Panasonic LCD Projector Pt Rz570 Operating Instructions

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 101
 fWhen the variation in brightness has increased due to aging of the light source, or when you replaced the light source, readjust the 
brightness control.
 fWhen the projector is used continuously for more than 24 hours, set [CALIBRA TION 

TIME]. If it is not set, correction will not be performed 
automatically.
 f The brightness control function and the dynamic contrast function will operate simultaneously , but the dynamic contrast function will not 
operate while measuring the brightness and the color

.
 fThe [CALIBRA

TION TIME] setting will be reflected when you enter the time.
 fThe [CALIBRA

TION MESSAGE] setting will be reflected at the time when the item is switched using  qw.
Displaying [BRIGHTNESS CONTROL STATUS]
Display the brightness control status.
1)
 
Press 
 as to select [BRIGHTNESS CONTROL].
2)
 
Press the  button.
 fThe 

[BRIGHTNESS CONTROL] screen is displayed.
3)
 
Press 
 as to select [BRIGHTNESS CONTROL STATUS].
4)
 
Press the  button.
 fThe 

[BRIGHTNESS CONTROL STATUS] screen is displayed.
[BRIGHTNESS CONTROL STATUS] screen display example
When [CONSTANT MODE] is set to [OFF]
The screen shows the status that the brightness control is disabled.
1
RETURN
BRIGHTNESS CONTROL STATUS
CONSTANT MODE PROJECTOR OFFMENU
When [CONSTANT MODE] is set to [AUTO], and [LINK] is set to [OFF]
The screen shows the status of the brightness control in one projector
.
5
1
6
RETURN
LINK
PROJECTOR OFF
BRIGHTNESS CONTROL STATUSMENU
When [CONSTANT MODE] is set to [AUTO], and [LINK] is set to [GROUP A] through [GROUP D]   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
102 - ENGLISH
The screen shows the status of the brightness control of synchronized projectors (up to eight units), including the 
projector being controlled through the on-screen menu.
2 1
3
4
5 
7
8
1:
2:
3:
4:
5:
6:
7:192. 168. 30.   2
192. 168. 30.   3
192. 168. 30.   4
LINK
UPDATE PROJECTOR
GROUP A
PROJECTOR2
PROJECTOR3
BRIGHTNESS CONTROL STATUS
MENU SELECT
When [CONSTANT MODE] is set to [PC]
5
1
6
RETURN
CONSTANT MODE
PROJECTOR PC
BRIGHTNESS CONTROL STATUSMENU
1 Display the name of the projector
.
2  
Display the synchronized group.
3

 
Display the IP
  address of the projector.
4
 
Display the names and IP
  addresses of projectors in same group detected over the network.
5
 
Display the status by color
 .
Green: There is an allowance for brightness correction.
Yellow: There is little allowance for brightness correction.
Red: There is a brightness control error.
6
 
Display error detailed messages.
7

 
Display error messages.
When the message [Failed to apply BRIGHTNESS CONTROL

 to some projectors.] appears, it means that synchronization with the 
projector displayed in red has failed.
Press as to select the projector displayed in red, and press the  button to display the error details.
8
 
Update to the latest status information.
 r Error details
Error message Measures to take
[Exceed maximum number of 
projectors.]
 f Limit the number of projectors in one group to eight.
 fT

o synchronize nine or more projectors, use a PC and the dedicated software “Multi Monitoring & 
Control Software”
*1.
[Please check the COMMAND 
CONTROL setting.]
 f Set [NETWORK CONTROL]  →

 [COMMAND CONTROL] to [ON] for the projector in error.
 fSet [NETWORK CONTROL]  →

 [COMMAND PORT] of all projectors to be linked to the same value.
[Please check the USER NAME 
and PASSWORD in the COMMAND 
CONTROL setting.]
 f Assign the same [User name] and [Password] strings that have web control administrator rights to 
all projectors to be linked.
[Cannot apply BRIGHTNESS 
CONTROL. Please check projector 
status.]
 f The projector is in standby

. Switch on the power.
[Brightness Sensor Error]
 f There is a problem with the brightness sensor

. If problems persist even after switching on the 
power, consult your dealer.
*1 “Multi Monitoring & Control Software” is included in the supplied CD-ROM.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 103
Note
 fIf the synchronized projectors are not displayed in the list, check the following: gAre there devices with the same IP
 address on the network?
 gAre LAN cables connected correctly? ( x

  page   127)
 gAre the subnets of the projectors the same? gAre the same [LINK] settings applied to a group? fRefer to [NETWORK SETUP] ( x

  page   123) or “[Network config] page” (x
  page   137) on how to change the projector name.
Brightness control adjustment procedure example
The steps exemplify an adjustment to link the brightness of eight projectors connected in a network.
1) 
Connect all projectors to the hub using LAN cables. ( x

  page   127)
2)
 
Switch on all projectors and start projection.
3)

 
Set [CONST
 ANT MODE] of [BRIGHTNESS CONTROL SETUP] to [OFF], and select [APPLY], and then 
press the  button.
4)
 
Set [OPERA
 TING MODE] of each projector to the same setting. ( x
  page   96)
5)
 
Set [SUBNET MASK] and [IP
  ADDRESS] in each projector.
 fT

o be able to communicate over the network, set the same value in [SUBNET  MASK] for all projectors and 
set a different value in [IP ADDRESS] for each projector.
6)
 
W
 ait for at least eight minutes after projection has started until the li\
ght source brightness becomes 
steady.
7)
 
Set all items in the [PICTURE] menu of all projectors to the same values\
.
8)

 
Adjust [COLOR MA
 TCHING] to match colors.
9)
 
Display the internal test pattern “All white” in all projectors.
10)

 
Set [BRIGHTNESS CONTROL
  GAIN] of all the projectors to 100   %.
11)
 
Set [BRIGHTNESS CONTROL
  GAIN] of the projector with the least brightness to 90   %.
12)
 
Adjust [BRIGHTNESS CONTROL
  GAIN] of each projector.
 fAdjust [BRIGHTNESS CONTROL

 GAIN] of all the other projectors so that the brightness will be the same 
as the projector with the least brightness.
13)
 
Set [CONST
 ANT MODE] of [BRIGHTNESS CONTROL SETUP] to [AUTO], and [LINK] to [GROUP A] in 
all projectors.
14)
 
Select [APPL
 Y] of [BRIGHTNESS CONTROL SETUP] and press the  button in all projectors.
 fBrightness control starts.
Note
 f Brightness is automatically corrected whenever the light source lights up by switching on/of f the projector , etc. fWhen the variation in brightness has increased due to aging of the light source, or when you replaced the light source, readjust the 
brightness control.
[SCHEDULE]
Set the command execution schedule for each day of the week.
Enabling/disabling the schedule function
1) Press  as to select [SCHEDULE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the schedule function.
[ON] Enables the schedule function. Refer to “How to assign a program” (
x
  page   104) or “How to set a 
program” (x
  page   104) for how to set the schedule.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
104 - ENGLISH
Note
 fThe [STANDBY MODE] setting will be forced to [NORMAL] when the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY 
MODE] is set to [ECO], and [SCHEDULE] is set to [ON]. Changing the setting to [ECO] is not available.  The [STANDBY MODE] setting will 
not change back even when [SCHEDULE] is set to [OFF] in this condition.
How to assign a program
1) Press  as to select [SCHEDULE].
2)  
Press 
 qw to select [ON], and press the  button.
 fThe 

[SCHEDULE] screen is displayed.
3)
 
Select and assign a program to each day of week.
 fPress 

as to select the day of week, and press qw to select a program number.
 fY

ou can set the program from No.1 to No.7. “ -   -   - ” indicates that the program number has not been set.
How to set a program
Set up to 16 commands to each program.
1) 
Press 
 as to select [SCHEDULE].
2)
 
Press 
 qw to select [ON], and press the  button.
 fThe 

[SCHEDULE] screen is displayed.
3)
 
Press 
 as to select [PROGRAM EDIT].
4)
 
Press 
 qw to select a program number, and press the  button.
5)
 
Press 
 as to select a command number, and press the  button.
 fY

ou can change the page using  qw.
6)
 
Press 
 asqw to select [TIME], and press the  button.
 fThe projector is in the adjustment mode (the time is blinking).
7)

 
Press 
 qw to select “hour” or “minute”, and press as or the number ( - ) buttons to set a 
time, and then press the  button.
8)
 
Press 
 asqw to select [COMMAND].
9)
 
Press the  button.
 fThe 

[COMMAND] detailed screen is displayed.
10)
 
Press 
 as to select a [COMMAND].
 fFor [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time 
you press 

qw.
 fWhen [INPUT] is selected, press the  button, and then press 

asqw to select the input to be 
set.
[COMMAND] Detailed settings of 
[COMMAND] Description
[POWER ON] ―Switches on the projector.
[STANDBY] ―Enters standby.
[QUICK STARTUP] [ON]
Enables the function of the [PROJECTOR SETUP] menu → [ECO 
MANAGEMENT] → [QUICK STARTUP].
[OFF] Disables the function of the [PROJECTOR SETUP] menu → [ECO 
MANAGEMENT] → [QUICK STARTUP].
[SHUTTER] [OPEN]
Disables the shutter function (shutter: open).
[CLOSE] Enables the shutter function (shutter: closed).   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 105
[COMMAND]Detailed settings of 
[COMMAND] Description
[INPUT] [COMPUTER1]
Switches the input to COMPUTER1.
[COMPUTER2]
*1Switches the input to COMPUTER2.
[VIDEO] Switches the input to VIDEO.
[DVI-D] Switches the input to DVI
- D.
[HDMI1] Switches the input to HDMI1.
[HDMI2] Switches the input to HDMI2.
[DIGITAL LINK] Switches the input to DIGITAL LINK.
[INPUT1] - [INPUT10]
*2Switches the input to DIGITAL LINK, and switches the input of the 
Panasonic twisted-pair-cable transmitter to the specified input.
[OPERATING MODE] [NORMAL]
Prioritizes luminance.
[ECO] Controls the power to increase the life of the light source although 
the luminance is lower than that of [NORMAL].
[SILENT] Prioritizes the operation with less noise although the luminance is 
lower than that of [NORMAL].
[USER] Controls the power with the setting set in [USER].
[P IN P] [OFF]
P IN P function is not used.
[USER1] Places the sub screen with the setting set in [USER1].
[USER2] Places the sub screen with the setting set in [USER2].
[USER3] Places the sub screen with the setting set in [USER3].
[IN STANDBY MODE(AUDIO)] [OFF]
Stops the audio output during standby.
[ON] Outputs the audio during standby.
[VOLUME] [0] - [63]Sets the volume.
*1 The [COMPUTER2] command is disabled when the [DISPLA Y OPTION] menu → [COMPUTER IN/OUT] → [COMPUTER2 SELECT] is set to 
[COMPUTER1 OUT].
*2
 
When the optional DIGIT
 AL LINK output supported device (Model No.: ET
-
 YFB100G, ET
-
 YFB200G) is connected to the projector, its input 
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
11) Press the  button.
 f The command is fixed and  n

 is displayed at the left of the selected command.
 fAfter the command is fixed, press the  button to close the detailed setting screen.
12)

 
Press 
 asqw to select [STORE], and press the  button.
Note
 f To delete a command that has been already set, press the  button on the remote control while the screen in Step  5) is 
displayed, or select [DELETE] at the screen in Step  6) and press the  button.
 fIf multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command 
number

.
 fThe operating time will be the local time. ( x

  page   109)
 fIf an operation is executed with the remote control or control panel of the projector or with a control command before the command set in 
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[INITIAL STARTUP]
Set the startup method when the  switch is set to .
1)
 
Press 
 as to select [INITIAL STARTUP].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[LAST MEMORY] Starts up the projector in the condition before the  switch is set to .
[STANDBY] Starts up the projector in standby.
[ON] Starts projecting immediately.
[STARTUP INPUT SELECT]
Set the input when the projector is switched on to start projection.
1)
 
Press 
 as to select [STARTUP INPUT SELECT].
2)
 
Press the  button.
 fThe 

[STARTUP INPUT SELECT]  screen is displayed.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
106 - ENGLISH
3) Press asqw to select the input, and press the  button.
[LAST USED] Keeps the input selected last.
[COMPUTER1] Sets the input to COMPUTER1.
[COMPUTER2] Sets the input to COMPUTER2.
[VIDEO] Sets the input to VIDEO.
[DVI-D] Sets the input to DVI
- D.
[HDMI1] Sets the input to HDMI1.
[HDMI2] Sets the input to HDMI2.
[DIGITAL LINK] Sets the input to DIGITAL LINK.
[INPUT1] - [INPUT10]
*1Sets the input to DIGITAL LINK, and switches the input of the Panasonic twisted-pair-cable 
transmitter to the specified input.
*1 When the optional DIGIT AL LINK output supported device (Model No.: ET- YFB100G, ET- YFB200G) is connected to the projector, its input 
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
[RS-232C]
Set the communication condition of the  terminal. Refer to “ terminal” (x page 163).
1)  
Press 
 as to select [RS-232C].
2)
 
Press the  button.
 fThe 

[RS-232C] screen is displayed.
3)
 
Press 
 as to select [INPUT SELECT].
4)
 
Press 
 qw to switch the item.
[PROJECTOR] Performs the RS - 232C communication with the  terminal of the projector.
[DIGITAL LINK] Performs the RS
- 232C communication via the optional DIGITAL LINK output supported device (Model 
No.: ET
-

YFB100G, ET
-
 YFB200G) and the  terminal.
5) Press as to select [BAUDRATE].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[9600]
Select the proper speed.
[19200]
[38400]
7) Press  as to select [PARITY].
8)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NONE]
Select the parity condition.
[EVEN]
[ODD]
Note
 f When [INPUT  SELECT] is set to [DIGITAL LINK], communication using that serial terminal is available only when the corresponding device 
(such as the optional DIGITAL LINK output supported device (Model No.: ET- YFB100G, ET- YFB200G)) is connected to the  terminal.
 f When transferring logos via the optional DIGIT

AL LINK output supported device (Model No.: ET
-
 YFB100G, ET
-
 YFB200G), setting for “NO 
SIGNAL SLEEP” of the DIGITAL LINK output supported device should be set to “OFF” to avoid interruption of communication.
 f The input communication speed is fixed to 9

  600   bps when [INPUT SELECT] is set to [DIGITAL LINK].
[FUNCTION BUTTON]
Set the function of the  button on the remote control.
1) 
Press 
 as to select [FUNCTION BUTTON].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 107
2) Press the  button.
 fThe 

[FUNCTION BUTTON] screen is displayed.
3)
 
Press 
 as to select a function.
[DISABLE] Disables the  button.
[SUB MEMORY] Displays the sub memory list. ( x
  page   117)
[SYSTEM SELECTOR] Switches the [SYSTEM SELECTOR] setting. (x
  page   66)
[DAYLIGHT VIEW] Switches the [DAYLIGHT VIEW] setting. ( x
  page   65)
[WAVEFORM MONITOR] Displays the waveform of the input signal. ( x
  page   93)
4) Press the  button.
[AUDIO SETTING]
Set audio functions in detail.
Adjusting the volume
1) Press as to select [AUDIO SETTING].
2)  
Press the  button.
 fThe 

[AUDIO SETTING]  screen is displayed.
3)
 
Press 
 as to select [VOLUME].
4)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Increases the volume.
0 - 63
Press q. Decreases the volume.
Adjusting the left to right audio balance
1) Press 
as to select [AUDIO SETTING].
2)  
Press the  button.
 fThe 

[AUDIO SETTING]  screen is displayed.
3)
 
Press 
 as to select [BALANCE].
4)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Increases the volume on the right.
L16 - R16
Press q. Decreases the volume on the left.
Setting audio output in the standby mode
1) Press 
as to select [AUDIO SETTING].
2)  
Press the  button.
 fThe 

[AUDIO SETTING]  screen is displayed.
3)
 
Press 
 as to select [IN STANDBY MODE].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Audio is not output during standby.
[ON] Audio is output during standby.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
108 - ENGLISH
Note
 fAudio is not output in the standby mode when the [PROJECT OR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to 
[ECO].
Setting audio output while using the shutter function
1) Press  as to select [AUDIO SETTING].
2)  
Press the  button.
 fThe 

[AUDIO SETTING]  screen is displayed.
3)
 
Press 
 as to select [IN SHUTTER].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Audio is not output while using the shutter function (shutter: closed).
[ON] Audio is output while using the shutter function (shutter: closed).
Setting mute mode
1) Press as to select [AUDIO SETTING].
2)  
Press the  button.
 fThe 

[AUDIO SETTING]  screen is displayed.
3)
 
Press 
 as to select [MUTE].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Audio is output.
[ON] Audio is not output.
Setting audio input from a connected device
1) Press as to select [AUDIO SETTING].
2)  
Press the  button.
 fThe 

[AUDIO SETTING]  screen is displayed.
3)
 
Press 
 as to select item to set in [AUDIO IN SELECT].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUDIO IN 1] Audio connected to the  terminal is output during projection of image from the set input 
terminal.
[AUDIO IN 2] Audio connected to the  terminal is output during projection of image from the set input 
terminal.
[AUDIO IN 3] Audio connected to the  terminal is output during projection of image from the set input 
terminal.
[HDMI1 AUDIO IN]
*1Audio input to HDMI1 is output.
[HDMI2 AUDIO IN]
*2Audio input to HDMI2 is output.
[DIGITAL LINK AUDIO IN]
*3Audio input to DIGITAL LINK is output.
*1 Only when the input signal is HDMI1
*2  
Only when the input signal is HDMI2
*3

 
Only when the input signal is DIGIT
 AL LINK
[STATUS]
Display the status of the projector.
1) 
Press 
 as to select [STATUS].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 109
2) Press the  button.
 fThe 

[STATUS] screen is displayed.
3)
 
Press 
 qw to switch the pages.
 fThe page will change each time you press the button.
[PROJECTOR TYPE] Displays the projector type and serial number of the projector.
[PROJECTOR RUNTIME] Displays the runtime of the projector.
[LIGHT RUNTIME] Displays the runtime of the light source.
[MAIN/SUB VERSION] Displays the main and sub versions of the firmware of the projector .
[INTAKE AIR TEMP.]
*1Displays the status of the intake air temperature of the projector.
[OPTICS MODULE TEMP.]
*1Displays the status of the internal temperature of the projector.
[EXHAUST AIR TEMP.]
*1Displays the status of the exhaust air temperature of the projector .
[LIGHT TEMP. 1]
*1Displays the temperature status for the front block of the light source (on the lens side).
[LIGHT TEMP. 2]
*1Displays the temperature status for the rear block of the light source (on the air exhaust port side).
[COOLING CONDITION] Displays the set cooling conditions.
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[SELF TEST] Displays the status of the projector.
[INPUT] Displays the input terminal currently selected.
[SIGNAL NAME] Displays the input signal name.
[MEMORY NO.] Displays the memory number of the input signal.
[ON COUNT] [POWER ON TIMES]Displays the number of times the power is turned on.
[NUMBER OF REGISTERED  SIGNAL] Displays the number of registered signals.
[SIGNAL INFORMATION] [INPUT]
Displays the input terminal used for the projected image.
[SIGNAL NAME] Displays the input signal name.
[SIGNAL FREQUENCY] Displays the frequency of the input signal.
[SYNC.STATE] Displays the sync polarity of the input signal.
[V.SYNC WIDTH] Displays the vertical sync signal pulse width of the input signal.
[SCAN TYPE] Displays the scan type of the input signal.
[TOTAL DOTS] Displays the total dot count of the input signal.
[DISPLAY DOTS] Displays the number of input signal display dots.
[TOTAL LINES] Displays the total line count of the input signal.
[DISPLAY LINES] Displays the number of input signal display lines.
[SAMPLING] Displays the sampling information of the input signal.
[SIGNAL LEVEL] Displays the signal level of the input signal.
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is 
green.
Note
 fE-mail containing the status can be sent to the E-mail address (up to two addresses) set in “[E-mail set up] page” ( x   page   139) by 
pressing the  button while the  [STATUS] screen is displayed.
 fThere may be items that are displayed and items that are not displayed in [SIGNAL  INFORMA

TION] depending on the setting or the input 
signal.
 f If any abnormality has occurred on the projector

, press the  button while the [STATUS] screen is displayed to display the detail 
screen of the error information.
 f For details on the contents displayed in [SELF 

TEST], refer to “[SELF TEST] indications” (x   page   153).
[DATE AND TIME]
Set the time zone, date, and time of the built-in clock of the projector.
Setting the time zone
1) Press as to select [DATE AND TIME].
2)  
Press the  button.
 fThe 

[DATE AND TIME] screen is displayed.
3)
 
Press 
 as to select [TIME ZONE].
4)
 
Press 
 qw to switch [TIME ZONE].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
110 - ENGLISH
Setting the date and time manually
1) Press as to select [DATE AND TIME].
2)  
Press the  button.
 fThe 

[DATE AND TIME] screen is displayed.
3)
 
Press 
 as to select [ADJUST CLOCK].
4)
 
Press the  button.
 fThe 

[ADJUST CLOCK] screen is displayed.
5)
 
Press 
 as to select an item, and press qw to set the local date and time.
6)
 
Press 
 as to select [APPLY], and press the  button.
 fThe setting of the date and time will be completed.
Setting the date and time automatically
1) Press  as to select [DATE AND TIME].
2)  
Press the  button.
 fThe 

[DATE AND TIME] screen is displayed.
3)
 
Press 
 as to select [ADJUST CLOCK].
4)
 
Press the  button.
 fThe 

[ADJUST CLOCK] screen is displayed.
5)
 
Press 
 as to select [NTP SYNCHRONIZATION], and press qw to change the setting to [ON].
6)
 
Press 
 as to select [APPLY], and press the  button.
 fThe setting of the date and time will be completed.
Note
 f To set the date and time automatically, the projector must be connected to the network. fIf synchronization with the NTP
 server fails just after [NTP SYNCHRONIZATION] is set to [ON], [NTP SYNCHRONIZATION] will return to 
[OFF]. If [NTP SYNCHRONIZATION] is set to [ON] while the NTP server is not set, [NTP SYNCHRONIZATION] will return to [OFF].
 f Access the projector via a web browser to set the NTP

 server. Refer to “[Adjust clock] page” (x   page   138) for details.
 fThe [TIME ZONE] setting is reset to the factory default when the [PROJECT OR SETUP] menu 

→ [INITIALIZE] → [ALL USER DATA] 
is executed. However, the date and time based on the local date and time setting (Coordinated Universal Time, UTC, Universal Time, 
Coordinated) will be maintained without being initialized.
[SAVE ALL USER DATA]
Save the various setting values as a backup in the built-in memory of the projector .
1)  
Press 
 as to select [SAVE ALL USER DATA].
2)
 
Press the  button.
 fThe 

[SECURITY PASSWORD] screen is displayed.
3)
 
Enter a security password and press the  button.
4)

 
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
 f[PROGRESS] is displayed while saving data.
Note
 f Data set from the computer application is not included in [ALL  USER DATA].
[LOAD ALL USER DATA]
Load the various setting values saved as a backup in the built-in memory of the projector .
1)  
Press 
 as to select [LOAD ALL USER DATA].