Panasonic LCD Projector Pt Rz570 Operating Instructions

Chapter 1 Preparation — Precautions for use
ENGLISH - 21
 fDirecting a high-power laser beam onto the projection lens surface can damage the DLP  chips.
 rLight source
The light source of the projector uses lasers, and has the following characteristics.
 fDepending on the operating environment temperature, the luminance of the light source will decrease.
The higher the temperature becomes, the more the luminance of the light source decreases.
 fThe luminance of the light source will decrease by duration...

Chapter 1 Preparation — Precautions for use
22 - ENGLISH
Accessories
Make sure that the following accessories are provided with your projector. Numbers enclosed in <    > show the 
number of accessories.
Wireless remote control unit 
(N2QAYA000126)
Power cord 
(TXFSX01RXQZ)
(TXFSX01RXRZ)
(TXFSX01RWDZ)
(TXFSX02UTRZ)
CD-ROM 
(TXFQB02XKPZ)
AAA/R03 or AAA/LR03 battery 
(For remote control unit)
Attention
 f After unpacking the projector , discard the power cord cap and packaging material properly.
 fDo not...

Chapter 1 Preparation — Precautions for use
ENGLISH - 23
Contents of the supplied CD-ROM
The contents of the supplied CD-ROM are as follows.
Instruction/list (PDF) Operating Instructions – Functional ManualMulti Monitoring & Control Software Operating Instructions
Logo Transfer Software Operating Instructions
List of Compatible Device 
ModelsThis is a list of display models (projector or flat panel display) that 
are compatible with the software contained in the CD-ROM and 
their restrictions.
Software...

Chapter 1 Preparation — About your projector
24 - ENGLISH
About your projector
Remote control
1
2
5 4
6
7
815
17
18 16
9
10 3
124
11
13
14 22
23
19
20
21
Front
To p
Bottom
1 Power  button
Sets the projector to the state where the projector is turned 
off (standby mode) when the  switch on the 
projector is set to  and in projection mode.
Sets the projector to projection mode when the power is 
switched off (standby mode).
2
 
Remote control indicator
Blinks if any button in the remote control is...

Chapter 1 Preparation — About your projector
ENGLISH - 25
 fObserve the following instructions that are indicated on the caution label at the back of the remote control: gDo not use old battery with new one. gDo not use batteries other than the type specified. gBe sure the batteries are inserted properly

.
For other instructions, read the instructions related to batteries that are described in “Read this first!”.
Caution label at the back of the remote control
Note
 f When operating the remote control...

Chapter 1 Preparation — About your projector
26 - ENGLISH
Projector body
1 2 34
7 7
9
8
13
5612888
17 18
15
1491016
Front
Side
Rear
19811
Projection direction
Bottom
To p
1 Remote control signal receiver (front)
2  
Power indicator 
Indicates the status of the power.
3
 
Light source indicator 
Indicates the status of the light source.
4

 
T
 emperature indicator 
Indicates the internal temperature status.
5
 
Projection lens
6

 
Lens shift lever
Adjusts the projection position.
7

 
Adjustable feet...

Chapter 1 Preparation — About your projector
ENGLISH - 27
16 Security slot
This security slot is compatible with the Kensington security 
cables.
17
 
 switch
T

urns on/off the main power. 18
  terminal
Connect the supplied power cord.
19
 
Burglar hook port
Attaches a burglar prevention cable, etc.
Attention
 fDo not block the ventilation ports (intake and exhaust) of the projector .
 rControl panel
3
1
2
1 Power < v/b> button
Sets the projector to the state where the projector is turned 
off (standby...

Chapter 1 Preparation — Preparing the remote control
28 - ENGLISH
Preparing the remote control
Inserting and removing the batteries
(i)(ii)
Fig. 1
Fig. 2
1) Open the cover. (Fig. 1)
2)  
Insert the batteries and close the cover (insert the 
 m side first). (Fig. 2)
 fWhen removing the batteries, perform the steps in reverse order

.
When using the multiple projectors
When you use the multiple projectors together, you can operate all the projectors simultaneously or each projector 
individually using...

ENGLISH - 29
Chapter 2 Getting Started
This chapter describes things you need to do before using the projector such as the setup and connections. 

Chapter 2 Getting Started — Setting up
30 - ENGLISH
Setting up
Installation mode
The installation modes of the projector are as follows. Set [FRONT/REAR]/[FLOOR/CEILING] in the 
[PROJECTOR SETUP] menu → [PROJECTION METHOD] (x
  page   95) depending on the installation mode.
Setting on a desk/floor and projecting forward Setting on a desk/floor and projecting from rear
(Using the translucent screen)
Menu itemSetting value Menu itemSetting value
[FRONT/REAR] [FRONT][FRONT/REAR] [REAR]
[FLOOR/CEILING]...