Panasonic Kx Tg2730 Operating Instructions Manual
Have a look at the manual Panasonic Kx Tg2730 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation 11 Preparation For assistance, please call: 1-800-211-PANA(7262) Connections •USE ONLY WITH Panasonic AC ADAPTOR PQLV10 (Order No. PQLV10Z). •The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) •To connect a standard telephone on the same line, see page 82. •If your unit is connected to a PBX which does not support Caller ID services, you cannot access those services. Hook Telephone Line CordAC AdaptorPower Outlet (AC 120 V, 60 Hz) Single-Line Telephone Jack (RJ11C)Fasten the AC adaptor cord to prevent it from being disconnected. Raise the antennas.
Installation 12Battery strength You can check the battery strength on the handset display. The battery strength is as shown in the chart below. Display promptBattery strength Fully charged Medium Low Needs to be recharged. Discharged Battery Charge Place the handset on the base unit and charge for about 15 hoursbefore initial use. •The CHARGE indicator lights, a beep sounds and “Charging” will be displayed. Installing the Battery in the Handset Insert the battery into the handset as shown, matching the correct polarity (#). Press the battery down until it places into the compartment ($). When finished, close the cover. CHARGE Indicator 1 2
13 Preparation For assistance, please call: 1-800-211-PANA(7262) •The battery operating time may be shortened depending on usage conditions and ambient temperature. •Clean the handset and the base unit charge contacts with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity.Otherwise the battery may not charge properly. •If the battery is fully charged, you do not have to place the handset on the base unit until “Recharge battery” is displayed and/or “” flashes. This will maximize the battery life. •The battery cannot be overcharged. Recharge Recharge the battery when: — “Recharge battery” is displayed on the handset, —“ ” flashes on the display, or — the handset beeps intermittently while it is in use. •If you DO NOT recharge the handset battery for more than 15 minutes, the display will continually indicate “Recharge battery” and/or “” will flash when the handset is lifted off the base unit. •If the battery has been discharged, the handset will display “Charge for 15HRS” and “” when you place the handset on the base unit. The handset will not work. Keep charging. Battery information After your Panasonic battery is fully charged (p. 12): SPPRIVACY[1] Recharge battery PLAY OperationOperating time While in use (TALK) While not in use (Standby) While using the Reception Booster feature (p. 29)Up to 4.5 hours Up to 11 days Up to 3.5 hours When using the 2-Way Radio mode (p. 58) with the battery fully charged: OperationOperating time While in use (TALK) While not in use (Standby)Up to 4.5 hours Up to 12 hours
Programmable Settings 14 Programming Guidelines This unit has programmable functions. Most of them are selected from the function menu on the display (p. 15). How to select a function item from the menu Make sure the handset is not being used. 1. Press (CONF/FUNCTION). •The main menu is displayed (p. 15). 2. You can scroll through the menu by pressing Öor Ñ. Scroll to the desired item by pressing Öor Ñ. 3. Press áto select the item. 4. If the item has a sub-menu I, it will be displayed. Select the sub-menu item by pressing Öor Ñ, and press á. If the sub-menu Iitem has the sub-menu II, it will be displayed. Select the sub-menu IIitem in the same way. 5. You can then select the desired setting by pressing Öor Ñ. 6. To save the setting, press the right soft key (). •When programming is complete, a confirmation tone sounds. The display will return to the main menu or the sub-menu Ior the sub-menu II(if the function item is in the sub-menu Ior in the sub-menu II). You can continue programming other items. To exit the menu, press (OFF). Useful information: •“---------------” indicates the beginning or end of the function menu. • You can go back to the previous display by pressing Üexcept when entering characters or numbers. To return to the main menu from the sub-menu Ior sub-menu II, press Ü. SAVE Save directory HRinger setting Date and time Ringer volume HRinger tone Incoming call Ringer tone :1GFSAVE --------------- HSave directoryRinger setting Ex. Ringer tone setting The right soft key works as the key when “” displays above it. (OFF) SAVE SAVE Navigator key has four active areas that are indicated by arrows. The key is indicated by the arrows Ñ, Ö, Üor áin the Operating Instructions.SAVE (CONF/FUNCTION) SAVE
15 Preparation For assistance, please call: 1-800-211-PANA(7262) •You can exit the programming mode any time by pressing (OFF). •If you do not press any buttons for 60 seconds, the handset will exit the programming mode. •If the unit detects a problem, an error message will be displayed (p. 86). Function Menu Table You can use the following functions to customize your unit. After pressing (CONF/FUNCTION), the main menu is displayed. Most items in the main menu have a sub-menu I. The sub-menu Iis shown after selecting the item in the main menu. If the sub-menu Iitem has the sub-menu II, it will be displayed after selecting that sub-menu I item. See the corresponding pages for function details. Save directoryp. 42 p. 21 Ringer setting Date and time Copy directory Initial setting p. 19 p. 62 p. 63Ringer volume Ringer tone Incoming call p. 47Copy 1 item p. 48Copy all items p. 20LCD contrast p. 18Auto talk p. 56Room monitor p. 38Caller ID edit Set tel line Registration p. 16Set dial mode p. 61Set flash time p. 17Set line mode Set answeringp. 25Number of rings p. 24Recording time p. 75Remote code p. 65Set mailbox2&3 Set base unitp. 63Incoming call p. 56Room monitor p. 85HS registration p. 84Deregistration 2Way radio modep. 58 Main menuSub-menu ISub-menu II (for Handset) (for Base unit)
Programmable Settings 16 Dialing Mode If you have touch tone service, set to “Tone”. If rotary or pulse service is used, set to “Pulse”. Your phone comes from the factory set to “Tone”. Make sure the base unit and the handset are not being used. 1 Press (CONF/FUNCTION). 2 Scroll to “Initial setting” by pressing Öor Ñ. 3 Press á. 4 Scroll to “Set tel line” by pressing Ö or Ñ. 5 Press á. 6 Press áat “Set dial mode”. •The current setting is displayed. 7 Select “Pulse” or “Tone” by pressing Öor Ñ. 8 Press the right soft key ( ). •A beep sounds. •To exit the programming mode, press (OFF). •You can exit the programming mode any time by pressing (OFF) . SAVE Set dial mode :ToneGFSAVE Caller ID edit HSet tel line Set answering --------------- HSave directory Ringer setting Copy directory HInitial setting 2Way radio mode --------------- HLCD contrast Auto talk --------------- HSet dial mode Set flash time Set dial mode :PulseGFSAVE Set dial mode :Pulse
17 Preparation For assistance, please call: 1-800-211-PANA(7262) Line Mode If the line is connected to a low voltage system such as a PBX, set to “B”. Your phone comes from the factory set to “A”. Make sure the base unit and the handset are not being used. 1 Press (CONF/FUNCTION). 2 Scroll to “Initial setting” by pressing Öor Ñ,and press á. 3 Scroll to “Set tel line” by pressing Ö or Ñ. 4 Pressá. 5 Scroll to “Set line mode” by pressing Ö or Ñ. 6 Press á. •The current setting is displayed. 7 Select “B” or “A” by pressing Öor Ñ. 8 Press the right soft key ( ). •A beep sounds. •To exit the programming mode, press (OFF). •You can exit the programming mode any time by pressing (OFF) . SAVE Set line mode :AGFSAVE --------------- HSet dial mode Set flash time Set line mode :BGFSAVE Set line mode :B Set flash time HSet line mode --------------- Caller ID edit HSet tel line Set answering --------------- HSave directory Ringer setting Copy directory HInitial setting 2Way radio mode
Programmable Settings 18 Auto Talk Feature The Auto Talk feature allows you to answer a call by lifting the handset off the base unit without pressing or . If you purchase an additional handset (p. 26), you can answer a call by lifting it off the charger. If you want to use this feature, turn the feature ON by programming. Your phone comes from the factory set to OFF. Make sure the handset is not being used. 1 Press (CONF/FUNCTION). 2 Scroll to “Initial setting” by pressing Öor Ñ. 3 Press á. 4 Scroll to “Auto talk” by pressing Öor Ñ. 5 Press á. •The current setting is displayed. 6 Select “On” or “Off” by pressing Öor Ñ. 7 Press the right soft key ( ). •A beep sounds. •To exit the programming mode, press (OFF). •You can exit the programming mode any time by pressing (OFF) . •In order to view Caller ID information after you lift up the handset to answer a call, leave the Auto Talk feature OFF. SAVE Auto talk :Off GFSAVE Copy directory HInitial setting 2Way radio mode --------------- HSave directory Ringer setting Auto talk :On Auto talk :OnGFSAVE --------------- HLCD contrast Auto talk LCD contrast HAuto talk Room monitor
19 Preparation For assistance, please call: 1-800-211-PANA(7262) Ringer Volume Handset You can program the handset ringer volume to HIGH, MEDIUM, LOW or OFF. If set to OFF, the handset will not ring for external calls, and for internal calls it will ring at the LOW level. Your phone comes from the factory set to HIGH. Make sure the handset is not being used. 1 Press (CONF/FUNCTION). 2 Scroll to “Ringer setting” by pressing Öor Ñ, and press á. 3 Press áat “Ringer volume”. 4 Select the desired volume by pressing Öor Ñ. •Each time you press Öor Ñ, the volume will change and ring. •To turn the ringer OFF: press Örepeatedly until “Off ?” displays. 5 Press the right soft key ( ). •A beep sounds. To turn the ringer ON: Press Ñin step 4, and press the right soft key ( ). •The ringer will sound at the LOW level. •You can exit the programming mode any time by pressing (OFF) . •If set to OFF,“Ringer off”will be displayed while the handset is not in use. •You can also select the ringer volume while an external call is being received. Press Öor Ñwhile the handset is just ringing. •To adjust the ringer volume for the 2-Way Radio mode, see page 59. •You can change the ringer tone for external calls. See page 62. SAVE SAVE HIGH MEDIUM OFF Save directory HRinger setting Date and time Ringer volume Low High Ringer volume Low High Ringer volume RingerOff ? LOW --------------- HRinger volume Ringer tone Ringer volume Low HighGFSAVE Ñ Ñ ÑÖ Ö Ö
Programmable Settings 20 Base unit You can set the base unit ringer volume to HIGH, MEDIUM, LOW or OFF. If set to OFF, the base unit will not ring for external calls, and for internal calls it will ring at the LOW level. Your phone comes from the factory set to HIGH. Make sure the base unit is not being used. To select HIGH (preset), MEDIUM or LOW, press (RINGER/AUTO). •Each time you press the button, the ringer volume will change and ring. To turn the ringer OFF, press and hold (RINGER/AUTO)until 2 beeps sound. •“” is displayed. To turn the ringer ON, press (RINGER/AUTO). •The ringer will sound at the LOW level. •You can also select the ringer volume while an external call is being received. Press (RINGER/AUTO), Öor Ñwhile the base unit is just ringing. •You can change the ringer tone for external calls. See page 62. RINGER OFF LCD Contrast You can program the handset LCD contrast (6 levels). Your phone comes from the factory set to level 3. Make sure the handset is not being used. 1 Press (CONF/FUNCTION). 2 Scroll to “Initial setting” by pressing Öor Ñ, and press á. 3 Press áat “LCD contrast”. 4 Select the desired contrast by pressing Ö or Ñ. •Each time you press Öor Ñ, the LCD contrast will change. •The number of steps shows the LCD contrast level. 5 Press the right soft key ( ). •A beep sounds. •To exit the programming mode, press (OFF). •You can exit the programming mode any time by pressing (OFF) . SAVE --------------- HLCD contrast Auto talk LCD contrast Low HighGFSAVE LCD contrast Low High LCD contrast Low High Level 6 Level 4 Level 1 Copy directory HInitial setting 2Way radio mode