Panasonic LCD Projector Pt Rz570 Operating Instructions

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 51
Adjusting the volume
Adjust the volume of audio output.
 button
1) Press the  button/ button on the remote control.
Increases the volume.
 Decreases the volume.
Note
 fThis operation can be also performed using  qw  on the control panel.
Using the freeze function
The projected image can be paused and audio can be turned off regardless of the playback of the external device.
 button
1) Press the  button.
 fThe image freezes and...

Chapter 3 Basic Operations — Operating with the remote control
52 - ENGLISH
Using the automatic setup function
The image position when the DVI-D/HDMI signal is input, or the resolution, clock phase, and image position when 
the analog RGB signal is input can be adjusted automatically . (Analog RGB signal is a signal structured with dots 
just like the computer signal.)
It is recommended to input an image with bright white borders at the edges and high-contrast black and white 
characters when the...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 53
 fRefer to the [POSITION] menu  →  [SCREEN ADJUSTMENT] (x   page   70) for details.
Switching the image aspect ratio
Switch the image aspect ratio according to the input.
 button
1) Press the  button.
 fThe setting will change each time you press the button.
Note
 f Refer to the [POSITION] menu  →  [ASPECT] (x   page   68) for details.
Using the P IN P function
Locate a separate, small sub screen in the main screen to project two...

Chapter 3 Basic Operations — Operating with the remote control
54 - ENGLISH
Using the status function
Display the status of the projector.
 button
1) Press the  button.
 fThe 

[STATUS] screen is displayed.
10000h
10000h / 10000h
1.00 / 1.00
1/3
31°C/87°F27°C/80°F31°C/87°F31°C/87°F31°C/87°F
1013hPa
MENUEXIT
CHANGEENTERSEND E-MAIL
SELF TEST
ATMOSPHERIC PRESSUREAUTO - FLOOR
NO ERRORSCOOLING CONDITION LIGHT TEMP. 2 LIGHT TEMP. 1 EXHAUST AIR TEMP. OPTICS MODULE TEMP. INTAKE AIR TEMP. MAIN/SUB VERSION LIGHT...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 55
 fThe ID number set on the remote control will be stored unless it is set again. However , it will be erased if the remote control is left with dead 
batteries. Set the same ID number again when the batteries are replaced.
Note
 f When the ID number of the remote control is set to [0], you can control the projector regardless of the ID number setting of the projector 
body
, as same as when [ALL] is set.
 fSet the ID number of...

56 - ENGLISH
Chapter 4 Settings
This chapter describes the settings and adjustments you can make using the on-screen menu.  

Chapter 4 Settings — Menu navigation
ENGLISH - 57
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or control panel.
 fThe 

[MAIN MENU] screen is displayed.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
2) Press  as to select an...

Chapter 4 Settings — Menu navigation
58 - ENGLISH
4) Press as to select a sub-menu, and press qw or the  button to change or adjust settings.
 fSome items will switch in order as follows each time you press  qw

.
ABC
 fFor some items, press  qw to display an individual adjustment screen with a bar scale as shown below .
0CONTRAST
ADJUST
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu.
Same operation is available by pressing the  button.
 fSome items or...

Chapter 4 Settings — Menu navigation
ENGLISH - 59
Main menu itemPage
[DISPLAY LANGUAGE] 78
[DISPLAY OPTION]79
[PROJECTOR SETUP]95
[P IN P]11 2
[TEST PATTERN]11 4
[SIGNAL LIST]11 5
[SECURITY]11 8
[NETWORK]122
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu.
[PICTURE] 
Sub-menu itemFactory defaultPage
[PICTURE MODE] [GRAPHIC]
*162
[CONTRAST] [0]62
[BRIGHTNESS] [0]62
[COLOR] [0]
*263
[TINT] [0]63
[COLOR TEMPERATURE] [DEFAULT]
*263
[WHITE...

Chapter 4 Settings — Menu navigation
60 - ENGLISH
Sub-menu itemFactory defaultPage
[CLAMP POSITION] [24]
*174
[EDGE BLENDING] [OFF]74
[FRAME RESPONSE] [NORMAL]76
[RASTER POSITION] ―77
*1 Depends on the signal input.
Note
 fThe factory default setting varies depending on the selected input terminal.
[DISPLAY LANGUAGE] 
Details (x page 78)
[DISPLAY OPTION] 
Sub-menu item Factory defaultPage
[COLOR MATCHING] [OFF]79
[COLOR CORRECTION] [OFF]80
[SCREEN SETTING] ―80
[AUTO SIGNAL] [OFF]81
[AUTO SETUP] ―81...