThe battery level may not be displayed correctly after
you replace the batteries. In this case, place the
cordless handset on the charger and let it charge for
at least 7 hours.
2.3 Intelligent eco mode
(KX-MB2060 optional)
This feature automatically reduces cordless handset
power consumption by suppressing cordless handset
transmission power when the cordless handset is close
to the base unit.
R When this feature is activated, 
 is displayed.
2.4 Turning the power ON
Turn the power switch to the ON...

2.5 Dialing mode for the base unit,
and cordless handset
(KX-MB2060 optional)
If you cannot dial (page 49, 57), change this setting
according to your telephone line service.
1 MMenu N
2 Press  MB NM1NM 2NM 0N to display  “DIALING MODE ”.
3 Press  M1 N or  M2 N to select the desired setting.
M 1 N “ PULSE ”: For rotary/pulse dial service.
M 2 N “ TONE ” (default): For tone dial service.
4 MSet N
5 Press  MMenu N to exit.
2.6 Selecting the operation mode
(Scan/Copy/Fax)
You can select the desired mode by...

2.7 Setting the original
2.7.1 Using the scanner glass
1Open the document cover ( A).
2 Place the document FACE DOWN on the scanner
glass ( B), aligning the top left of the document with
the corner where the 
 mark is positioned.
3 Close the document cover.
Note:
R Confirm that there are no documents in the automatic
document feeder.
R Place the original onto the scanner glass gently. To
avoid malfunction, do not press down too firmly.
R If the original is a thick book, do not close the
document cover.
R...

Minimum document size
Maximum document size
Effective scanning area
RShaded area will be scanned.
R When using the unit as a scanner (page 37,
40), the effective scanning length depends on
the selected paper size.
Document weight
R Single sheet:
60 g/m 2
 to 75 g/m 2
 (16 lb to 20 lb)
R Multiple sheets:
60 g/m 2
 to 75 g/m 2
 (16 lb to 20 lb)
2.8 Help function
The unit contains helpful information, which can be
printed for reference.
– “BASIC SETTINGS ”
– “FEATURE LIST ”
– “PHONEBOOK ”
– “TAM OPERATION...

2.9 Adjusting the volume
2.9.1 Base unit
Important:
R Before adjusting the volume, set the operation
mode to fax mode. If the  MFax N light is OFF, turn
it ON by pressing  MFax N.
Ringer volume
While the unit is idle,  press MC N or  MD N.
To turn the ringer OFF
Press  MC N repeatedly to display  “RINGER OFF= OK? ”.
A  M Set N
R The base unit will not ring for outside calls.
The base unit will ring at the low level for intercom
calls.
R To turn the ringer back ON, press  MD N.
Handset receiver volume...

2.10 Date and time
We recommend you to set the date and time. The other
party will receive your unit ’s date and time as the header
information.
2.10.1 With the base unit
1 MMenu N A  M B NM1NM 0NM 1N A  M Set N
2 Enter the current month/date/year by selecting 2
digits for each.
Example: August 3, 2010
M 0 NM 8N M 0 NM 3N M 1 NM 0N
3 Enter the current hour/minute by selecting 2 digits for
each.
Example: 10:15 PM (12 hour clock format)
1. M1 NM 0N M 1 NM 5N
2. Press  MG N repeatedly to select  “PM ”.
4...

2.11 Your logo
You can program your logo (name, company name, etc.)
so that it appears on the top of each page sent.
1 MMenu N A  M B NM1NM 0NM 2N A  M Set N
2 Enter your logo, up to 30 characters (see page 106
for character entry).  A M Set N
3 Press  MMenu N to exit.
To correct a mistake
Press  MF N or  ME N to move the cursor to the incorrect
character, and make the correction.
R To erase all characters, press and hold  MStop N.
2.12 Your fax number
You can program your fax number so that it appears...

2.13 Configuring the unit to
access the LAN
You can use printer, scanner, fax, telephone answering
machine features using a computer connected to the
LAN. To enable these features, you need to set the IP
address, subnet mask, and default gateway in the unit.
Important:
R Consult your network administrator when setting
the IP address, subnet mask, and default
gateway.
2.13.1 Setting up automatically with a DHCP
server
Your situation:
– When only one unit is connected to the LAN.
If your network...