Panasonic LCD Projector PT-LB10NTU PT-LB10U PT-LB10VU PT-LB10SU Operating Instructions

							ENGLISH-21
Getting started
Connections
Notes on connections
BRead the instruction manual for each peripheral device carefully before
connecting it.
BTurn off the power supply for all peripheral devices before making any
connections.
BIf the cables necessary for connection are not included with the peripheral
device or available as an option, you may need to prepare a proper cable
for the device concerned.
BIf there is a lot of jitter in the video signal, the projected image may flicker.
In such cases, it will be necessary to connect a TBC (time base corrector).
BRefer to the list on page 60 for details on compatible signals which can be
input to the projector.
BOnly one audio system circuit is available for the AUDIO IN L-R
connectors, so if you change the audio input source, you will need to
remove and insert the appropriate plugs.
Connecting to computer
RGB signal cable
(accessory)
Computer DIN 8-pin
(male) Computer for
control useMonitor
RGB signal cableRefer to the accessory CD-
ROM for details on the wireless
network that is used for
controlling the projector with a
personal computer by means
of the wireless card. 
(PT-LB10NTU only) Serial adapter
(ET-ADSER : sold
separately) 
						

							22-ENGLISH
NOTE:
BIf the signal cables are disconnected or if the power supply for the
computer or video deck is turned off while “D.ZOOM”(digital zoom) or
“INDEX WINDOW” is being used, these functions will be cancelled.
Connecting to video equipment
D-sub15-pin (male) - BNCx5 (male) adapter cable
DVD player
(with component
video connectors)
DIN 8-pin
(male)
DVD player Video deckComputer for control use
Red (connect to PRsignal connector)
Blue (connect to P
Bsignal connector)
Green (connect to Y signal connector)
BNC/RCA adapter Serial adapter
(ET-ADSER :
sold separately) 
						

							ENGLISH-23
Getting started
Insert the accessory lithium battery while making sure that the polarities are correct.
#While pushing the battery holder tab to the right, pull out the battery
holder.
$Insert the battery into the battery holder so that the + side is facing
upward.
%Insert the battery holder.
Preparation for the remote control unit
NOTE:
BDo not drop the remote control unit.
BKeep the remote control unit away from liquids.
BRemove the battery if not using the remote control unit for long periods.
BUse only CR2025 batteries as replacement batteries.
BIf the remote control unit is held so that it is facing directly in front of the
remote control signal receptor, the operating range is within
approximately 7 m (23´) from the surfaces of the receptor. Furthermore,
the remote control unit can be operated from an angle of ±30° to the left
or right and ±15° above or below the receptors.
BIf there are any obstacles in between the remote control unit and the
receptor, the remote control unit may not operate correctly.
BIf strong light is allowed to shine onto the remote control signal receptor,
correct projector operation may not be possible. Place the projector as
far away from light sources as possible.
B
If facing the remote control unit toward the screen to operate the projector,
the operating range of the remote control unit will be limited by the amount
of light reflection loss caused by the characteristics of the screen used.
Push the tab
Pull out
Back side
Match the “+”
surface of the
battery with the
“+” marked side of
the battery holder. 
						

							ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
)
*
$
&
(
'
#
Turning on the power
Before turning on the power
1, Ensure that all peripheral
devices are connected
properly.
2, Remove the lens cover.
Lens coverPower cord
Connect the accessory power cord to the AC IN
socket.
BThe power indicator on the projector will illuminate red.
Press the POWER button.
BThe power indicator on the projector will flash green. After a short
period, the indicator will illuminate green, and a picture will be
projected.
Turn on the power of all connected devices.
BStart the play function of a device such as a DVD player.
NOTE:
B
If the power cord was disconnected during projection when the projector
was used the last time, projection will start after the mains lead is
connected (when “POWER MEMORY” in the “OPTION2” menu is set to
“ON”). Refer to page 46 for details.
BA tinkling sound may be heard when the lamp unit is turned on, but this
is not a sign of a malfunction.
#
$
%
24-ENGLISH
Power indicator  
						

							ENGLISH-25
Basic Operation
Press the input select button to select the
input signal.
Follow the procedure below when you set the projector up first, and when
you change the setup place.
Press the AUTO SETUP button to initiate
automatic positioning.
BThe tilt of the projector and the input
signal will be detected and keystone
distortion and the position of the
image will be corrected.
(Refer to page 28 for details.)
Adjusting the size
BTurn the zoom ring to adjust the size of the projected image.
Adjusting the focus
BTurn the focus ring to adjust the focus of the projected image.
AUTO SETUP
Input select
buttons 
Changing
signalsVIDEORGB
7*%&0
3(#/&5803,
47*%&07*%&0
47*%&0
3(#
/&5803,
&
'
)
* (
Adjusting the angle
BWhile pressing the adjuster buttons,
adjust the forward/back angle of tilt
of the projector. Adjust so that the
projector is as vertical to the screen
as possible. BA picture will be projected in accordance with the selected input
signal.
BWhen a YP
BPRsignal is being input, “YPBPR” will be displayed
instead of “RGB”.
B“NETWORK” is for PT-LB10NTU only. 
						

							FREEZESHUTTER
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
ENTER
#
$
%
Turning off the power
Power indicator
Press the POWER button.
B“POWER OFF” is displayed on the
screen.
Press the I I
or H H
button to select “OK”, and
then press the ENTER button.
BThe lamp unit will switch off and the picture will stop being projected.
(The power indicator on the projector will illuminate orange while the
cooling fan is still operating.)
NOTE:
BYou can also turn off the power by pressing the POWER button twice or
by holding it down for at least 0.5 seconds.
BWhen the projector is in standby mode (the power indicator on the
projector is illuminated red), the projector continues to draw approximately
6 W of power even when the cooling fan has stopped.
#
$
%   POWER OFF
   OK   CANCEL
Power
cord
Disconnect the power cord after the power
indicator on the projector illuminates red.
26-ENGLISH 
						

							ENGLISH-27
Basic Operation
Power indicator
Power indicator status
RedIlluminatedThe projector is in standby mode and image projection
is possible by pressing the POWER button.
A picture is being projected.
The lamp is cooling down after the power is turned
off. (The cooling fan is operating.)
The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated orange. (After a short period, a picture
will be projected.) The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated red. (After a short period, a picture will be
projected.) FlashingIlluminated
Illuminated
Flashing Green
OrangeProjector status
Direct power off function
You can disconnect the power cord during projection or immediately after
use and move the projector. The cooling fan will operate by the internal
power supply to cool down the lamp.
BWhen this function is used, it may take more time for the lamp to turn back
on again compared to when the lamp cools down with the power cord
connected.
BDo not put the projector in a bag while the cooling fan is operating.
CAUTION
If not using the projector for an extended period of time, disconnect the
power cord plug from the wall outlet.
BIf dust builds up on the power cord plug, the resulting humidity may
damage the insulation, which could result in fire.
BThis projector continues to draw approximately 6 W of power even when
the power is turned off. 
						

							28-ENGLISH
Correcting keystone distortion and
automatic positioning (AUTO SETUP)
This projector detects its degree of tilt and the input signal. Keystone
distortion and the position of the image can then be corrected automatically
in accordance with the input signal.
ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
Projector control panelPress the AUTO SETUP button.
(When the projected image has caused keystone distortion)
BAutomatic positioning
will be carried out.
Screen
Projected
image
[
NOTE:
B“AUTO SEARCH” will also be carried out. (When “AUTO SEARCH” is
set to “ON”, refer to page 44 for details.)
BWhen RGB signals are being input, “DOT CLOCK”, and “CLOCK
PHASE” will be adjusted automatically in addition to keystone distortion
and the position of the image being corrected (except when the dot clock
frequency is 100 MHz or higher). Refer to page 40 for details.
BIf the edges of the projected image are indistinct, or if a dark picture is
being projected, the automatic setup processing may stop automatically
before it is complete. If this happens, project a different picture and then
press the AUTO SETUP button again.
BSet “AUTO KEYSTN” in the “OPTION1” menu to “OFF” to prevent any
deterioration of the picture as a result of keystone correction. 
(Refer to page 44.) 
						

							ENGLISH-29
Useful functions
Turning off the picture and sound
momentarily (SHUTTER)
The “SHUTTER” function can be used to momentarily turn off the picture and
sound from the projector when the projector is not being used for short
periods of time, such as during breaks in meetings or when carrying out
preparation. The projector uses less power in “SHUTTER” mode than it does
in normal projection mode.
ENTER
FREEZE
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
SHUTTER
ENTER
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
SHUTTERFREEZE
Still picture
BThe picture being projected will be paused.
BPress the FREEZE button again to cancel the
still picture. Press the SHUTTER button.
BThe picture and sound will be turned off.
BPress any button on either the projector or
remote control unit to return to normal operating
mode.
Press the FREEZE button.
NOTE:
B“SHUTTER” on the “MAIN MENU” is the same
function.
Pausing a picture (FREEZE)
NOTE:
BThe FREEZE button will be disabled when
“NETWORK” is selected. (PT-LB10NTU only) 
						

							30-ENGLISH
ENTER
INDEX
WINDOW
PROJECTOR VOLUMESTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
SHUTTERFREEZE
D.ZOOM
BThe picture will then
be enlarged to 1.5
times the normal size.
The remote control unit functions during D.ZOOM (digital zoom)
Press the F,G,IandHbuttons to move the enlarged area which you want to project.
Press the D.ZOOM +/- buttons to change the enlargement ratio.
Press the MENU button to return to the normal screen.
INDEX
WINDOW
PROJECTORSTD
D.ZOOMVOLUME
[
Enlarging the picture (D.ZOOM)
Adjusting the volume (VOLUME)
Press the D.ZOOM +/- button.
Press the VOLUME +/- button.
BPress the + button to raise the volume.
BPress the - button to lower the volume.
NOTE:
BThe enlargement ratio can be changed within the range of x1 to x2, in
steps of 0.1. When RGB signals are being input, the enlargement ratio
can be changed within the range of x1 to x3, except when the “FRAME
LOCK” is set to “ON”.
BIf the type of signal being input changes while the digital zoom function
is being used, the digital zoom function will be cancelled.
NOTE:
BYou can also select “VOLUME” from the
“MAIN MENU” to adjust the volume.
BThe VOLUME button will be disabled when
“NETWORK” is selected. (PT-LB10NTU only)