Panasonic LCD Projector Pt Rz570 Operating Instructions

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 91
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT LOGO] Displays the Panasonic logo.
[USER LOGO] Displays the image registered by the user.
[NONE] Disables the startup logo display.
Note
 fWhen [USER LOGO] is selected, the display of the startup logo will be kept for approximately 15 seconds. fT
o create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
 f If...

Chapter 4 Settings — [DISPLAY OPTION] menu
92 - ENGLISH
 fIn the following conditions, the setting of the [PICTURE] menu  →  [GAMMA] → [DEFAULT] is disabled and the same gamma mode as when 
[2.2] is set is applied.
 g When the levels of [WHITE], [RED], [GREEN], and [BLUE] are adjusted gWhen [PC CORRECTION] is set to [ON] fIf you need to switch the gamma mode to [1.8] or [2.0], first set the [PICTURE] menu  →

 [GAMMA].
[SHUTTER SETTING]
Set the operation of the shutter function.
Setting [FADE-IN] or...

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 93
[FREEZE]
The projected image is paused and audio is turned off regardless of the playback of the external device.
1) 
Press 
 as to select [FREEZE].
2)
 
Press the  button.
 fPress the  button to release.
Note
 f [FREEZE] is displayed on the screen when video is paused.
[WAVEFORM MONITOR]
Use the input signals from a connected external device to display in a waveform. Check whether video output 
(luminance) signal level is within the recommended...

Chapter 4 Settings — [DISPLAY OPTION] menu
94 - ENGLISH
3) Adjust white level.
 fAdjust the white level 100

  % of the video signal to the 100   % position of the waveform monitor using the 
[PICTURE] menu → [CONTRAST].
Adjusting red, green, and blue
1) Set [COLOR TEMPERA TURE] to [USER]. (x   page   63)
2)  
Select “Select line (red)” on the waveform monitor
 .
3)
 
Adjust dark red areas.
 fUse [RED] in [WHITE BALANCE LOW] to adjust the black level 0

  % of the video signal to the 0   % position 
of...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 95
[PROJECTOR SETUP] menu
On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   57) for the operation of the menu screen.
[PROJECTOR ID]
The projector has an ID number setting function that can be used when multiple projectors are used side by side 
to enable simultaneous control or individual control via a single remote control.
1)
 
Press 
 as to...

Chapter 4 Settings — [PROJECTOR SETUP] menu
96 - ENGLISH
[ECO MANAGEMENT]
Set the operation method of the projector.
Setting [OPERATING MODE]
1) Press as to select [ECO MANAGEMENT].
2)  
Press the  button.
 fThe 

[ECO MANAGEMENT] screen is displayed.
3)
 
Press 
 as to select [OPERATING MODE].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL] Set this item when high luminance is required. [LIGHT OUTPUT] is 100   %, and the estimated runtime 
is...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 97
2) Press the  button.
 fThe 

[ECO MANAGEMENT] screen is displayed.
3)
 
Press 
 as to select [AUTO POWER SAVE].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the auto power save setting.
[ON] Enables the auto power save setting.
5) Press as to select [AMBIENT LIGHT DETECTION] or [NO SIGNAL LIGHTS-OUT].
[AMBIENT LIGHT 
DETECTION] Adjusts the power of the light source in accordance with...

Chapter 4 Settings — [PROJECTOR SETUP] menu
98 - ENGLISH
2) Press the  button.
 fThe 

[ECO MANAGEMENT] screen is displayed.
3)
 
Press 
 as to select [STANDBY MODE].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL] Select this item when using the network function during standby.
[ECO] Select this item to reduce power consumption during standby.
 fProceed to Step  5) when [NORMAL] is selected.
5)
 
Press 
 as to select [QUICK STARTUP].
6)
 
Press 
 qw...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 99
[BRIGHTNESS CONTROL]
The projector is equipped with a brightness sensor to measure brightness and color of the light source, and 
corrects brightness and white balance of the projected image according to the changes in brightness and color of 
the light source.
By using this function while structuring the multi-display by combining the projected images from multiple 
projectors, the change in the brightness and white balance for the whole...

Chapter 4 Settings — [PROJECTOR SETUP] menu
100 - ENGLISH
7) Press as to select [LINK].
8)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Performs corrections by the brightness sensor on a single projector without synchronizing with the 
other projectors.
The duration that the constant brightness is kept will become longer by setting the value of [LIGHT
 
OUTPUT] smaller.
[GROUP A]
[GROUP B]
[GROUP C]
[GROUP D] Performs correction by the brightness sensor...