Panasonic Kx Tg9581 Operating Instructions Manual

Error messages
Display messageCause/solution
Base no power
or
No link. Re-connect
base AC adaptor.RThe handset has lost communication with the base unit. Move
closer to the base unit and try again.
R Unplug the base unit’s AC adaptor to reset the unit. Reconnect
the adaptor and try again.
R The handset’s registration may have been canceled. Re-register
the handset (page 52).
BusyRNo cellular phone is paired to the base unit. Pair a cellular phone
(page 19).
R The called unit is in use.
R Other units are...

TroubleshootingIf you still have difficulties after following the instructions in this section, disconnect the base unit’s AC
adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset, and then
insert the batteries into the handset again.
General use
ProblemCause/solution
The handset does not turn on
even after installing charged
batteries.R Place the handset on the charger to turn on the handset.
The unit does not work.RMake sure the batteries are installed correctly...

ProblemCause/solution
I cannot hear a dial tone.RMake sure that the CELL indicator lights up (page 16).
R The base unit’s AC adaptor or telephone line cord is not
connected. Check the connections.
R Disconnect the base unit from the telephone line and connect
the line to a known working telephone. If the working telephone
operates properly, contact our service personnel to have the
unit repaired. If the working telephone does not operate
properly, contact your service provider/telephone company.
The...

ProblemCause/solution
The handset or base unit does
not ring.RThe ringer volume for landline is turned off. Adjust the ringer
volume (page 46).
R The ringer volume for cellular line is turned off. Adjust the ringer
volume (page 45).
R When one handset is selected to ring for cellular calls, other
units do not ring. To change the selection, see page 20.
R Silent mode is turned on. Turn it off (page 50).
I cannot make local calls with the
handset or base unit using a
cellular line.RYou need to add your...

ProblemCause/solution
Caller information is not
announced.RThe ringer volume for landline is turned off. Adjust the ringer
volume (page 46).
R The ringer volume for cellular line is turned off. Adjust the ringer
volume (page 45).
R When one handset is selected to ring for cellular calls, other
units do not announce caller information. To change the
selection, see page 20.
R The Talking Caller ID feature is turned off. Turn it on (page 47).
R The ring as cell mode is set to  “On (without Talking
CID) ”....

ProblemCause/solution
Noise is heard during a call on
the headset.RA Bluetooth headset can communicate with the base unit within
a range of approximately 10 m (33 feet). The connection may
be subject to interference from obstructions such as walls or
electronic devices. Move closer to the base unit.
I cannot connect my headset to
the base unit.RConfirm that your headset is turned on.
R If your headset is already connected to another Bluetooth
device such as your cellular phone, disconnect the headset...

Answering system
ProblemCause/solution
The unit does not record new
messages.RThe answering system is turned off. Turn it on (page 61).
R The answering system does not answer or record calls from
cellular lines.
R The message memory is full. Erase unnecessary messages
(page 63, 64).
R The greeting setting is set to  “Greeting only ” or
“ Greeting1&Only ”. Change the setting (page 61).
R Your service provider/telephone company’s voice mail service
may be answering your calls before the unit’s answering...

ProblemCause/solution
The caller information shown on
the unit’s display (handset and
base unit) differs from the
information shown on the pop-up
window on the computer.RWhen calls are received on several lines including landlines or
cellular lines at the same time, the caller information shown on
the pop-up window which appears at the front may differ from
the information shown on the unit’s display (handset and base
unit). To answer the call that you want to pick up, check the
caller information on...

Liquid damage
ProblemCause/solution
Liquid or other form of moisture
has entered the handset/base
unit.RDisconnect the AC adaptor and telephone line cord from the
base unit. Remove the batteries from the handset and leave to
dry for at least 3 days. After the handset/base unit are
completely dry, reconnect the AC adaptor and telephone line
cord. Insert the batteries and charge fully before use. If the unit
does not work properly, contact an authorized service center.
Caution:
RTo avoid permanent damage,...

FCC and other information
80For assistance, please visit http://www.panasonic.com/help
Useful Information

TG958x_0704_ver031.pdf   802014/07/04   10:32:29This equipment complies with Part 68 of the FCC rules 
and the requirements adopted by the ACTA. On the 
bottom of this equipment is a label that contains, 
among other information, a product identifier in the 
format US:ACJ----------.
If requested, this number must be provided to the 
telephone company.
L Registration No.............(found on the...