Panasonic Kx-tvs90 Voice Processing System Installation Manual

VOICE PROCESSING SYSTEM OVERVIEW
Installation Manual 21
1.3.5 Specifications
1.3.6 Hardware
2 Flash Memory Cards.
2 Telephone Inputs (RJ11C)
1 RS-232C Connector
1 DIP Switch (4-bit)
1.3.7 Recommendations for System Configuration
General guideline: a ratio of 6/1 (for every 6 lines, 1 port). There are 2 questions to ask when 
considering how many ports are desirable:
Are the ports answering all incoming calls or just forwarded/transferred calls?
If they are answering incoming calls, how busy are the...

VOICE PROCESSING SYSTEM OVERVIEW
22 Installation Manual
One port may not support an Automated Attendant configuration with 5 CO lines. The 
preceding recommendations for Automated Attendant ports may have to be modified for heavy 
traffic.
Table 4 
CO Lines Port
1-4 1
5-8 2 

VOICE PROCESSING SYSTEM OVERVIEW
Installation Manual 23
1.4 DIGITAL INTEGRATION
1.4.1 General
There are 2 types of Digital Integration: APT Integration and DPT Integration.
APT Integration is available when the VPS is connected to a KX-TA624. DPT Integration is 
available when the VPS is connected to a KX-TD or KX-TA1232 digital PBX.
1.4.2 APT Integration
To the Panasonic KX-TA624, the VPS ports look like proprietary telephones. The PBX thinks 
that the VPS is a proprietary telephone, and the VPS mimics...

VOICE PROCESSING SYSTEM OVERVIEW
24 Installation Manual
1.4.4 DPT Integration
To the Panasonic KX-T series PBX that uses DPT Integration, the VPS ports look like digital 
extensions. The PBX thinks that the VPS is a digital phone, and the VPS mimics all actions of 
a digital set. Another advantage of digital integration is that the 2B+D communication provides 
2 VPS ports for each Digital Station port. Communication between the VPS and the PBX 
through digital integration requires the proper software...

INSTALLATION
Installation Manual 25
Section 2
INSTALLATION 

INSTALLATION
26 Installation Manual
2.1 SAFETY PRECAUTIONS
Please read the following precautions before installing the VPS.
2.1.1 Installation
The VPS needs to be mounted on a wall. Improper placement of the system may result in 
malfunction, noise, or discoloration. Avoid installing the VPS in the following places:
in direct sunlight; in hot, cold, or humid places
in new areas where there are thermal springs, etc. (where sulfuric gas may damage the 
equipment or contacts).
where shocks or vibrations...

INSTALLATION
Installation Manual 27
2.1.2 Wiring
To assure good quality telephone connection, it is recommended new and modifications to 
existing installation of customer premise wiring shall use solid twisted pair copper 
conductors with minimum 24 gauge that comply with the electrical specifications for 
Category 3 wiring as detailed in ANSI/EIA/TIA-570A Building Wiring Standards.
Do not wire the telephone cable parallel to an AC power source, computer, etc. If cables 
are run near those wires,...

INSTALLATION
28 Installation Manual
2.2 UNPACKING
Unpack the box and check the items below.
Table 5 
Main Unit 1
AC Cord 1
Screws (Wall Mounting) 3
Anchor Plugs (Wall Mounting) 3 

INSTALLATION
Installation Manual 29
2.3 MOUNTING THE VPS ON THE WALL
The wall where the VPS is to be mounted must be able to support the weight of the VPS. If 
screws other than the ones supplied are used, use the same-sized diameter screws as the 
enclosed ones.
To Mount on a Wooden Wall:
1.
Place the template (included) on the wall to mark the 3 screw positions.
2.Install the 3 screws (included accessories) into the wall.
3.Hook the unit on the screw heads.
Template
Wooden
Wall
Drive the screw
to this...

INSTALLATION
30 Installation Manual
2.4 FRAME GROUND CONNECTION
IMPORTANT!!!
Connect the frame of the main unit to the ground.
1.Loosen the screw.
2.Insert the grounding wire.
3.Tighten the screw.
4.Connect the grounding wire to the ground.
In most of North America, the ground provided by the Third wire ground at the commercial 
or residential power outlet will be satisfactory. However, in some cases this ground may be 
installed incorrectly. Therefore, the following test procedure should be performed....