Panasonic LCD Projector Pt Rz570 Operating Instructions

Chapter 3 Basic Operations — Switching on/off the projector
ENGLISH - 41
Indicator statusProjector status
Red Lit
The power is switched off. (standby mode)
Projection will start when the power <
v/b> button is pressed.
 fThe setting of the projector is as follows.
 gThe [PROJECT

OR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] 
is set to [OFF]
 g The [PROJECT

OR SETUP] menu → [AUDIO SETTING] → [IN STANDBY MODE] is 
set to [OFF]
 f The projector may not operate when the light source indicator  or the...

Chapter 3 Basic Operations — Switching on/off the projector
42 - ENGLISH
4) Press the power  button.
 fThe power indicator  lights in green and the image is soon projected on the screen.
Note
 f A warm-up period of up to approximately five minutes may be necessary until an image is displayed when the projector is switched on at 
around 0   °C (32   °F).
The temperature indicator  lights in red during the warm-up period. When the warm-up is completed, the temperature indicator 
 turns off and the...

Chapter 3 Basic Operations — Switching on/off the projector
ENGLISH - 43
Initial setting (installation setting)
Set [FRONT/REAR] and [FLOOR/CEILING] in [PROJECTION METHOD] depending on the installation mode. 
Refer to “Installation mode” (x
  page   30) for details.
After completed the initial setting, you can change the setting from the [PROJECT OR SETUP] menu → 
[PROJECTION METHOD].
1)
 
Press 
 qw to switch the setting.
2/6
ENTERSET CHANGE
Change the projection method (FRONT/REAR, 
FLOOR/CEILING) if...

Chapter 3 Basic Operations — Switching on/off the projector
44 - ENGLISH
Initial setting (screen setting)
Set the screen format (aspect ratio) and display position of the image.
After completed the initial setting, you can change the settings of each item from the [DISPLAY OPTION] menu → 
[SCREEN SETTING].
1)
 
Press 
 qw to switch the setting.
 fProceed to Step 

4) when [16:10] is selected.
16:104/6
SCREEN POSITION
Set as necessary for the screen in use.
INITIAL SETTING
SET CHANGESCREEN FORMAT
ENTER
2)...

Chapter 3 Basic Operations — Switching on/off the projector
ENGLISH - 45
Note
 fIn the factory default setting, the time zone of the projector is set to +09:00 (Japan and Korea Standard  T ime). Change the setting of the 
[PROJECTOR SETUP] menu → [DATE AND TIME]  → [TIME ZONE] to the time zone of the region where you use the projector .
Initial setting (date and time)
Set the local date and time. After completed the initial setting, you can change the setting from the [PROJECTOR 
SETUP] menu → [DATE AND...

Chapter 3 Basic Operations — Switching on/off the projector
46 - ENGLISH
5) Adjust the position of the projected image by operating the lens shift l\
ever.
6)  
If the input signal is the analog RGB signal or the DVI
 - D/HDMI signal, press the  
button.
7)
 
T
 urn the zoom ring to adjust the size of the projected image to match the\
 screen.
8)
 
Adjust the focus again with the focus ring.
9)

 
Adjust the zoom again with the zoom ring to adjust the size of the proje\
cted image to match the 
screen....

Chapter 3 Basic Operations — Projecting
ENGLISH - 47
Projecting
Check the external device connection (x   page   34) and the power cord connection (x   page   40), and turn on 
the power (x   page   41) to start projection. Select the image to project, and adjust appearance of the projected 
image.
Selecting the input signal
Remote control Control panel
The input of the image to project can be switched. Method to switch the input is as follows.
 fPress the input selection button on the remote control and...

Chapter 3 Basic Operations — Projecting
48 - ENGLISH
Switching the input by displaying the input selection screen
The input for projection can be selected by displaying the input selection screen using the  
button on the control panel.
1)
 
Press the  button on the control panel.
 fThe input selection screen is displayed.
INPUT SELECT
COMPUTER1
COMPUTER2
VIDEO
DVI-D
HDMI1
HDMI2
DIGITAL LINK
SELECT
SET
ENTER
2) Press  as to select the input for projection, and press the  button.
Note
 f The input can...

Chapter 3 Basic Operations — Projecting
ENGLISH - 49
5) Adjust the zoom and the focus. (Fig. 2)
 fAdjust the size of the projected image by turning the zoom ring.
 fAdjust the focus by turning the focus ring.
Note
 f It is recommended that images be projected continuously for at least 30 minutes before the focus is adjusted. fSince the projected image size will change when the focus ring is turned, fine adjust the projected image size again by turning the zoom 
ring.
 fPerform the [POSITION] menu  →...

Chapter 3 Basic Operations — Operating with the remote control
50 - ENGLISH
Operating with the remote control
Using the shutter function
If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible 
to turn off the image and audio temporarily.
 button
1) Press the  button.
 fThe image and audio disappear

.
2)
 
Press the  button again.
 fThe image and audio reappear

.
Note
 f The power indicator  will blink slowly in green while the shutter...