Panasonic LCD Projector Pt Rz570 Operating Instructions

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 111
2) Press the  button.
 fThe 

[SECURITY PASSWORD] screen is displayed.
3)
 
Enter a security password and press the  button.
4)

 
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f The projector enters the standby mode to reflect the setting values when [LOAD  ALL  USER DATA] is executed. fData registered from a computer is not included in [ALL
 USER DATA].
[INITIALIZE]
Return various setting values to their factory default settings.
1)
 
Press 
 as to select [INITIALIZE].
2)
 
Press the  button.
 fThe 

[SECURITY PASSWORD] screen is displayed.
3)
 
Enter a security password and press the  button.
 fThe 

[INITIALIZE]  screen is displayed.
4)
 
Press 
 as to select an item to initialize.
[ALL USER DATA] Returns all setting values including [REGISTERED SIGNAL], [NETWORK/E-MAIL], and [LOGO 
IMAGE] to the factory default settings.
The projector enters the standby mode to reflect the setting values.
[REGISTERED SIGNAL] Deletes all the setting values saved for each input signal.
To delete only a part of a registered signal, perform the procedure described in “Deleting the 
registered signal” (
x
  page   115).
[NETWORK/E-MAIL] Returns the setting of the [NETWORK] menu → [NETWORK SETUP] and the setting of “[E-mail set 
up] page” (x
  page   139) in the web control screen to the factory default settings.
[LOGO IMAGE] Deletes the image registered in [USER LOGO].
5) Press the  button.
6)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f The following settings are not initialized even if [ALL  USER DATA] is executed. gThe [DISPLA
Y OPTION] menu  → [UNIFORMITY]
 gThe [PROJECT

OR SETUP] menu → [ECO MANAGEMENT]  → [STANDBY MODE]
[SERVICE PASSWORD]
This function is used by a service person.   
						

							Chapter 4 Settings — [P IN P] menu
112 - ENGLISH
[P IN P] menu
On the menu screen, select [P IN P] from the main menu, and select an item from the sub-menu.
Refer to “Navigating through the menu” (x
  page   57) for the operation of the menu screen.
Using P IN P function
Locate a separate, small sub screen in the main screen to project two images simultaneously .
1)  
Press 
 as to select [P IN P MODE].
2)
 
Press the  button.
 fThe 

[P IN P MODE] screen is displayed.
3)
 
Press 
 as to select a function.
[OFF] P IN P function is not used.
[USER1]
The P IN P function is used with the setting set in “Setting P IN P function” (x
  page   112).
[USER2]
[USER3]
4) Press the  button.
Setting P IN P function
P IN P function settings can be saved to [USER1], [USER2], and [USER3].
1)
 
Press 
 as to select [P IN P MODE].
2)
 
Press the  button.
 fThe 

[P IN P MODE] screen is displayed.
3)
 
Press 
 as to select the desired mode from [USER1], [USER2], and [USER3], and press the  
button.
4)
 
Press 
 as to select [MAIN WINDOW] or [SUB WINDOW], and press the  button.
5)
 
Press 
 as to select the input terminal to be displayed in the window, and press the  button.
6)
 
Press 
 as to select an item.
[SIZE] Sets the window display size between 10   % and 100   %.
[POSITION] Sets the window display position within the screen.
[CLOCK PHASE] Sets the value between  0 and +31 when the sub window receives a signal from the  terminal or the  terminal and flickering image or smeared outline 
appears.
7) If [SIZE] is selected in Step 6), press the  button.
 f
The sub-menu is displayed.
8)

 
Press 
 as to select an item.
9)
 
Press 
 qw to make adjustment, and press the  button.
10)
 
If [POSITION] is selected in Step 6), press the  button.
1

1)  
Press 
 asqw to adjust the position, and press the  button.
12)
 
If [CLOCK PHASE] is selected in Step 6), press  qw

 to make adjustment.
13)
 
Press 
 as to select [FRAME LOCK].
14)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[MAIN WINDOW] Sets the frame lock for the input signal set in the main window.
[SUB WINDOW] Sets the frame lock for the input signal set in the sub window.   
						

							Chapter 4 Settings — [P IN P] menu
ENGLISH - 113
15) Press as to select [TYPE].
16)  
Press 
 qw to switch the item.
[MAIN WINDOW] The main window has display priority.
[SUB WINDOW] The sub window has display priority.
Note
 fThe P IN P function may not be available for some signals being input or terminals being selected. Refer to “Two-window display 
combination list” ( x
  page   166) for details.
 fThe main window setting values are applied as image adjustment values such as the [PICTURE] menu  →

 [PICTURE MODE]/[GAMMA]/
[COLOR TEMPERATURE].
 f While in the normal screen (where no menu is displayed), the sizes and positions of the main window and the sub window can be switched 
using 

as while P IN P is operating.
 f[P

 IN P] cannot be set when the [ADVANCED MENU] menu → [FRAME RESPONSE] is set to [FAST].   
						

							Chapter 4 Settings — [TEST PATTERN] menu
114 - ENGLISH
[TEST PATTERN] menu
On the menu screen, select [TEST PATTERN] from the main menu.
Refer to “Navigating through the menu” (x
  page   57) for the operation of the menu screen.
[TEST PATTERN]
Display the test pattern built-in to the projector.
Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input 
signal before performing various adjustments.
1)
 
Press 
 qw to switch the [TEST PATTERN] item.
 fThe items will switch each time you press the button.
Menu screen + All white
Displays a test pattern with the menu screen. Select a desired test pattern.
Menu screen + All black
Menu screen + Window
Menu screen + Window  (inversion)
Menu screen + Color bar  (vertical)
Menu screen + Color bar  (horizontal)
Menu screen + 16:9/4:3  aspect frame
Menu screen + Focus
Menu screen + Input screen Displays the menu screen and input signal.
Internal test patterns are not displayed.
Note
 f
Press the  button on the remote control while the test pattern is displayed to hide the menu screen.
Changing color or a focus test pattern
The color can be changed when the “Menu screen + Focus” test pattern is displayed.
1)
 
Press 
 qw to select the “Menu screen + Focus” test pattern.
2)
 
Press the  button.
 fThe 

[TEST PATTERN COLOR] screen is displayed.
3)
 
Press 
 as to select a color, and press the  button.
 fThe color of the focus test pattern will be changed to the selected color .
Note
 f The [TEST  PATTERN COLOR] setting returns to [WHITE] when the projector is switched off. fColors of the test patterns other than focus test patterns cannot be changed.   
						

							Chapter 4 Settings — [SIGNAL LIST] menu
ENGLISH - 115
[SIGNAL LIST] menu
On the menu screen, select [SIGNAL LIST] from the main menu.
Refer to “Navigating through the menu” (x
  page   57) for the operation of the menu screen.
 rRegistered signal details
A1 (1-2)
When the address number (A1, A2, ... L7, L8) signal is registered Sub memory number
Memory number:
 f
A name can be set for each sub memory (x   page   117).
Registering new signals
After a new signal is input and the  button on the remote control or the control panel is pressed, the 
registration is completed and the [MAIN MENU] screen is displayed.
Note
 f Up to 96 signals, including sub memories, can be registered to the projector . fThere are 12 pages (eight memories of 
A through L, with eight memories possible on each page) for memory numbers, and the signal is 
registered to the lowest number that is available. If there is no available memory number it will be overwritten from the oldest signal.
 f The name to be registered is automatically determined by the input signal. fIf a menu is being displayed, the new signals will be registered at the instant they are input.
Renaming the registered signal
Registered signals can be renamed.
1)
 
Press 
 asqw to select the signal of which name is to be changed.
2)
 
Press the  button.
 fThe 

[REGISTERED SIGNAL STATUS] screen is displayed.
 fThe memory number

, input terminal, input signal name, frequency, synch polarity, etc., are displayed.
 fPress the  button to return to the 

[SIGNAL LIST] screen.
3)
 
Press the  button.
 fThe 

[REGISTERED SIGNAL SETUP] screen is displayed.
4)
 
Press 
 as to select [SIGNAL NAME CHANGE].
5)
 
Press the  button.
 fThe 

[SIGNAL NAME CHANGE] screen is displayed.
6)
 
Press 
 asqw to select the text, and press the  button to enter the text.
7)
 
After the name is changed, press 
 asqw to select [OK], and press the  button.
 fThe registration is completed and the  [REGISTERED SIGNAL

 SETUP] screen returns.
 fWhen pressing  asqw to select [CANCEL] and pressing the  button, the changed signal name 
will not be registered and an automatically registered signal name will be used.
Deleting the registered signal
Registered signals can be deleted.
1)
 
Press 
 asqw to select the signal to delete.
2)
 
Press the  button on the remote control.
 fThe 

[REGISTERED SIGNAL DELETE] screen is displayed.
 fT

o cancel the deletion, press the  button to return to the  [REGISTERED SIGNAL LIST] screen.
3)
 
Press the  button.
 fThe selected signal will be deleted.   
						

							Chapter 4 Settings — [SIGNAL LIST] menu
116 - ENGLISH
Note
 fA registered signal can also be deleted from [REGISTERED SIGNAL DELETE] on the [REGISTERED SIGNAL SETUP] screen.
Protecting the registered signal
1) Press  asqw to select the signal to protect.
2)  
Press the  button.
 fThe 

[REGISTERED SIGNAL STATUS] screen is displayed.
3)
 
Press the  button.
 fThe 

[REGISTERED SIGNAL SETUP] screen is displayed.
4)
 
Press 
 as to select [LOCK].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] The signal is not protected.
[ON] The signal is protected.
 fA lock icon is displayed at the right of the  [SIGNAL LIST] screen when [LOCK] is set to [ON].
XXXXRGB2 RGB2A3: XGA75-A3 A1: 720/60p-A1A2: XXXXXX-A2
Note
 fWhen [LOCK] is set to [ON], signal deletion, image adjustment, and automatic setup are not available.  T o perform these operations, set 
[LOCK] to [OFF].
 f A

 signal can be registered to the sub memory even if it is protected.
 fEven a protected signal will be deleted if [INITIALIZE] is executed.
Expanding signal lock-in range
1) Press  asqw to select the signal to set.
2)  
Press the  button.
 fThe 

[REGISTERED SIGNAL STATUS] screen is displayed.
3)
 
Press the  button.
 fThe 

[REGISTERED SIGNAL SETUP] screen is displayed.
4)
 
Press 
 as to select [LOCK-IN RANGE].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NARROW] Select this item usually.
[WIDE] Widens the lock-in range.
 fAn expansion icon is displayed at the right of the  [SIGNAL  LIST] screen when [LOCK-IN RANGE] is set to 
[WIDE].
XXXXRGB2 RGB2A3: XGA75-A3 A1: 720/60p-A1A2: XXXXXX-A2
Note
 f Switch the range where the signal to be input is determined to be the same signal as the already registered signal. fT
o prioritize the determination that a signal is the same as the already registered signal, set this function to [WIDE].
 f Use in cases such as when the synchronizing frequency of a signal to be input has changed slightly , or multiple signal lists are registered. fThis function can be used only when a signal is input from the  terminal, the  terminal, the 
 terminal, the  terminal, the  terminal, or the  terminal.
 fWhen [WIDE] is set, the image may be distorted because a signal is recognized as the same even if its synchronizing frequency varies 
slightly

.
 fWhen a signal to be input corresponds to multiple signals set in [WIDE], a registered signal with a high memory number receives priority . 
Example: a signal to be input that corresponds to memory numbers  A2, 

A4 and B1 will be determined to be B1.
 fWhen a registration signal is deleted, the settings are also deleted.   
						

							Chapter 4 Settings — [SIGNAL LIST] menu
ENGLISH - 117
 fIn an environment where multiple types of signals are input to the same terminal, signals are sometimes not determined correctly when the 
setting is set to [WIDE].
Sub memory
The projector has a sub memory function that can register the multiple image adjustment data, even if it is 
recognized as the same signal by the frequency or format of the synchronization signal source.
Use this function when you need to switch the aspect or adjust the picture quality such as the white balance 
while using the same signal source. The sub memory includes all the data that can be adjusted for each signal, 
such as the image aspect ratio and data adjusted in the [PICTURE] menu (items such as [CONTRAST] and 
[BRIGHTNESS]).
Registering to the sub memory
1) While in the normal screen (where no menu is displayed), press  as .
 fThe sub memory registration screen is displayed if the sub memory is not registered. Proceed to Step  3)

.
 fA

 list of sub memories registered to the signal currently input is displayed.
 fThe  button on the remote control can be used instead of  as

 when [SUB MEMORY] is 
selected from the [PROJECTOR SETUP] menu → [FUNCTION BUTTON].
2)
 
Press 
 asqw to select the sub memory number to register in [SUB MEMORY LIST].
3)
 
Press the  button.
 fThe 

[SIGNAL NAME CHANGE] screen is displayed.
4)
 
Press 
 asqw to select [OK], and press the  button.
 fT

o rename the registered signal, follow the procedure in Steps  6) and 7) in “Renaming the registered signal” 
(x
  page   115).
Switching to the sub memory
1) While in the normal screen (where no menu is displayed), press  as .
 fA

 list of sub memories registered to the signal currently input is displayed.
2)
 
Press 
 asqw to select the signal to switch in [SUB MEMORY LIST].
3)
 
Press the  button.
 fThis switches to the signal selected in Step  2)

.
Deleting the sub memory
1) While in the normal screen (where no menu is displayed), press  as .
 fThe 

[SUB MEMORY LIST]  screen is displayed.
2)
 
Press 
 asqw to select the sub memory to be deleted, and press the  button on the 
remote control.
 f The 

[REGISTERED SIGNAL DELETE] screen is displayed.
 fT

o cancel the deletion, press the  button to return to the  [SUB MEMORY LIST] screen.
3)
 
Press the  button.
 fThe selected sub memory will be deleted.   
						

							Chapter 4 Settings — [SECURITY] menu
118 - ENGLISH
[SECURITY] menu
On the menu screen, select [SECURITY] from the main menu, and select an item from the sub-menu.
Refer to “Navigating through the menu” (x
  page   57) for the operation of the menu screen.
 fWhen the projector is used for the first time
Initial password: Press  awsqawsq in order

, and press the  button.
Attention
 f When you select the [SECURITY] menu and press the  button, entering a password is prompted. Enter the preset password and 
then continue operations of the [SECURITY] menu.
 fWhen the password has been changed previously

, enter the changed password, and press the  button.
Note
 fThe entered password is displayed with * marks on the screen. fAn error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.
[SECURITY PASSWORD]
Display the  [SECURITY PASSWORD] screen when the power is turned on with the  switch set 
to the  side. When the entered password is incorrect, the operation will be restricted to the power < v/b> 
button.
1)
 
Press 
 as to select [SECURITY PASSWORD].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the security password entry.
[ON] Enables the security password entry.
Note
 fThis item is set to [OFF] in the factory default setting or when the [PROJECT OR SETUP] menu  → [INITIALIZE] → [ALL USER DATA] is 
executed. Set it to [ON] as necessary.
 f Change the password periodically that is hard to guess. fThe security password is enabled after setting the item to [ON] and setting the  switch to .
[SECURITY PASSWORD CHANGE]
Change the security password.
1)
 
Press 
 as to select [SECURITY PASSWORD CHANGE].
2)
 
Press the  button.
 fThe 

[SECURITY PASSWORD CHANGE] screen is displayed.
3)
 
Press 
 asqw and the number ( - ) buttons to set the password.
 fUp to eight button operations can be set.
4)

 
Press the  button.
5)

 
Re-enter the password for the confirmation.
6)

 
Press the  button.
Note
 f The entered password is displayed with * marks on the screen. fWhen numerical values are used for the security password, the security password is required to be initialized if the remote control is lost. 
Consult your dealer for the method of initialization.
[DISPLAY SETTING]
Overlap the security message (text or image) over the projecting image.
1)
 
Press 
 as to select [DISPLAY SETTING].   
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 119
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Hides the security message.
[TEXT] Displays the text set in the [SECURITY] menu → [TEXT CHANGE].
[USER LOGO] Displays the image registered by the user.
Note
 fTo create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
[TEXT CHANGE]
Edit the text to be displayed when [TEXT] is selected in [DISPLA Y SETTING].
1)  
Press 
 as to select [TEXT CHANGE].
2)
 
Press the  button.
 fThe 

[TEXT CHANGE] screen is displayed.
3)
 
Press 
 asqw to select the text, and press the  button to enter the text.
4)
 
Press 
 asqw to select [OK], and press the  button.
 fThe text is changed.
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote control.
1)
 
Press 
 as to select [CONTROL DEVICE SETUP].
2)
 
Press the  button.
 fThe 

[CONTROL DEVICE SETUP] screen is displayed.
3)
 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
[CONTROL PANEL] Sets the limitation on the control from the control panel.
[REMOTE CONTROL] Sets the limitation on the control from the remote control.
4) Press the  button.
 fThe 

[CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.
5)
 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)
 
Press 
 qw to switch the item.
 fY

ou can set the operation restriction from the control panel or the remot\
e control.
[ENABLE] Enables all button operations.
[DISABLE] Disables all button operations.
[USER] Operation of all buttons can be enabled/disabled separately.
Refer to “Enabling/disabling any button” (
x
  page   119) for details.
7) Press as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
8)

 
Press 
 qw to select [OK], and press the  button.
Enabling/disabling any button
1) Press  as to select [CONTROL DEVICE SETUP].
2)  
Press the  button.
 fThe 

[CONTROL DEVICE SETUP] screen is displayed.
3)
 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].   
						

							Chapter 4 Settings — [SECURITY] menu
120 - ENGLISH
4) Press the  button.
 fThe 

[CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.
5)
 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)
 
Press 
 qw to switch [USER].
7)
 
Press 
 as to select the button item to set.
 fWhen [INPUT

 SELECT BUTTON] is selected in [REMOTE CONTROL], press the  button, and 
then press as to select the button to set.
Buttons that can be set
[CONTROL PANEL] [REMOTE CONTROL]
[POWER BUTTON] Power button
[INPUT SELECT BUTTON]  button  button,  button, 
 button,  button,  
button,  button
[MENU BUTTON]  button
[AUTO SETUP BUTTON] ― button
[ON SCREEN BUTTON] ― button
[OTHER BUTTON] asqw,  button Buttons not listed above
8) Press 
qw to switch the item.
[ENABLE] Enables button operations.
[DISABLE] Disables button operations.
 fFollowing items can be selected only when [COMPUTER1/2 BUTT ON] is selected in [INPUT SELECT 
BUTTON].
[TOGGLE] Switches between [COMPUTER1] and [COMPUTER2] when the button is operated.
[COMPUTER1] Fixes to [COMPUTER1].
[COMPUTER2] Fixes to [COMPUTER2].
[DISABLE] Disables button operations.
 fWhen [INPUT  SELECT BUTTON] is selected in Step 7), pressing the  button returns to the 
[CONTROL PANEL] screen or the [REMOTE CONTROL]  screen once the item is switched.
9)
 
Press 
 as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
10)

 
Press 
 qw to select [OK], and press the  button.
Note
 f When a button operation is performed on the device set to [DISABLE], the  [CONTROL  DEVICE PASSWORD] screen is displayed.
Enter the control device password.
 f The 

[CONTROL DEVICE PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.
 fIf the operations of both [CONTROL

 PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
 f When the setting has completed, the menu screen will disappear

. To operate continuously, press the  button to display the main 
menu.
 f Even when you set button operations on the remote control disabled, operations of the  and  buttons on the remote 
control are kept enabled.
[CONTROL DEVICE PASSWORD CHANGE]
The control device password can be changed.
1)
 
Press 
 as to select [CONTROL DEVICE PASSWORD CHANGE].
2)
 
Press the  button.
 fThe 

[CONTROL DEVICE PASSWORD CHANGE]  screen is displayed.
3)
 
Press 
 asqw to select the text, and press the  button to enter the text.
4)
 
Press 
 asqw to select [OK], and press the  button.
 fT

o cancel, select [CANCEL].