Panasonic LCD Projector Pt Rz570 Operating Instructions

Chapter 2 Getting Started — Setting up
ENGLISH - 31
 rAngle sensor
The range of the installation attitude that is detected by the angle sensor built-in the projector is as follows.
30° 30°
Floor standing installation
Floor standing installation
Projection direction Ceiling mount installation
Parts for installation (optional)
The projector can be installed on the ceiling by combining the optional Ceiling Mount Bracket (Model No.: 
ET
-

PKD120H (for High Ceilings), ET
-
 PKD120S (for Low Ceilings)) and...

Chapter 2 Getting Started — Setting up
32 - ENGLISH
Attention
 fBefore setting up, read “Precautions for use” ( x   page   17). fDo not use the projector and the high-powered laser equipment in the same room.  The DLP
 chips can be damaged if a laser beam hits the 
projection lens surface.
[SCREEN ADJUSTMENT] projection range
[VERTICAL KEYSTONE] (viewed from the side) [HORIZONTAL KEYSTONE] (viewed from above)
ScreenScreen
Vertical arc correction (viewed from the side) Horizontal arc correction (viewed...

Chapter 2 Getting Started — Setting up
ENGLISH - 33
Projection distance
A ±5 % error in listed projection distances may occur.
When [SCREEN  ADJUSTMENT] is used, distance is corrected to become smaller than the specified image size. (Unit: m)
Projected image size Aspect ratio 16:10
Aspect ratio 16:9Aspect ratio 4:3
Projection distance 
(L) Height 
position (H) Projection distance 
(L) Height 
position (H) Projection distance 
(L) Height 
position (H)
Diagonal (SD) Min.
(LW) Max.
(LT) Min.
(LW) Max.
(LT)...

Chapter 2 Getting Started — Connecting
34 - ENGLISH
Connecting
Before connecting
 fBefore connecting, carefully read the operating instructions for the external device to be connected.
 fT

urn off the power of all devices before connecting cables.
 fT

ake note of the following points before connecting the cables. Failure to do so may result in malfunctions.
 g When connecting a cable to a device connected to the projector or the projector itself, touch any nearby 
metallic objects to eliminate static...

Chapter 2 Getting Started — Connecting
ENGLISH - 35
 terminal pin assignments and signal names
Outside viewPin No.Signal name Pin No.Signal name
(17)
(24)
(16)
(9)
(1)
(8)
(1) T.M.D.S data 2-(13) ―
(2) T.M.D.S data 2+ (14)+5
  V
(3) T.M.D.S data 2/4 shield (15)GND
(4) ―(16)Hot plug detection
(5) ―(17)T.M.D.S data 0
-
(6) DDC clock (18)T.M.D.S data 0+
(7) DDC data (19)T.M.D.S data 0/5 shield
(8) ―(20) ―
(9) T.M.D.S data 1
-(21) ―
(10) T.M.D.S data 1+ (22)T.M.D.S clock shield
(11) T.M.D.S data 1/3 shield...

Chapter 2 Getting Started — Connecting
36 - ENGLISH
Connecting example: Computers
ComputerControl computer
Computer
Computer Control computer
Attention
 fWhen connecting the projector to a computer or an external device, use the power cord supplied with each device and commercially 
available shielded cables.
Note
 fSwitching of the setting in the [DISPLA Y OPTION] menu → [DVI-D IN] → [EDID SELECT] may be required depending on the connected 
external device when DVI - D is input.
 fFor the HDMI cable,...

Chapter 2 Getting Started — Connecting
ENGLISH - 37
Connecting example using DIGITAL LINK
Twisted-pair-cable transmitter based on the communication standard HDBaseTTM such as the optional DIGITAL 
LINK output supported device (Model No.: ET
-

YFB100G, ET
-

YFB200G) uses the twisted pair cable to transmit 
input images, audio, Ethernet, and serial control signal, and the projector can input such digital signal to the 
 terminal.
Blu-ray disc player HDMI cable
(commercially available)
Control computer*1...

Chapter 2 Getting Started — Connecting
38 - ENGLISH
 fFor twisted-pair-cable transmitters of other manufacturers of which the operation has been verified with the projector , visit the Panasonic 
website (http://panasonic.net/avc/projector/). Note that the verification for devices of other manufacturers has been made for the items set 
by Panasonic Corporation, and not all the operations have been verified. For operation or performance problems caused by the devices of 
other manufacturers, contact the...

ENGLISH - 39
Chapter 3 Basic Operations
This chapter describes basic operations to start with. 

Chapter 3 Basic Operations — Switching on/off the projector
40 - ENGLISH
Switching on/off the projector
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being 
removed easily.
Confirm that the  switch is on the  side before connecting the power cord.
Use the power cord matching with the power supply voltage and the shape of the outlet.
For details of power cord handling, refer to “Read this first!” (x page 5).
How to attach the...