Panasonic Kx Tg1000n Operating Instructions Manual

11
Preparation
Battery Charge
Place the handset on the base unit and charge for about 12 hoursbefore
initial use. 
• The CHARGE indicator lights. 
CHARGE Indicator 
Installing the Battery in the Handset
Install the battery in the handset with the charge contacts facing down 
and close the handset cover, locking it into place.
H
While charging the battery, the 
battery icon cycles as shown
below.
Charge  
Contacts 

12
Up to 5.5 days
Recharge
Recharge the battery when: 
—“LOW BATTERY ” is displayed, or
—“ ”  fl ashes on the display.
Battery information
After your Panasonic battery is fully charged (p. 11):
OperationApprox. battery life
While in use (TALK) Up to 10 hours*
While not in use (Standby)
∗ In case the Range Extender Mode is set to  “OFF ” (p. 48).
• Battery life may be shortened depending on usage conditions and ambient 
temperature.
• Clean the handset and the base unit charge contacts with a soft, dry...

13
PreparationSelecting the Dialing Mode
You can program the dialing mode with the base unit. 
If you have touch tone service, set to “Tone ”. If rotary or pulse service is
used, set to  “Pulse ”. Your phone comes from the factory set to  “Tone ”.
Make sure the base unit is in the standby mode initially. 
1
Press (*)three times.
• A beep sounds, POWER and IN USE indicators 
fl ash quickly on the base unit.
2
To select “Tone”, press (7)repeatedly until the IN USE
indicator lights.
T
o select “Pulse”, press...

During programming: 
Press repeatedly to select the desired function item. 
Then press               to go to the next step.
•You can go back to the previous display by pressing  (OFF\bCLEAR)except when
entering characters or numbers. To return to the main menu from the sub-\
menu, 
press  (OFF\bCLEAR) .
•
You can exit the programming mode any time by pressing and holding  (OFF\bCLEAR).
•If you do not press any buttons for 10 seconds, the unit will return to \
the standby mode.
)(or)
(
14
Programmable...

HANDSET 1
RDLMEMMENU
CALLS LOG 
HANDSET SETTINGS
RANGE EXTENDERREGISTER
15
PreparationFunction Menu Table
You can program the following function items. The display shows the 
programming instructions. 
See the corresponding pages for function details. 
Make sure the handset is in the standby mode initially.
 To view the Caller List (p. 28). 
To select the range extender mode (p. 48). 
To re-register the handset (p. 55). 
To select the ringer volume (p. 16). 
To select the ringer melody (p. 49). 
To set...

With the handset
5 levels are available. Your phone comes from the factory set to level 2\
. 
When set to OFF, the handset will not ring.
1
Press .
2
Press to select
“
HANDSET SETTINGS”, and press 
.
3
Press to select
“ RINGER VOLUME ”, and press 
.
4
Press to increase or 
press             to decrease the
volume.
• The selected volume is displayed and 
rings.
• To turn the ringer OFF , erase “” 
all by pressing .
5
Press .
• A beep sounds.
• The display will return to the handset
settings menu.
• After...

17
Preparation
With the base unit
7 levels are available. Your phone comes from the factory set to level 2\
. 
When set to OFF, the base unit will not ring.
1
Press (*)three times.
•A beep sounds, POWER and IN USE indicators  flash quickly.
2
Press  VOLUMEÖor Ñto select the desired volume.
•Each time you press  VOLUMEÖ
or Ñ
, the volume will change 
and ring.
• To turn the ringer OFF , press VOLUME Örepeatedly until 
no sound is heard.
3
Press (#).
• A beep sounds.
To turn the ringer ON,  press VOLUMEÑin...

18
Selecting the LCD Contrast
You can select the LCD contrast level 1 to 16 by programming.  
Your phone comes from the factory set to level 9.
Make sure the handset is in the standby mode initially.
1
Press .
2
Press to select
“
HANDSET SETTINGS”, and press 
.
3
Press to select
“ CONTRAST ”, and press               .
4
Press or to select the
desired LCD contrast level.
• Each time you press or              ,  
the LCD contrast will change.
• If you select the minimum/maximum LCD
contrast level, the...

Making Calls
19
Basic Operation
1
Press .
2
Dial a phone number.
•The dialed number is displayed.
3
To hang up, press (OFF/CLE\bR)or place
the handset on the base unit.
• While the handset is in use, the IN USE indicator on the base unit light\
s.
• If “ SEARCHING FOR BASE ” and an alarm tone sounds in step 1, move closer to
the base unit, and try again.
• If “ LINE IN USE ” is displayed,the base unit or another handset is engaged in an
external call. Wait until “ LINE IN USE” disappears.
• While talking...

20
To adjust the receiver/speaker volume (5 levels) while talking
1
Press while talking.
2
To increase, press . 
To decrease press             .
3
Press .)
(OK
)(
)
(VOL
To have a hands-free phone conversation
1
Press (S\f-\fHONE).
2
Dial a phone number.
• The dialed number is displayed.
3
When the other party answers, talk into the 
microphone.
4
To hang up, press (OFF/CLE\bR)or place the handset on the base
unit.
• “PHONE OFF ” is displayed.
Hands-free Speakerphone
For best performance, please note the...