Panasonic Kx-tvs90 Voice Processing System Installation Manual

INSTALLATION
Installation Manual 31
2.5 INSTALLATION STEPS
The following is an overview of the standard installation process using Digital Integration. 
When necessary, other sections in this manual have been referenced for more detailed 
descriptions or instructions.
1.Obtain a list of current users, their extension numbers, their departments, and the type of 
systems they use (mailbox, no mailbox, beeper, car phone, etc.).
2.Assess your customers needs before setting up the system. You will save...

INSTALLATION
32 Installation Manual
CAUTION
If the DIP Switch is not reset to position 0 after initialization, all programming will be 
lost when the voice processor loses power!
5.Perform Quick Setup (see Section 5 CUSTOMIZING THE SYSTEM).
6.Check Quick Setup:
The Power Indicator on the Voice Processor should be solid.
The screen output should be: [On Line].
If you do not see the On Line message, check the following:
The line cord to the Voice Processor has 4 conductors.
The programming on the...

INSTALLATION
Installation Manual 33
2.6 CONNECTIONS
2.6.1 Connecting to the PBX
The VPS can be connected to up to 2 extension ports of the PBX. Use a 4-conductor wire for 
connection with KX-TA624 that uses APT Integration, and for connection with KX-T series 
systems that use DPT Integration. Use a 2-conductor wire for connection to all other PBXs.
2.6.2 Opening the Ferrite Core
Insert your finger into the opening of the ferrite core and open it as shown below:
Connect a 4-conductor cable or 2-conductor...

INSTALLATION
34 Installation Manual
2.6.3 Connection for APT Integration
Ports 1-2 of the VPS
2.6.4 Connection for DPT Integration
Ports 1-2 of the VPS
YGRB
YGRB
To KX-TA624
PORT 1
PORT 2
PORT 1
Telephone Line
Modular Jacks
To Extension
Port of the PBX
PORT 2
Extension Jacks 07 and 08 
(or 15 and 16)
YGRB
YGRB
To a KX-T series PBX that uses DPT Integration
To Extension
Port of the PBX
PORT 1
PORT 2
PORT 1
Telephone Line
Modular Jacks
PORT 2
Any Extension Jack except Jack 01 

INSTALLATION
Installation Manual 35
2.6.5 Connection for Non-APT/DPT Integration
Ports 1-2 of the VPS
GRGR
To Extension Ports of
Non-APT/DPT Integration PBX
PORT 1
PORT 2
PORT 1
Telephone Line
Modular Jacks
To Extension
Port of the PBX
PORT 2 

INSTALLATION
36 Installation Manual
2.7 TERMINAL CONNECTION
2.7.1 Requirements for Connecting Programming Terminal
The programming terminal must be connected with a serial cable with an RS-232C connector 
at the RS-232C port. This must be a null modem cable. This enables system administration 
(system setup, mailbox setup, and system diagnosis) to be performed.
Communication parameters of the VPS have been set to the following values at the factory:
2.7.2 Connecting the RS-232C Cable
RECOMMENDED:
Before...

INSTALLATION
Installation Manual 37
Table 7  Pin Configuration of the RS-232C
Pin
NumberSignal NameCircuit Type
RS-232C CCITT
1
2FG
TXDFrame Ground
Transmitted DataAA
BA101
103
3
4RXD
RTSReceived Data
Request To SendBB
CA104
105
Circuit
type
(EIA)Signal
namePin
no.Circuit
type
(EIA) Signal
namePin
no.
BB
BA
CD
AB
CCBB
BA
CD
AB
CC 2
3
4
5
62
3
4
5
6 RXD
TXD
DTR
SG
DSRRXD
TXD
DTR
SG
DSR
CA
CB 7
8RT S
CTS
Circuit
type
(EIA)Signal
name
VPS (9 pin)25-pin Cable Printer/PC
VPS (9 pin)9-pin Cable...

INSTALLATION
38 Installation Manual
2.7.3 RS-232C Signals
Frame Ground (FG)
Connects an external ground to the unit frame, usually the ground pin of the AC power cord.
Transmitted Data (TXD)—output
Conveys signals from the unit to the terminal/printer. A mark condition is held unless data 
or BREAK signals are being transmitted.
Received Data (RXD)—input
Conveys signals from the terminal/printer to the unit.
Request To Send (RTS)—output
This lead is held on whenever DSR is on.
Signal Ground (SG)
Connects...

INTEGRATING THE VPS WITH PANASONIC KX-T PHONE SYSTEMS
Installation Manual 39
Section 3
INTEGRATING THE VPS WITH
PANASONIC KX-T PHONE SYSTEMS 

INTEGRATING THE VPS WITH PANASONIC KX-T PHONE SYSTEMS
40 Installation Manual
3.1 GUIDELINES FOR INTEGRATION
3.1.1 APT/DPT or Inband Signaling?
There are 3 types of integration available on the VPS: Inband Signaling, APT and DPT. The 
VPS used with any other brand of telephone equipment requires inband equipment.
KX-TA624 that can use APT Integration is:
KX-TA624 Version Y581A or higher.
KX-TD series PBXs that can use DPT Integration are:
KX-TD308 Version P871F or higher
KX-TD816 Version P301O or...