Panasonic LCD Projector Pt Rz570 Operating Instructions

							Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 51
Adjusting the volume
Adjust the volume of audio output.
 button
1) Press the  button/ button on the remote control.
Increases the volume.
 Decreases the volume.
Note
 fThis operation can be also performed using  qw  on the control panel.
Using the freeze function
The projected image can be paused and audio can be turned off regardless of the playback of the external device.
 button
1) Press the  button.
 fThe image freezes and audio is muted.
2)

 
Press the  button again.
 fFreezing of the image is canceled and audio is turned on.
Note
 f [FREEZE] is displayed on the screen when video is paused. fWhen freezing of the moving image is canceled, the image may disappear or be disrupted temporarily .
Using the on-screen display function
Turn off the on-screen display function (no display) when you do not wish the viewers to see the on-screen 
display, such as the menu or the input terminal name.
 button
1) Press the  button.
 fThe on-screen display disappears.
2)

 
Press the  button again.
 fThe on-screen display appears.
Note
 f If you press the  button on the control panel for at least three seconds while the on-screen display is of f (hidden), the on-screen 
display is turned on.  
						

							Chapter 3 Basic Operations — Operating with the remote control
52 - ENGLISH
Using the automatic setup function
The image position when the DVI-D/HDMI signal is input, or the resolution, clock phase, and image position when 
the analog RGB signal is input can be adjusted automatically . (Analog RGB signal is a signal structured with dots 
just like the computer signal.)
It is recommended to input an image with bright white borders at the edges and high-contrast black and white 
characters when the automatic adjustment is being performed.
Avoid using images that include halftones or gradation, such as photographs and computer graphics.
 button
1) Press the  button.
 f[COMPLETE] is displayed when it has completed without any problem.
Note
 f The clock phase may shift even if it has completed without any incident. In such a case, adjust the [POSITION] menu  →  [CLOCK PHASE] 
(x   page   70).
 fIf an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or adjustment may not be performed properly even 
when [COMPLETE] appears. In such a case, adjust the following settings.
 g[ADV

ANCED MENU] menu → [INPUT RESOLUTION] ( x
  page   74)
 g[POSITION] menu  →

 [CLOCK PHASE] (x   page   70)
 g[POSITION] menu  →

 [SHIFT] (x
  page   68)
 fAdjust special signals according to the [DISPLA

Y OPTION] menu → [AUTO SETUP] ( x
  page   81).
 fAutomatic adjustment may not be possible depending on the computer model. fAutomatic adjustment may not be possible for the synchronization signal for composite sync or SYNC ON GREEN.  fImage may be disrupted for a few seconds during automatic adjustment, but this is not a malfunction. fAdjustment is required for each input signal. fAutomatic adjustment can be canceled by pressing the  button during the automatic adjustment operation. fEven if a signal possible to perform the automatic setup is being input, it may not be able to adjust correctly if the automatic setup function 
is used while the moving image is being input. [INCOMPLETE] may be displayed, or the adjustment may not be completed correctly even if 
[COMPLETE] is displayed.
Using the screen adjustment function
The [SCREEN ADJUSTMENT] menu can be displayed.
Correct the distortion of the image that occurs when the projector is in\
stalled tilted or when the screen is tilted or 
curved.
 button
1) Press the  button.
 fThe 

[SCREEN ADJUSTMENT] screen is displayed.
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button. 
[OFF] Disables the screen adjustment function.
[KEYSTONE] Adjusts any trapezoidal distortion in the projected image. 
[CORNER CORRECTION] Adjusts any distortion in the four corners of the projected image.
[CURVED CORRECTION] Adjusts any curved distortion in the projected image.
 fThe items will also switch by pressing the  button.
 fProceed to Step 

3) when anything other than [OFF] is selected.
3)
 
Press the  button.
 f The 

[KEYSTONE] screen, the [CORNER CORRECTION] screen, or the [CURVED CORRECTION] screen 
is displayed.
Note
 f To adjust [KEYSTONE] or [CURVED CORRECTION], press as to select the item to adjust, and press qw to adjust the item. fT
o adjust [CORNER CORRECTION], press as to select the item to adjust. Individual adjustment screen is displayed by pressing the 
 button. Adjust the item using asqw .
 fOnly one of the [KEYST

ONE], [CORNER CORRECTION], or [CURVED CORRECTION] setting is enabled.  
						

							Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 53
 fRefer to the [POSITION] menu  →  [SCREEN ADJUSTMENT] (x   page   70) for details.
Switching the image aspect ratio
Switch the image aspect ratio according to the input.
 button
1) Press the  button.
 fThe setting will change each time you press the button.
Note
 f Refer to the [POSITION] menu  →  [ASPECT] (x   page   68) for details.
Using the P IN P function
Locate a separate, small sub screen in the main screen to project two images simultaneously .
 button
1) Press the  button.
 fThe setting will change each time you press the button.
Note
 f Refer to “[P  IN P] menu” (x   page   112) for details.
Using the function button
By assigning the following functions to the  button, it can be used as a simplified shortcut button.
[SUB MEMORY], [SYSTEM SELECTOR], [DAYLIGHT VIEW], [WAVEFORM MONITOR]
 button
1) Press the  button.
Note
 f Assignment of the function is performed from the [PROJECT OR SETUP] menu → [FUNCTION BUTTON] (x   page   106).
Displaying internal test pattern
The projector has eight types of internal test patterns to check the condition of the projector body. To display test 
patterns, perform the following steps.
 button
1) Press the  button.
2)  
Press 
 qw to select the test pattern.
Note
 f Test patterns can also be displayed using the menu operation. Refer to “[TEST PATTERN] menu” (x   page   114) for details. fSettings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing 
various adjustments.  
						

							Chapter 3 Basic Operations — Operating with the remote control
54 - ENGLISH
Using the status function
Display the status of the projector.
 button
1) Press the  button.
 fThe 

[STATUS] screen is displayed.
10000h
10000h / 10000h
1.00 / 1.00
1/3
31°C/87°F27°C/80°F31°C/87°F31°C/87°F31°C/87°F
1013hPa
MENUEXIT
CHANGEENTERSEND E-MAIL
SELF TEST
ATMOSPHERIC PRESSUREAUTO - FLOOR
NO ERRORSCOOLING CONDITION LIGHT TEMP. 2 LIGHT TEMP. 1 EXHAUST AIR TEMP. OPTICS MODULE TEMP. INTAKE AIR TEMP. MAIN/SUB VERSION LIGHT RUNTIME PROJECTOR RUNTIME PROJECTOR TYPE
STATUS
RZ570(123456789012)
Note
 f
The projector status can also be displayed using the menu operation. Refer to the [PROJECT OR SETUP] menu  → [STATUS] 
(x   page   108) for details.
Using the ECO management function
Display the setting screen relating to ECO management.
 button
1) Press the  button.
Note
 f Refer to the [PROJECT OR SETUP] menu → [ECO MANAGEMENT] ( x   page   96) for details.
Setting ID number of the remote control
When you use the multiple projectors together, you can operate all the projectors simultaneously or each projector 
individually using a single remote control, if a unique ID number is assigned to each projector .
After setting the ID number of the projector, set same ID number on the remote control.
The factory default ID number of the projector is set to [ALL]. When using a single projector , press the  button on the remote control. Also, you can control a projector by pressing the  button on 
the remote control even if you do not know the projector ID.
 button
1) Press the  button on the remote control.
2)  
W
 ithin five seconds, press and set the one-digit or two-digit ID number set on the projector body 
using the number ( - ) buttons.
 f If you press the  button, you can control the projectors regardless of the ID number setting of the 
projector body.
Attention
 f Since the ID number of the remote control can be set without the projector body , do not press the  button on the remote control 
carelessly . If the  button is pressed and no number ( - ) buttons are pressed within five seconds, the ID number returns to 
its original value before the  button was pressed.  
						

							Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 55
 fThe ID number set on the remote control will be stored unless it is set again. However , it will be erased if the remote control is left with dead 
batteries. Set the same ID number again when the batteries are replaced.
Note
 f When the ID number of the remote control is set to [0], you can control the projector regardless of the ID number setting of the projector 
body
, as same as when [ALL] is set.
 fSet the ID number of the projector body from the [PROJECT

OR SETUP] menu → [PROJECTOR ID].  
						

							56 - ENGLISH
Chapter 4 Settings
This chapter describes the settings and adjustments you can make using the on-screen menu.  
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 57
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or control panel.
 fThe 

[MAIN MENU] screen is displayed.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
2) Press  as to select an item from the main menu.
 fThe selected item is highlighted in yellow

.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
3) Press the  button.
 fThe sub-menu items of the selected main menu are displayed.
0
POSITION
SHIFT
ASPECT
ZOOM
CLOCK PHASE
SCREEN ADJUSTMENT
MENU SELECT
SUB MENU DEFAULTENTER   
						

							Chapter 4 Settings — Menu navigation
58 - ENGLISH
4) Press as to select a sub-menu, and press qw or the  button to change or adjust settings.
 fSome items will switch in order as follows each time you press  qw

.
ABC
 fFor some items, press  qw to display an individual adjustment screen with a bar scale as shown below .
0CONTRAST
ADJUST
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu.
Same operation is available by pressing the  button.
 fSome items or functions may not be adjusted or used for certain signals to be input to the projector . When the items cannot be adjusted or 
used, the items in the menu screen are shown in black characters, and they cannot be adjusted or set.
If the item in the menu screen is displayed in black characters and the item cannot be adjusted or set, the factor causing it is displayed by 
pressing the  button while the corresponding menu is selected.
 f Some items can be adjusted even if signals are not input. fIndividual adjustment screen is cleared automatically if no operation is performed for approximately five seconds. fFor menu items, refer to “Main menu” (

x   page   58) and “Sub-menu” (x
  page   59).
 fThe cursor color depends on the setting in the [DISPLA

Y OPTION] menu → [ON-SCREEN DISPLAY] → [OSD DESIGN]. The selected item 
is displayed with the yellow cursor by the factory default.
 f In the portrait setting, the on-screen menu is displayed sideways.
T

o display the on-screen menu vertically, change the setting of the [DISPLAY OPTION] menu  → [ON-SCREEN DISPLAY] → [OSD 
ROTATION].
Resetting adjustment values to the factory default
If the  button on the remote control is pressed, the values adjusted in the menu items are restored to 
the factory default settings.
 button
1) Press the  button on the remote control.
0CONTRAST
ADJUST
Note
 fYou cannot reset all the settings to the factory default at a time. fT
o reset all the settings adjusted in the sub-menu item to the factory default one at a time, execute the [PROJECT OR SETUP] menu → 
[INITIALIZE].
 f Some items cannot be reset to the factory default settings even when the  button on the remote control is pressed. Adjust those 
items individually.
 f The triangular mark 

under the bar scale in the individual adjustment screen indicates the factory default setting. The position of the triangular 
mark varies according to the selected input signals.
Current adjustment value
Factory default setting
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a sub-menu selection screen.
Main menu item Page
[PICTURE] 62
[POSITION]68
[ADVANCED MENU]73   
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 59
Main menu itemPage
[DISPLAY LANGUAGE] 78
[DISPLAY OPTION]79
[PROJECTOR SETUP]95
[P IN P]11 2
[TEST PATTERN]11 4
[SIGNAL LIST]11 5
[SECURITY]11 8
[NETWORK]122
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu.
[PICTURE] 
Sub-menu itemFactory defaultPage
[PICTURE MODE] [GRAPHIC]
*162
[CONTRAST] [0]62
[BRIGHTNESS] [0]62
[COLOR] [0]
*263
[TINT] [0]63
[COLOR TEMPERATURE] [DEFAULT]
*263
[WHITE GAIN] [+10]64
[GAMMA] [DEFAULT]65
[DAYLIGHT VIEW] [AUTO]
*265
[SHARPNESS] [+6]
*265
[NOISE REDUCTION] [OFF]
*266
[DYNAMIC CONTRAST] [OFF]
*266
[SYSTEM SELECTOR] [AUTO]
*166
*1 Depends on the signal input.
*2  Depends on the [PICTURE MODE].
[POSITION] 
Sub-menu item Factory defaultPage
[SHIFT] ―68
[ASPECT] [DEFAULT]
*168
[ZOOM] ―69
[CLOCK PHASE] [0]
*170
[SCREEN ADJUSTMENT] [OFF]70
*1 Depends on the signal input.
[ADVANCED MENU] 
Sub-menu item Factory defaultPage
[DIGITAL CINEMA REALITY] [AUTO]
*173
[BLANKING] ―73
[INPUT RESOLUTION] ―74   
						

							Chapter 4 Settings — Menu navigation
60 - ENGLISH
Sub-menu itemFactory defaultPage
[CLAMP POSITION] [24]
*174
[EDGE BLENDING] [OFF]74
[FRAME RESPONSE] [NORMAL]76
[RASTER POSITION] ―77
*1 Depends on the signal input.
Note
 fThe factory default setting varies depending on the selected input terminal.
[DISPLAY LANGUAGE] 
Details (x page 78)
[DISPLAY OPTION] 
Sub-menu item Factory defaultPage
[COLOR MATCHING] [OFF]79
[COLOR CORRECTION] [OFF]80
[SCREEN SETTING] ―80
[AUTO SIGNAL] [OFF]81
[AUTO SETUP] ―81
[COMPUTER IN/OUT] ―82
[DVI-D IN] ―84
[HDMI IN] ―85
[DIGITAL LINK IN] ―86
[ON-SCREEN DISPLAY] ―87
[CLOSED CAPTION SETTING] ―89
[BACK COLOR] [BLUE]90
[STARTUP LOGO] [DEFAULT LOGO]90
[UNIFORMITY] ―91
[SHUTTER SETTING] ―92
[FREEZE] ―93
[WAVEFORM MONITOR] [OFF]93
[CUT OFF] ―94
[PROJECTOR SETUP] 
Sub-menu item Factory defaultPage
[PROJECTOR ID] [ALL]95
[PROJECTION METHOD] ―95
[ECO MANAGEMENT] ―96
[BRIGHTNESS CONTROL] ―99
[SCHEDULE] [OFF]103
[INITIAL STARTUP] [LAST MEMORY]105
[STARTUP INPUT SELECT] [LAST USED]105
[RS-232C] ―106
[FUNCTION BUTTON] ―106
[AUDIO SETTING] ―107
[STATUS] ―108
[DATE AND TIME] ―109
[SAVE ALL USER DATA] ―11 0
[LOAD ALL USER DATA] ―11 0
[INITIALIZE] ―111
[SERVICE PASSWORD] ―111